Menu Tree - Traxxas XO-1 64077 Owner's Manual

MENU TREE

The menu tree below shows how to navigate through
the TQi transmitter's various settings and functions.
Press and hold MENU to enter the menu tree, and use
the following commands to navigate through the menu
and select options.
MENU: When you enter a menu, you always start at the
top. Press MENU to move down the menu tree.
When you reach the bottom of the tree, pressing
MENU again will return you to the top.
SET: Press SET to move across the menu tree and select
options. When an option is committed to the
transmitter's memory, the status LED will rapidly
blink green.
BACK: Press both MENU and SET to go back one level in
the menu tree.
EXIT: Press and hold MENU to exit programming.
Your selected options will be saved.
ECHO: Press and hold SET to activate the "echo" function.
Echo will "play back" your current position on the
Menu Tree, should you lose your place. For example:
If your current position is Steering Channel End
Points, holding SET will cause the LED to blink green
twice, green once, and then red three times. Echo
will not alter your adjustments or change your
position in the programming sequence.
Below is an example of how to access a function in the menu
tree. In the example, the user is setting the Multi-Function knob
to be a steering Dual Rate control.
To set the Multi-Function knob to control STEERING DUAL RATE (%):
1. Switch the transmitter on
2. Press and hold MENU until the green LED lights. It will blink in single
intervals.
3. Press SET. The red LED will blink in single intervals to indicate Steering
Dual Rate has been selected.
4. Press MENU twice. The red LED will blink three times repeatedly to
indicate Steering Percentage has been selected.
5. Press SET to select. The green LED will blink 8 times fast to indicate
successful selection.
6. Press and hold MENU to return to driving mode.
Restoring Factory Defaults:
Transmitter Hold both Transmitter Release MENU and SET
OFF MENU and SET ON
Enter Programming
Press and hold
MENU for 3 seconds
1
Multi-Function Knob
One Blink Green
Press
MENU
2
Channel Setup
Two Blinks Green
Press
MENU
3
Mode Selection
Three Blinks Green
Press
MENU
4
Traxxas Link
Four Blinks Green
Press MENU once. The
transmitter LED will blink will turn solid green. Transmitter
red LED blinks
red twice repeatedly.
Press MENU to move through options.
Press SET to select an option.
1
Steering Sensitivity (Expo)
One Blink Red
2
Throttle Sensitivity (Expo)
Two Blinks Red
3
Steering % (Dual Rate)
Three Blinks Red
4
Braking %
Four Blinks Red
Press
5
Throttle Trim
SET
Five Blinks Red
6
Knob Disabled
Six Blinks Red
1
Steering (Channel 1)
Press
SET
One Blink Green
Press
MENU
2
Throttle (Channel 2)
Two Blinks Green
Press SET to select an option.
1
Electric
Press
SET
One Blink Red
Press
MENU
2
Nitro
Two Blinks Red
1
Model Locking
Press
SET
One Blink Green
Press
MENU
Press SET to clear settings. LED
2
is restored to default Delete Model
Two Blinks Green
TQ ADVANCED TUNING GUIDE
i
Note: The transmitter is "live" during programming
so you can test the settings real time without having
to exit the menu tree.
Press MENU to move through options.
Press SET to select an option.
1
Servo Reversing
Press SET to reverse
servo direction.
One Blink Red
2
Sub-Trim
Use knob to adjust
sub-trim. Press SET to save.
Two Blinks Red
3
End Points Use steering wheel to
adjust. Turn right to desired
Three Blinks Red
end point, press set to save.
Turn left to desired endpoint and press set to save.
To reset max throw: Let go of controls and press SET.
Press
4
SET Reset End Points
Press SET to restore
factory default endpoints.
Four Blinks Red
1
Press
Servo Reversing
Press SET to reverse
SET
servo direction.
One Blink Red
2
Sub-Trim
Use knob to adjust sub-
trim. Press SET to save.
Two Blinks Red
3
End Points Use trigger to adjust. Pull
back to desired end point,
Three Blinks Red
press set to save. Push
forward to desired endpoint and press set to save.
To reset max throw: Let go of controls and press SET.
4
Reset End Points
Press SET to restore
Four Blinks Red factory default endpoints.
1
Press Unlock
SET
One Blink Red
2
Lock
Two Blinks Red
3
Unlock All
Three Blinks Red
1
Press C onfirm Deletion
SET
One Blink Red
XO-1 33
•