Table of Contents
Advertisement
Quick Links
SET UP AND OPERATING INSTRUCTIONS
Distributed exclusively by Harbor Freight Tools
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
©
Copyright
2008 by Harbor Freight Tools
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 11h
L.E.D. AIR ANGLE
DIE GRINDER
3491 Mission Oaks Blvd., Camarillo, CA 93011
®
. All rights reserved. No portion of this manual or any artwork
99612
®
.
Advertisement
Table of Contents
Related Manuals for Central Pneumatic 99612
Summary of Contents for Central Pneumatic 99612
- Page 1 L.E.D. AIR ANGLE DIE GRINDER 99612 SET UP AND OPERATING INSTRUCTIONS ® Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury.
-
Page 2: Personal Safety
Die Grinder. Do not minor or moderate injury. use while tired or under the influ- SKU 99612 For technical questions, please call 1-800-444-3353. Page 2... -
Page 3: Control Lever
Risk of Electric Shock. This tool with sharp cutting edges and clean is not provided with an insulated grinding surfaces reduces the risk of gripping surface. Contact with a binding and is easier to control. SKU 99612 For technical questions, please call 1-800-444-3353. Page 3... -
Page 4: Symbol Definitions
Respiratory Injury. Wear NIOSH- air source has been adjusted to the approved dust mask/respirator. rated air pressure or within the rated Chart continued in next column. air-pressure range. SKU 99612 For technical questions, please call 1-800-444-3353. Page 4... -
Page 5: Valve
To reduce the risk of approved safety equipment, such as vibration-related injury: those dust masks that are specially SKU 99612 For technical questions, please call 1-800-444-3353. Page 5... -
Page 6: Speed
Control Lever (4) To reduce vibration, maintain tool as Clamp Nut (32) explained in this manual. If abnormal vibration occurs, stop immediately. SAVE THESE INSTRUCTIONS. SKU 99612 For technical questions, please call 1-800-444-3353. Page 6... -
Page 7: Air Supply
INJURY FROM ACCIDENTAL OPERATION: Do not install a female quick coupler on the tool. Such a coupler contains an air valve that will allow the air tool to retain pressure and SKU 99612 For technical questions, please call 1-800-444-3353. Page 7... -
Page 8: Operating Instructions
However, it is a able at Harbor Freight Tools. good safety measure to attempt to discharge the tool in a safe fashion after disconnecting to ensure that the SKU 99612 For technical questions, please call 1-800-444-3353. Page 8... - Page 9 Insert the shaft of the grinding attach- or clamps (not included) to prevent ment (not supplied) through the flared movement while working. end of the Collet (31). See Figure 3. SKU 99612 For technical questions, please call 1-800-444-3353. Page 9...
-
Page 10: General Operating Instructions
(CFM) and increase the pressure (PSI) output of the regulator up to the maximum air pressure rating of this tool (90PSI). SKU 99612 For technical questions, please call 1-800-444-3353. Page 10... -
Page 11: Vanes
Turn the Die Grinder over and the explosion. three Batteries (40) will drop out of the Battery Compartment. Replace the used Batteries with new, fresh Batteries identical to the Batter- ies that were removed. Use caution SKU 99612 For technical questions, please call 1-800-444-3353. Page 11... -
Page 12: Table Of Contents
O-Ring instead. Wrench 11MM Note: Some parts are listed and shown for Wrench 17MM illustration purposes only, and are not Switch (ON/OFF) available individually as replacement parts. LED Seat Batteries SKU 99612 For technical questions, please call 1-800-444-3353. Page 12... -
Page 13: Assembly Diagram
ASSEMBLY DIAGRAM SKU 99612 For technical questions, please call 1-800-444-3353. Page 13... - Page 14 This warranty gives you specific legal rights and you may also have other rights which vary from state to state. SKU 99612 For technical questions, please call 1-800-444-3353. Page 14...
Need help?
Do you have a question about the 99612 and is the answer not in the manual?
Questions and answers