Advertisement
GENERAL SAFETY INSTRUCTIONS
FOR POWER TOOLS
1. KNOW YOUR TOOL
Read and understand the owners manual and labels affixed to the tool. Learn its
application and limitations as well as its specific potential hazards.
2. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents. Make sure the floor is clean and not
slippery due to wax and sawdust build-up.
3. AVOID DANGEROUS ENVIRONMENT.
Don't use power tools in damp or wet locations or expose them to rain. Keep work
area well lit and provide adequate surrounding work space.
4. KEEP CHILDREN AWAY.
All visitors should be kept a safe distance from work area.
5. MAKE WORKSHOP CHILD-PROOF.
Use padlocks, master switches or remove starter keys.
6. USE PROPER SPEED.
A tool will do a better and safer job when operated at the proper speed.
7. USE RIGHT TOOL.
Don't force the tool or the attachment to do a job for which it was not designed.
8. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings, watch) because they
could get caught in moving parts. Non-slip footwear is recommended. Wear
protective hair covering to contain long hair. Roll up long sleeves above the elbows.
9. ALWAYS WEAR SAFETY GLASSES.
Always wear safety glasses (ANSI Z87.1). Everyday eyeglasses only have impact
resistant lenses, they are NOT safety glasses. Also use a face or dust mask if cutting
operation is dusty.
10. MAINTAIN TOOL WITH CARE.
Keep tools clean for best and safest performance. Follow instructions if any for
lubricating and changing accessories.
11. DISCONNECT TOOLS.
Before servicing, when changing accessories or attachments.
12. AVOID ACCIDENTAL STARTING.
Make sure the switch is in the ''OFF'' position before plugging in.
13. CHECK DAMAGED PARTS.
Before further use of the tool, a guard or other parts that are damaged should be
carefully checked to ensure that they will operate properly and perform their intended
function. Check for alignment of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other parts that are damaged
should be properly repaired or replaced.
14. NEVER LEAVE MACHINE RUNNING UNATTENDED.
Turn power ''OFF''. Don't leave any tool running until it comes to a complete stop.
ELECTRICAL INFORMATION
& ASSEMBLY
Warning: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood
by the operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.
Note: Performance of this tool (if powered by line voltage) may vary depending on
variations in local line voltage. Extension cord usage may also affect tool performance.
VOLTAGE WARNING
Before connecting the tool to a power source (receptacle, outlet, ect.) be sure the voltage
supplied is about the same as that specified on the nameplate of the tool. If one says 120V
and the other says 115V then there will be no complications. Never try to plug a 115V tool
into a 230V outlet, or the other way around. The plug and outlet have completely different
shapes. This is because a power source with a voltage greater than that specified on the
tool can result in SERIOUS INJURY to the user, as well as damage to the tool. If in doubt,
DO NOT PLUG IN THE TOOL.
EXTENSION CORDS
Your tool has a polarized, two-prong plug. Do not alter the plug in any way. Only use
rounded jacket extension cords listed by the Underwriters Laboratories (UL). Improper
use of extension cords may cause inefficient operation of your tool which can result in
overheating. Be sure your extension cord is rated to allow sufficient current flow to the
motor. If you are using the tool outdoors, use an extension cord rated for outdoor use
(signified by "WA" on the jacket).
The extension cord must have a minimum wire size depending on the amperage of the tool
and the length of the extension cord. This size is determined by its AWG (American Wire
Gauge) rating. The smaller the gauge, the greater the cable's capacity. The amount of cords
used does not matter: Total length determines the minimum AWG rating. Every cord must
meet the AWG rating. Use the chart below to determine what AWG rating is required for
your situation. Cord length is rated in feet.
LENGTH OF
CONDUCTOR
0-25 FEET
26-50 FEET
51-100 FEET
ASSEMBLY
Your Random Orbit Sander comes almost fully assembled, only the dust bag must be
assembled to the dust port. For installation of sandpaper and operating instructions, please
refer to the operation section of this manual.
WIRE SIZE REQUIRED
(AMERICAN WIRE GAUGE)
120V LINES
NO.16
NO.14
NO.12
Advertisement
