Table of Contents
Related Manuals for CDA FW971
Summary of Contents for CDA FW971
- Page 1 Manual for Installation, Use and Maintenance Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu...
- Page 2 Under no circumstances should any external covers be removed for servicing or maintenance except by suitably qualified personnel. Appliance information: Please enter the details on the appliance rating plate below for reference, to assist CDA Customer Care in the event of a fault with your appliance and to register your appliance for guarantee purposes. Appliance Model...
-
Page 3: Before First Use
Important Never store inflammable or explosive items and strong corrosive acids or alkalis in the appliance. This is a household appliance, which is produced in accordance with the national standard. It is intended for food storage only, not for storage of blood, medicine and biological products. To prevent risk of fire, keep the appliance away from petrol or any other inflammables. - Page 4 Fridge • Never put liquids in the refrigerator uncovered. • Never put hot foods in the refrigerator. Warm food should be allowed to cool to room temperature before being put into the refrigerator. • Nothing should rest against the rear wall of the refrigerator, as this will cause frost and possible condensation problems which will be difficult to remove.
- Page 5 Storage The fridge section is for short term food storage. Although the temperature can be maintained between 2~8˚ C , extended periods of food storage is not recommended. As the cold air circulates within the fridge, the temperature can vary between the different sections.
-
Page 6: Control Panel
Control panel High High REF. FRZ. S.Cool S.Cool fig. 3 A. Power button To put the fridge freezer on standby press and hold the power button for approximately three seconds. To start the compressor working again, press and hold the power button for approximately three seconds. B. -
Page 7: Care And Cleaning
Care and cleaning Always disconnect the appliance from the power supply before any cleaning or maintenance. Both fridge and freezer are frost free and as such this appliance is designed not to require defrosting. The fridge and freezer sections should be cleaned using a solution of bicarbonate of soda and lukewarm water. Do not use abrasive products or detergents. -
Page 8: Troubleshooting
Troubleshooting If you have any problems with your appliance, you should check the troubleshooting prior to calling CDA Customer Care to prevent unnecessary service calls and potential cost. If the appliance is not working • Check there is power to the appliance. -
Page 9: Installation And Ventilation
Installation And Ventilation 200 cm This appliance must never be installed close to heat sources, e.g. heating elements, cookers or in damp places. Introduction: The information provided in this document shows the cabinet ventilation requirements and the installation steps to fit the product into the housing unit: Ventilation: It is vitally important that adequate ventilation is provided to allow the refrigeration system to cool. - Page 10 Fitting the product into the cabinet 1. Remove the gasket protection pieces: The gasket protectors prevent excessive seal compression during transport and are required during the installation process. Remove the gasket protector from each door (fig 5) and proceed with the installation. Cover caps are provided to fill the hole;...
- Page 11 8. Fitting the bottom cabinet fixing bracket: A sliding bracket is provided to secure the non-hinge side of the product to the cabinet. This is fitted to the bottom of the product using two machine screws, as shown below. A guide piece is also provided to ensure Guide piece simply the unit is aligned when installed.
- Page 12 Fitting the cabinet fascia doors Upper fixing plate (Dismantling) First, fit the upper fascia by following the steps below. After fitting the upper fascia in the correct position, use the lower edge of the upper fascia as a guide for positioning the lower fascia (A distance between the two fascias when installed is normally between 2 and 4mm) and fit the lower fascia.
- Page 13 Adjusting the position of the fascia doors The position of the fascia doors can be made in all 3 axes by following the guide shown below (figure 18). If the range of adjustment detailed below is not enough then the refrigerator is not located correctly in the cabinet and/ or the upper fascia fixing plates are incorrectly positioned.
- Page 14 Fitting the trims and cover pieces 1. Open the door and lift out the decorative covers (marked ‘a’) in figure 20 2. Remove the position guides (d), turn them round so that the lip at the top faces outwards and insert them into the slots shown in the image (e);...
-
Page 15: Electrical Information
Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. - Page 16 Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu...