Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for KALATEL KTD-400
Summary of Contents for KALATEL KTD-400
- Page 1 KTD-400 Controller Keypad Installation and Operation Manual...
- Page 2 Kalatel, a division of Interlogix, Inc. The information contained in this document is subject to change without notice. Kalatel, in keeping pace with technological advances, is a company of product innovation. Therefore, it is difficult to ensure that all information provided is entirely accurate and up-to-date.
-
Page 3: Table Of Contents
Monitor Selection ........................24 Camera Selection ........................24 Engaging Auto Focus on CyberDomes ..................24 Finding a Preset ..........................24 Preset Tours ..........................24 Camera Sequencing ........................24 Setting Electronic Auto Pan Limits for Kalatel Domes ..............25 Video Alarms ..........................25 Clearing Alarms ...........................25 1034790D / January 2001... - Page 4 KTD-400 Controller Keypad Installation and Operation Manual Multiplexer Operations ........................25 Switching to Multiplexer Control Mode ..................25 Selecting an Active Multiplexer ....................26 Calling up a Video Input on an Active Multiplexer ..............26 Switching a Multiplexer to Live Video ..................26 Placing the Active Multiplexer in the Camera Sequence Mode ..........26 Viewing VCR Output or Playback ....................26...
-
Page 5: Introduction
This manual covers installation and operation instructions for a KTD-400 series keypad. Designed ntroduction for use in a Digiplex™ system (see Figure 1), the KTD-400 can address and control 512 pan/tilt/zoom receiver sites, operate a matrix switcher with 64 monitor outputs, and address and select views from as many as 64 multiplexers and VCRs. - Page 6 KTD-400 Controller Keypad Installation and Operation Manual 1034790D / January 2001...
-
Page 7: Installation
Do not connect power to the unit before all installation steps have been completed. Do not connect directly to a telecommunication network. The KTD-400 contains a DIP switch that is used to select mode of operation choices as Setting the DIP Switch shown in Table 1. -
Page 8: Wiring Connections
KTD-400 Controller Keypad Installation and Operation Manual Wiring Connections The KTD-400 comes with a 6-foot cable that attaches to a modular phone box. All external connections are made in the phone box. For the KTD-300R, connections are made to the removable terminal strip located on the rear of the unit. - Page 9 Figure 6: KTD-300R terminal strip connections with KTS-41A control Powering Up After all the connections are made, the KTD-400 or KTD-300R is ready for operation. Plug the 12VDC wall transformer into a power outlet. The LCD window will briefly display keypad setting information, and then it will enter the operating mode.
- Page 10 KTD-400 Controller Keypad Installation and Operation Manual 1034790D / January 2001...
-
Page 11: Programming
KTD-400 Controller Keypad Installation and Operation Manual Programming This section provides instructions for programming the KTD-400 keypad and for using it to program other components in the Digiplex system, including: • Pan/Tilt/Zoom Receiver Programming • Video Switcher Programming • Alarm Interface Programming •... - Page 12 KTD-400 Controller Keypad Installation and Operation Manual Clear Keypad Memory Figure 10: Clear Memory Display CLEAR MEMORY? 0=NO 1=YES SEQ=EXIT Step 2) The CLEAR MEMORY option will erase all data in the controller keypad’s nonvolatile memory and reload factory default values. To clear the controller keypad’s memory, press...
- Page 13 KTD-400 Controller Keypad Installation and Operation Manual Step 6) This menu is used to deny or permit the controller keypad’s access to certain monitors. Press to deny access or to permit access. After each selection, the next monitor number will appear. The keys can be used to move between monitors.
- Page 14 KTD-400 Controller Keypad Installation and Operation Manual VCR Enabled Figure 18: VCR Enabled Display VCR 01 ACC=YES 0=NO 1=YES SEQ=NEXT Step 10) This menu determines which VCRs can be enabled (accessed) from the keypad. This menu will only come up if at least one VCR is in the system (see Step 4). To enable a VCR, press .
-
Page 15: System Component Programming
KTD-400 Controller Keypad Installation and Operation Manual System Component Once the KTD-400 keypad programming has been completed, it can be used to program Programming Digiplex system components. To program system components, begin at the normal operating display and proceed as follows:... -
Page 16: P/T/Z Receiver Programming
Each receiver offers mode of operation choices, many of which can be programmed using Programming a KTD-400 series keypad. It can also store preset position information if applicable. The following steps outline the receiver setup procedure. Beginning at the normal operating... - Page 17 KTD-400 Controller Keypad Installation and Operation Manual Pan Cycle Figure 29: Pan Cycle Display PAN CYCL? 0=0% 1=50% 2=100% 3=RDM SEQ=NXT Step 5) If the pan/tilt receiver is to auto pan, enter one of the four following choices listed in the chart below:...
- Page 18 CLR RCVR MEM? 000 0=NO 1=YES SEQ=NEXT Step 12) With the CLR RCV MEM option, the KTD-400 will instruct the P/T/Z receiver to erase all data in its nonvolatile memory and reload factory default values. To clear the receiver’s memory, press .
-
Page 19: Setting Electronic Auto Pan Limits
Step 14) Repeat steps 3 - 13 for each receiver in the system. Setting Electronic Auto Pan Limits for Kalatel Domes To set the electronic auto pan limits on Kalatel dome receivers, first position the dome at the limit. While holding down the... - Page 20 KTD-400 Controller Keypad Installation and Operation Manual Step 5) Assign a preset position number (one or two digit depending on the receiver type and largest preset number) using one of the two methods described below: Method 1: If the position is not to be included in the preset tour, enter the preset number by using the number key(s).
-
Page 21: Operation
KTD-400 Controller Keypad Installation and Operation Manual Operation A KTD-400 series keypad can address and control 512 P/T/Z receiver sites, operate a matrix switcher with 64 monitor outputs, address and select views from 64 multiplexers, and control 64 VCRs. It can also be used to control a KTS-41 Mini-Matrix switcher. -
Page 22: Key Functions
KTD-400 Controller Keypad Installation and Operation Manual Key Functions Site Select Keys Used for camera and monitor selection in Digiplex operation mode, or camera and multiplexer selection in multiplexer operation. Also used for preset position selection when applicable. Refreshes alphanumeric display on the selected monitor. Also used to clear clear infinite alarms using numerical keys. -
Page 23: Vcr Control Keys
KTD-400 Controller Keypad Installation and Operation Manual live Used to view the live video inputs in any of the display modes; also used during setup of motion detection areas Selects VCR output for monitoring during taping or VCR input for viewing during playback. -
Page 24: Keypad Operation
KTD-400 Controller Keypad Installation and Operation Manual Keypad Operation When power is first supplied to a KTD-400 series keypad, the LCD display will briefly display the Kalatel name and then appear as shown below: Figure 44: KTD-400’s Normal Operating Display... -
Page 25: Setting Electronic Auto Pan Limits For Kalatel Domes
Setting Electronic Auto Pan Limits for Kalatel Domes To set the electronic auto pan limits on Kalatel dome receivers, first position the dome at the limit. While holding down the keys, press the arrow keys in the direction of the... -
Page 26: Selecting An Active Multiplexer
Refer to the installation and operation documentation provided with the multiplexer to determine available views. key toggles the KTD-400 between normal operation mode, multiplexer operation VCR Operation mode mode, and VCR operation mode. -
Page 27: Technical Support
Three-Year Warranty* Kalatel, a division of Interlogix, Inc. warrants its products for three years from the date of factory shipment. The war- ranty covers defects in materials and workmanship, and does not cover equipment that has been abused, damaged, or modified.