Page 1
The model and serial numbers are located on the bottom of the DSP master unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. XDP-MU110 Serial No.
Page 2
Warning Note on the lithium battery Do not expose the battery to excessive heat This equipment has been tested and found such as direct sunlight, fire or the like. to comply with the limits for a Class B digital device, pursuant to Part 15 of the Warning if your car’s ignition has no FCC Rules.
This system allows you to digitally integrate an iPod/iPhone into your existing car audio unit. You can enjoy exciting sound from your car audio unit and iPod/iPhone via this system, which features sound settings optimized for your vehicle type by using Sony’s original digital sound technology.
The System Components This section contains explanations on the location of controls and their basic operations. DSP master unit Sound setting switches page 8 Note Set each switch according to your car • Avoid touching the top of the DSP master unit type/interior.
Cradle Suction cup VOLUME (VOL) +/–* SEEK / buttons* SOURCE/OFF button Press to skip tracks. Press to turn on the power/change the source between a car audio unit and an Remote sensor iPod/iPhone. Indicator Press and hold more than two seconds You can check the status of the DSP to turn off the system.
LEFT/RIGHT buttons page 9 RM-X251 Card remote Press to adjust the speaker balance. commander Press and hold the CNT button () to return to the default setting. BASS (–/CNT/+) buttons page 9 Press to adjust the bass level. ...
See the following examples. Sound Settings Compact hatchback Optimized sound setting based on your vehicle This system provides well balanced sound, which appears to come from in front of the driver’s seat, optimized for the vehicle type VEHICLE SIZE: S by setting the DSP master unit.
Full sized SUV Adjusting the speaker balance Press the FRONT/REAR/LEFT/RIGHT buttons to adjust the balance between the speakers. An adjustment range of 7 steps is available for each speaker setting. Press and hold the VEHICLE SIZE: L CNT button to return to the default setting. SUBWOOFER: Y The default setting is CNT (center).
Adjusting the input volume from the iPod/iPhone Setting up the Cradle Press the ALO button. Precautions Adjust the playback volume level of an iPod/iPhone to the optimum level. Press the ALO button repeatedly to switch • Install the cradle on a dashboard properly so between ON and OFF.
Mounting sheet Notes • Choose the mounting location carefully. Practice installation before you actually mount the sheet, if necessary. • Removing the mounting sheet from the Strap dashboard decreases the adhesive strength of the mounting sheet. It should not be reused after removal.
Page 12
Notes • After you attach the strap to the cradle, pull • The suction cup may contain tiny holes. the strap gently to make sure that the strap This can occasionally occur in the is securely attached to the cradle. production process, and should not cause a •...
Page 13
Adjust the strap. Pull the tab of the cradle for a few seconds in the direction of the arrow marked in the Adjust the strap by using the adjuster. illustration below (), and then slowly Adjuster (over 3 to 5 seconds) remove the suction cup ().
Replace the cover on the suction cup. To secure the cradle cable Cover Note • Put the cover on the suction cup when you take the cradle off the dashboard. If the suction cup becomes dirty or scratched, its adhesive strength will be reduced. Arranging the cradle To release the cradle cable cable...
• Remove the case or cover from the iPod/iPhone before setting it in the cradle to ensure a stable installation. • Sony cannot accept responsibility in the event that data recorded to an iPod/iPhone is lost or damaged when using an iPod/iPhone connected to the cradle.
Page 16
To adjust the angle of the cradle • When removing the iPod/iPhone, do not twist or bend the iPod/iPhone as it may result in You can adjust the angle of the cradle as connector damage. shown in the illustration below. Do not use force to adjust the angle, as a malfunction may result.
Press the SOURCE/OFF button on the cradle or the remote commander Playback repeatedly until the LED indicator on the cradle turns red (page 6). Precautions • If you set an iPod/iPhone on the cradle • For safety reasons, keep your car audio unit when the system is on, the iPod/iPhone is and iPod/iPhone volume moderate so that selected as the source.
In such a case, consult your with safety and regulatory standards. Please nearest Sony dealer. note that the use of this accessory with iPod or iPhone may affect wireless performance. Warning...
Maintenance Specifications DSP Master Unit Replacing the lithium battery of the AUDIO POWER SPECIFICATIONS remote commander CEA2006 Standard When the battery becomes weak, the range Power Output: 17 Watts RMS 4 at of the remote commander becomes shorter. 4 Ohms < 1% THD+N Replace the battery with a new CR2025 SN Ratio: 80 dBA lithium battery.
Should any problem persist, stop using the The / buttons on the cradle do not system and consult your nearest Sony dealer. work. The car audio unit is selected as the source. DSP Master Unit...
Page 21
The arm does not hold the iPod/iPhone Sound reduces suddenly. Temperature detection could be activated. properly. The rubber used in the upper part of the arm – Be sure to place the system in a well becomes hard at low temperature. ventilated location.
Page 23
If you have any questions or problems concerning the system that are not covered in this manual, please consult your nearest Sony dealer. Nota Póngase en contacto con su distribuidor Sony más cercano en caso de tener cualquier consulta o problema relativos al sistema que no se hayan tratado en este manual.
Page 24
Gray, Gray/black striped) of the Hi-level input (Car Audio In) cable Si el sistema de audio del vehículo puede producir sonido en unit. In this case, please consult your nearest Sony al conectar la salida de audio del sistema de audio a la () to the car audio unit.
Page 25
Blue/White striped AMP REM Con rayas azules y blancas These terminals are for optional speakers. Not supplied. Left White Izquierdo Estos terminales se utilizan para altavoces Blanco opcionales. White/black striped No suministrado. Rayado blanco y negro Right Gray Derecho Rojo Gris Gray/black striped...