Sony HBD-E370 Service Manual page 26

HBD-E370/E470/E570/E870/T57
Screen 12: *FA Mode Test (Not Used)
(Screen 12)
FA Mode Test
[1] Enter Repeat FA mode
Repeat number: 0000
[2] Save FE log to USB
Not used for the servicing.
Press the [RETURN] button if having entered this mode.
CONFIRMATION ITEM
1. Playback Operation Confi rmation
1-1. Test Disc
Part No. Description
J-6090-199-A BLX-104
J-6090-200-A BLX-204
J-2501-307-A CD (HLX-A1)
J-2501-305-A HLX-513
J-2501-306-A HLX-514
J-6090-077-A HLX-506
J-6090-078-A HLX-507
Note: Refer to the service manual of BDP-BX1/S350 (Part No. 9-883-
989-1[]) (page 1-3 to 1-14E) for the use of BLX-104/204.
Operation and Display:
1. BLX-104
Procedure:
1. Select 23.976Hz/1080p.
2. Play "4.Motion picture".
3. Check whether player can play back or not.
4. Check each outputs.
Video:
Composite/S Video/component/HDMI.
Audio:
Speaker out.
* When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz)
can use instead of 1080/24p.
However this is temporary correspondence.
* When the output of HDMI is 1080p, the signal of Composite/S
Video/Component are not output.
It is necessary to lower the output of HDMI to 1080i or less.
2. BLX-204
Procedure:
1. Select 1080i (59.94Hz or 50Hz).
2. Play "4.Motion picture".
3. Check whether player can play back or not.
(Check the picture and sound output)
26
3. CD (HLX-A1)
Procedure:
Check whether player can play back or not.
(Check the sound output)
4. HLX-513/514 (NTSC), HLX-506/507 (PAL)
Procedure:
1. After displayed Main Menu, select "1.Video Signal".
2. Play "1.Color bar 100%".
3. Return to Menu.
4. Play "Demonstration 4:3" or "Demonstration 16:9".
1-2. Playback operation confi rmation
Confi rm operation in each signal/output mode of test disc (BLX-
104/204) according to the content of the repair.
Note: "AV Sync." doesn't operate.
2. Networking Confi rmation
Confi rm it according to the following procedure when you confi rm
the connection of the network.
Note: Do not execute "Network Connection Diagnostics" of "Network
Procedure:
Layer
1. Connect the router with the set with LAN cable.
Single Layer
2. Turn on the power of the set and the router.
Dual Layer
3. Press the [HOME] button on the remote commander, and the
4. Select "Setup" → "Network Settings" → "Internet Settings",
Single Layer (NTSC)
Dual Layer (NTSC)
5. Select "View Networks Status" and press the [3] button on the
Single Layer (PAL)
Dual Layer (PAL)
6. Confi rm IP address are displayed in "IP Address", "Subnet
(Check the picture and sound output)
(Check the picture and sound output)
Settings" of the home menu with only the router connected.
home menu is displayed.
and press the [3] button on the remote commander.
remote commander.
Mask" and "Default Gateway".
Physical Connection:
Internet Access:
IP Address Setting:
IP Address:
Subnet Mask:
Default Gateway:
DNS Settings:
Primary DNS:
Secondary DNS:
MAC Address:
XXXX
XXXX
XXXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX