Vermont Castings VWDV70 Installation And Operating Instructions Manual page 43

touch screen reMote controL operatIon
the Room temperature. There is no manual flame height
adjustment. The fan speed will also automatically adjust
if turned on.
note: there will a 10 second delay for the flame adjust-
ment when the fireplace is turned on.
1. When Set Temp. is 3° F or higher than Room Temp.,
flame height will be on High.
2. When Set Temp. is 2° F higher than Room Temp.,
flame height will be on Medium.
3. When Set Temp. is 1° F higher than Room Temp.,
flame height will be on Low.
4. When Set Temp. is equal to Room Temp., flame height
does not change (stays on low).
5. When Set Temp. is lower than Room Temp., the fire-
place will be shut off.
6. When Set Temp. is 1° F higher than Room Temp.,
again the flame height will be on Low.
7. the fan speed follows the flame height, if the fan is
turned on.
To exit Smart Mode and shut off the fireplace;
a. push and hold the THERMO buttons for 3 sec-
onds, Or
b. press the OFF button, Or
c. slide down on the arrow buttons.
To shut off the Smart Mode option and return to regular
thermostat mode, press and hold the THERMO button
and the ON/UP button at the same time for 3 seconds
again.
Blower speed control (not used with VWDV70)
Figure 67
note: Blower will only work with
flame on.
The blower speed control function
is used to adjust the speed of the
blower connected to the Signature
Command System. There are four
speed levels, Off, Low, Medium,
High.
1. Press the FAN button to enter
the blower speed control mode.
The fan icon will start flashing.
2. Press the ON/up and OFF/
down button to increase/de-
crease the blower speed.
3. Press the fan button again to confirm the speed set-
ting. If the fireplace is on, the blower speed will take
effect right away; if the fireplace is off, the receiver will
remember this setting and the blower is still off (see
blower On Delay and Off Delay in the next section).
4. After the signal is sent, the ON/up and OFF/down but-
tons become flame height controller again.
20303735
5. When the fan button is flashing, slide up and down on
6. If the blower is turned on using the FAN button, the
Blower on Delay time and off Delay time setup
(not used with VWDV70)
Figure 68
1. Hold the FAN button for 3 sec-
2. When the first number is flash-
3. Press the OFF/down button
4. When the second number is flashing, use the ON/up
5. Press the OFF/down button again to finish the setup
6. The default settings are 5 minutes for the On Delay
Light Brightness control
Figure 69
The light brightness control func-
tion is used to adjust the bright-
ness of the light bulbs connected
to the AC module on the Signa-
ture Command System. There
are four light brightness levels
defined: Off, Low, Medium, High
1. Press the LIGHT button to en-
Figure 67
FP2655
2. Press the On/up and OFF/
blower speed control
3. Press the light button again to confirm the setting. The
4. After the signal is sent, the On/up and Off/down but-
VWDV70 Series Gas Fireplace
the arrow buttons will turn the blower speed to High
or Off directly without pressing the fan button again to
confirm.
blower speed will adjust automatically when using
Smart Mode (See Smart Mode section).
onds until two numbers ap-
pear on the LCD screen. The
left number is blower On Delay
and the right number is blower
Off Delay Time.
ing, use the ON/up button to
set the desired On Delay Time
from 0 to 15 min.
to jump to the Off Delay Time
setup.
button again to set the desired Off Delay Time from 0
to 15 min.
and the new settings will be transmitted to the receiv-
er.
Time and 8 minutes for the Off Delay Time, as shown.
ter the light brightness control
mode. The LIGHT icon will
start flashing.
down buttons to increase/de-
crease the light brightness
(Off-Low-Medium-High).
new setting will be transmitted to the receiver.
tons become flame height controller again.
Figure 68
FP2656
blower delay setup
Figure 69
FP2657
Light bright control
43