Led Codes - Traxxas XO-1 64077 Owner's Manual

Throttle Trim Seek Mode
When the Multi-Function knob is
set to throttle trim, the transmitter
remembers the throttle trim
setting. If the throttle trim knob is
moved from the original setting
while the transmitter is off, or while
the transmitter was used to control
another model, the transmitter
ignores the actual position of
the trim knob. This prevents the
model from accidentally running
away. The LED on the face of the
transmitter will rapidly blink green
and the throttle trim knob (Multi-
Function knob) will not adjust the
trim until it is moved back to its
original position saved in memory.
To restore throttle trim control,
simply turn the Multi-Function
knob either direction until the LED
stops blinking.
Failsafe
Your Traxxas radio system is
equipped with a built-in failsafe
function that returns the throttle
to its last saved neutral position in
the event of a signal loss. The LED
on the transmitter and the receiver
will rapidly flash red.
32 XO-1
•
TQ ADVANCED TUNING GUIDE
i
throttle/brake travel (on the throttle channel). This allows you to fine-
tune the servo settings to prevent binding caused by the servo moving
steering or throttle linkages (in the case of a nitro car) farther than their
mechanical limits. The end point adjustment settings you select will
represent what you wish to be the servo's maximum travel; the Steering
Percentage or Braking Percentage functions will not override the End
Point settings.
Steering and Throttle Sub-Trim
The Sub-Trim function is used to precisely set the neutral point of the
steering or throttle servo in the event that simply setting the trim knob
to "zero" does not completely center the servo. When selected, Sub-Trim
allows finer adjustment to the servo output shaft's position for precise
setting of the neutral point. Always set the Steering Trim knob to zero
before making final adjustment (if required) using Sub-Trim. If Throttle
Trim has been previously adjusted, the Throttle Trim will need to be
reprogrammed to "zero" before making final adjustment using Sub-Trim.
Setting Lock
Once you've adjusted all of these settings the way you like them, you
may want to disable the Multi-Function knob so none of your settings
TRANSMITTER LED CODES
LED Color / Pattern
Solid green
Slow red (0.5 sec on / 0.5 sec off)
Flashing fast green (0.1 sec on / 0.15 sec off)
Flashing medium red (0.25 sec on / 0.25 sec off)
Flashing fast red (0.125 sec on / 0.125 sec off)
Programming Patterns
or
Counts out number (green or red) then pauses
8
x
Fast green 8 times
x 8
Fast red 8 times
RECEIVER LED CODES
LED Color / Pattern
Solid green
Slow red (0.5 sec on / 0.5 sec off)
Flashing fast red (0.125 sec on / 0.125 sec off)
can be changed. This is especially handy if you operate multiple vehicles
with a single transmitter via Traxxas Link
Multiple Settings and the Multi-Function Knob
It is important to note that settings made with the Multi-Function knob
are "overlaid" on top of each other. For example, if you assign the Multi-
Function to adjust Steering Percentage and set it for 50%, then reassign
the knob to control Steering Sensitivity, the transmitter will "remember"
the Steering Percentage setting. Adjustments you make to Steering
Sensitivity will be applied to the 50% steering throw setting you selected
previously. Likewise, setting the Multi-Function knob to "disabled" will
prevent the knob from making further adjustments, but the last setting
of the Multi-Function knob will still apply.
TRAXXAS LINK MODULE LED CODES
LED Color / Pattern
Blue LED off
Slow blue
(0.5 sec on / 0.5 sec off)
Solid blue
Name Notes
Normal Driving Mode See page 15 for information on how to use your transmitter controls.
Binding See page 16 for more information on binding.
Turn the Multi-Function knob right or left until the LED stops flashing.
Throttle Trim Seek Mode
See sidebar for more information.
Low Battery Alarm Put new batteries in the transmitter. See page 13 for more information.
Transmitter and receiver are no longer bound. Turn the system off and then back on to
Link Failure / Error resume normal operation. Find source of the link failure (ie out of range, low batteries,
damaged antenna).
Current menu position See Menu Tree for more information.
Menu setting accepted (on SET)
Menu SET invalid User error such as trying to delete a locked model.
Name Notes
Normal Driving Mode See page 15 for information on how to use your transmitter controls.
Binding See page 16 for more information on binding.
Consistent Low-Voltage in the receiver triggers Fail-Safe so there is enough power to
Fail-Safe / Low-Voltage Detect
center the throttle servo before it completely loses power.
™ Model Memory.
Name Notes
Traxxas Link App is not running on
Connecting mode
a paired device.
See above for information on pairing
Pairing mode
the module with Traxxas Link App.
See page 12 for information on how
Connected
to use your transmitter controls.