PHOTO NAVIGATOR” (“Program”) ON YOUR PC. The right to use the Program is granted by Victor Company of Japan, Limited (“JVC”) to You only on the condition that You agree to the following. Should You not agree to the terms hereof, You may not install or use the Program.
Page 3
Should You breach any provision of this Agreement, JVC may terminate this Agreement without giving any notice to You. In this event, JVC may claim against You for any damages caused by Your breach. Should this Agreement be terminated, You must...
Page 4
2.101 (g) consisting unpublished “Commercial Computer Software” as those items are used at FAR part 12.212 and is only licensed to You with the same use rights JVC grants all commercial end users pursuant to the terms of this Agreement.
Page 5
Use only the provided CD-ROM. Never use any other CD-ROM to run this software. Do not attempt to modify this software. Changes or modifications not approved by JVC could void user’s authority to operate the equipment. How to handle a CD-ROM Take care not to soil or scratch the mirror surface (opposite to the printed surface).
Notice for Users Use of this software is authorized according to the terms of the software license. When contacting the nearest JVC office or agency in your country about this software (refer to the JVC Worldwide Service Network at http://www.jvc-victor.co.jp/english/worldmap/index-e.html), please fill out the following and have the appropriate information ready.
System Requirements 8 Digital Photo Navigator The following requirements must be satisfied to connect a camera to a PC and to use Digital Photo Navigator. Free hard disk space Connector Display Miscellaneous ® : Windows Millennium Edition [Me] (pre-installed), ® Windows 2000 Professional [2000] (pre-installed), ®...
Page 8
8 CyberLink DVD Solution The following requirements must be satisfied to use CyberLink DVD Solution. Free hard disk space Connector Display Miscellaneous Supported media DirectX is necessary so that CyberLink DVD Solution works properly and it is automatically installed during CyberLink DVD Solution installation.
Software Installation Follow the procedure described below to install the software. From the [SETUP] screen in step 2, you can install the following drivers or software. Quit any other software you are using. (Check that there are no other application icons on the status bar.) Digital Photo Navigator 1.0 This application is used to organize still images...
Page 10
Click [Next]. [License Agreement] screen appears. Click [Yes]. [Customer Information] screen appears. Confirm your information and click [Next]. It is possible to change the information. [Choose Destination Location] screen appears. Click [Next]. [Setup Type] screen appears. Select the program(s) you want to install, then click [Next].
Install all of the desired software in the same way. To display [SETUP] screen, double-click the CD- ROM icon in the [My Computer] window. NOTES: Even if PowerDirector/PowerProducer/PowerDVD have already been installed on the PC: Video files captured with this camera can only be handled on the provided software.
Viewing the Contents of a Recording Medium Make sure that there is a recording medium in the camera. Set the camera's power switch to the playback mode while pressing down the lock button located on the switch. The camera turns on. Connect the camera to the PC with a USB cable.
Page 13
Folder structure within the recording medium Video files: Stored in the [PRGxxx] folder (where xxx is a number), within the [SD_VIDEO] folder. Still image files: Stored in the [xxxJVCSO] folder (where xxx is a number), within the [DCIM] folder. Voice files: Stored in the [xxxJVCMC] folder (where xxx is a number), within the [DCVC] folder.
Copying Files to the PC Still image, video files and voice files that are stored in a recording medium can be copied to the PC and played back on the PC. Perform the procedure in “Viewing the Contents of a Recording Medium” ( The folders in the recording medium appear.
Files which are not in MPEG2 format Files prepared on any application other than the provided software Edited files which were not produced on a JVC Digital Media Camera Also, be sure to turn off the SVRT function when editing the video files using PowerDirector Express NE.
Page 16
® Windows The [Stop a Hardware device] dialog box appears. Click [OK]. ® Windows 2000/Me: If a message indicating that the device can be safely removed appears, click [OK] and then click [Close]. ® Windows 2000/XP * The model name depends on the connected camera.
User’s Guide/Help/Readme This manual only refers to software installation and PC connection. For more details of each software, refer to its user’s guide/help/Readme. 8 CyberLink DVD Solution Following steps are the example of CyberLink PowerDirector Express NE. Click [Start], go to [All Programs] or [Programs]–...
Subsidiary Information Creating DVDs and Writing Video Files Back to Camera Edit video PowerDirector Express NE Create DVD PowerProducer 2 Gold NE View PowerDVD 5 NE (Main unit) Digital Media Camera Video (recording media) USB transfer Create DVD Create DVD without title with title Select...
Page 19
A brief procedure is presented below for using CyberLink DVD Solution to edit video files that were shot with the camera and create a DVD- Video, transfer the edited videos to the camera, and then play back the videos in the camera. (1) Copy the video files on the media to the PC.
Page 20
(1) Copy the video files on the media to the PC. (2) Start PowerDirector Express NE. (3) Import the copied video files in the PowerDirector Express NE library. (4) Drag and drop the videos that you want to edit from the library to the timeline/ storyboard.
*9 A “defaultxx.mpg” file is created, and the title files are saved. Be sure to remember the file name and storage location. The video can be written back to the camera media. To play back the created video file in the camera, copy the video file into the [EXTMOV] folder in the camera media, and then change the file names to the names below.
Page 22
Drag and drop the videos from the library to the timeline/storyboard in the playback order. If necessary, edit transition or title on the timeline/ storyboard. Click [Produce] button after finish editing. (Example of transition) Select [Produce a Disc], and then click [Next].
Page 23
Click [Start] to create the file. After the completion of video file creation, PowerProducer 2 Gold NE starts automatically. Load a blank DVD media into the recordable DVD drive. Click []] in the [Import/Capture Content] screen of PowerProducer 2 Gold NE. Remove the check mark for [Include Menu] in the [Preview] screen, and then click []].