JVC GZ-MC200US Service Manual page 29

3.2.5 ASSEMBLY of [8]CAMERA ASSEMBLY
Disassembly procedure
STEP Fig.
PART NAME
No. No.
[1]
ROTARY UNIT C1
[2]
JOINT CASE ASSY
[3]
RING
[4]
POWER UNIT C2
[5]
LOWER CASE (OP) ASSY C3
[6]
UPPER CASE (OP) ASSY C4
[7]
DIGITAL BOARD ASSY C5
[8]
ANALOG BOARD ASSY C6
[9]
CF SUB BOARD ASSY OPF1
NOTE1:
When removing, be careful not to damage the CONNEC-
TOR or cut/break the WIRE.
When taking out the WIRES, follow the order in the Figure.
When attaching, pay attention in the position of each WIRE.
NOTE2:
When removing, be careful not to damage the CONNEC-
TOR or cut/break the WIRE.
NOTE4a:
When removing, be careful as the COVER (USB) ASSEM-
BLY comes off together.
NOTE4b:
When attaching, be sure to place the FPC WIRE between
the CF SUB BOARD ASSEMBLY and the CABINET
PARTS.
NOTE5a:
Remove the SD Card prior to other removing procedure.
NOTE5b:
When attaching, open the SD COVER, and place the
PLATE into the space between the FPC and the OP
FRAME.
NOTE6a:
Remove the SCREW that tightens the PT. UNIT.
NOTE6b:
When removing, be careful not to cut or break the WIRE.
NOTE6c:
Be careful with the electric shock caused by the CAPACI-
TOR for STROBE.
NOTE6d:
When attaching, be careful with the positions of the PT.
UNIT and the CABINET hole.
NOTE7a:
When removing, peel off the SPACER first, then take out the
CONNECTOR.
NOTE7b:
When removing, take out the WIRE while peeling off the
SPACER.
NOTE7c:
When attaching, be careful with the wiring.
NOTE7d:
When attaching, firmly insert the FPC WIRE of CN7d, and
place the loosened part in the space between the OP
FRAME ASSEMBLY and the DIGITAL BOARD ASSEM-
BLY.
POINT NOTE
3(S1) NOTE1
3(S2) NOTE2
- -
CN4,S4a,S4b,2(L4) NOTE4a,b
3(S5),L5 NOTE5a,b
CN6a,3(S6),CN6b,c NOTE6a,b,c,d
SPACER, CN7a,b,S7,CN7c,d NOTE7a,b,c,d
SPACER,3(S8),CN8 NOTE8a,b,c
2(S9) NOTE9a,b
NOTE8a:
When removing, be careful not to damage the CONNEC-
TOR or cut/break the WIRE.
NOTE8b:
When attaching, refer to the NOTE7b for the handling of the
SPACER, and hold the WIRES with the SPACER.
NOTE8c:
When attaching, place the loosened FPC in the space be-
tween ANALOG BOARD ASSEMBLY and OP BLOCK AS-
SEMBLY.
NOTE9a:
When removing, take out the WIRES prior to other proce-
dure.
NOTE9b:
When attaching, be careful with the wiring.
Destination of connectors
CN.NO. CONNECTOR
CN4 ANALOG CN209
CN6a ANALOG CN205
CN6b ANALOG CN201
CN6c ANALOG CN202
CN7a CF SUB CN9803
CN7b CDS CN5103
CN7c ANALOG CN203
CN7d DIGITAL CN101
CN8 ANALOG CN204
PIN
NO.
OPE1 - 11
STROBE UNIT - 10
MIC - 4
SPEAKER - 2
DIGITAL CN104 51
REG CN308 4/11
DIGITAL CN102 110
CDS CN5102 51
OP BLOCK - 33
(No.YF059)1-29