Error Displays/Messages - Sony CDX-GT620U Operating Instructions Manual

•
20
Radio reception
The stations cannot be received.
The sound is hampered by noises.
o
Connect a power antenna (aerial) control lead (blue)
or accessory power supply lead (red) to the power
supply lead of a car's antenna (aerial) booster (only
when your car has built-in FM/AM antenna (aerial)
in the rear/side glass).
o
Check the connection of the car antenna (aerial).
o
The auto antenna (aerial) will not go up.
- Check the connection of the power antenna
(aerial) control lead.
o
Check the frequency.
o
When the DSO mode is on, the sound is sometimes
hampered by noises.
-Set the DSO mode to "OFF" (page 11).
Preset tuning is not possible.
o
Store the correct frequency in the memory.
o
The broadcast signal is too weak.
Automatic tuning is not possible.
o
Setting of the local seek mode is not correct.
- Tuning stops too frequently:
Set "LOCAL-ON" (page 12).
- Tuning does not stop at a station:
Set "MONO-ON" (page 12).
o
The broadcast signal is too weak.
- Perform manual tuning.
During FM reception, the "ST" indication
flashes.
o
Tune in the frequency accurately.
o
The broadcast signal is too weak.
- Set "MONO-ON" (page 12).
An FM program broadcast in stereo is heard in
monaural.
The unit is in monaural reception mode.
- Set "MONO-OFF" (page 12).
You cannot play back items via a USB HUB.
This unit cannot recognize USB devices via a USB
HUB.
Cannot play back items.
A USB device does not work.
-+
Reconnect it.
The USB device takes longer to play back.
The USB device contains files with a complicated tree
structure.
A beep sounds.
During playback, the USB device has been
disconnected.
-+
Before disconnecting a USB device, make sure to
stop playback first for data protection.
The sound is intermittent.
The sound may be intermittent at a high-bit-rate of
more than 320 kbps.
Error displays/Messages
CHECKING
The unit is confirming the connection of a USB device.
- Wait until confirming the connection is finished.
ERROR
o
The disc is dirty or inserted upside down.
-Clean or insert the disc correctly.
o
A blank disc has been inserted.
o
The disc cannot play due to a problem.
- Insert another disc.
o
USB device was not automatically recognized.
- Reconnect it again.
o
Press
~
to remove the disc.
FAILURE
The connection of speakers/amplifiers is incorrect.
- See the installation/connections manual of this
model to check the connection.
HUB NO SUPRT
USB HUB is not supported on this unit.
L. SEEK +/-
The local seek mode is on during automatic tuning .
NO DEV (No Device)
(SOURCE)
is selected without a USB device
connected. A USB device or a USB cable has been
disconnected during playback.
- Be sure to connect a USB device and USB cable.
NO INFO
Text information is not written in the MP3IWMAI
AAC file.
NO MUSIC
The disc/USB device does not contain a music file.
- Insert a music CD in this unit.
-
Connect a USB device with a music file in it.
NO NAME
A disc/album/track name is not written in the track.
NO TRACK
The selected item in the USB device does not contain
an album/track.
OFFSET
There may be an internal malfunction.
- Check the connection. If the error indication
remains on in the display, consult your nearest
Sony dealer.
OVERLOAD
USB device is overloaded.
- Disconnect the USB device, then change the source
by pressing
(SOURCE).
-Indicates that the USB device is out of order, or an
unsupported device is connected.
READ
The unit is reading all track and album information on
the disc/USB device.
- Wait until reading is complete and playback starts
automatically. Depending on the disclUSB device
structure, it may take more than a minute.
RESET
The CD unit cannot be operated due to a problem.
- Press the RESET button (page 4).