Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Traxxas Maxx
Summary of Contents for Traxxas Maxx
- Page 1 MODEL 89076-4 OWNER’S MANUAL...
- Page 2 Even if you are an experienced RC enthusiast, it’s important to read and follow the procedures in this manual. DRIVING YOUR MODEL Thank you again for going with Traxxas. We work hard every day BASIC TUNING to assure you the highest level of customer satisfaction possible.
-
Page 3: Before You Proceed
Technical support is available Monday through Friday from 8:30am the model carefully. If for some reason you decide it is not what to 9:00pm central time. Technical assistance is also available at Traxxas. Internet you wanted, then do not continue any further. Your hobby dealer com. -
Page 4: Safety Precautions
SAFETY PRECAUTIONS All of us at Traxxas want you to safely enjoy your new model. • Disconnect the Battery: Always disconnect the battery from the Operate your model sensibly and with care, and it will be exciting, speed control when not in use. - Page 5 • DO NOT disassemble, crush, short circuit, or expose the batteries to associated with LiPo battery use. Traxxas does not recommend flame or other source of ignition. that anyone under the age of 14 use or handle LiPo battery packs without the supervision of a knowledgeable and responsible •...
-
Page 6: Tools, Supplies And Required Equipment
*Battery and charger style is subject to change and may vary from images. REMOVING AND INSTALLING THE BODY Your Maxx includes an innovative latching system for securing the body to the chassis. To remove the body for chassis access: 1. Turn the handle 90 degrees counterclockwise to unlock the body latch. - Page 7 ANATOMY OF THE TRAXXAS MAXX Upper Suspension Arm Motor with Cooling Fan Traxxas High-Current Steering Block Caster Block (C-hub) Connector Battery Gear Cover Compartment Spur Gear Battery Hold-Down Wheelie Bar Steering Servo Rear Bumper Chassis Receiver Box Front Bumper Receiver...
-
Page 8: Quick Start: Getting Up To Speed
Make a habit of turning the transmitter on first, and off last. Follow these critical steps to maintain the performance of your model and keep it in excellent running condition. Look for the Quick Start logo at the bottom of Quick Start pages. 8 • MAXX... -
Page 9: Radio System
Cogging - Cogging is a condition sometimes associated with INTRODUCTION brushless motors. Typically it is a slight stutter noticed when Your model includes the latest Traxxas TQi 2.4GHz transmitter with Applying the Decals accelerating from a stop. It happens for a very short period as Traxxas Link™... - Page 10 When flow is constricted, energy is converted to heat and is battery terminal and ground. Using the analogy of the garden lost. Traxxas power systems are optimized to reduce electrical hose, while current is the quantity of water flow in the hose, resistance and the resulting power-robbing heat.
- Page 11 TRAXXAS TQ RADIO SYSTEM Your model is equipped with the TQi 2.4GHz transmitter with Traxxas Link ™ Model Memory. The transmitter has two channels for Wiring Diagram controlling your throttle and steering. The receiver inside the model has 5 output channels. Your model is equipped with one servo and an electronic speed control.
- Page 12 (LiPo) battery equipped with the Traxxas High Current Connector is green, check the polarity of required. Do not use a Nickle Metal Hydride (NiMH) battery. Traxxas the batteries. If you see any other flashing signal from the...
- Page 13 Traxxas iD chargers and batteries. Note: The battery compartment includes foam spacers to accommodate the Traxxas 5000mAh 4s battery packs (part #2888X). When using other Forward The Traxxas LiPo batteries, additional battery pack spacers may be required for proper High-Current Connector fitment (part #8919, sold separately).
- Page 14 (center) point of the steering channel. off (.5 seconds). Note: Traxxas Stability Management (TSM) must be completely 5. Turn the steering wheel on the transmitter back and forth and turned off while adjusting steering trim. See page 15 for TSM check for rapid operation of the steering servo.
- Page 15 Once stopped, return the the previous section. throttle trigger to neutral. Maxx®. TSM makes your model much easier to control on slippery 2. Have a friend hold the model. Make sure hands and clothing are Push the throttle trigger surfaces such as loose dirt, smooth concrete, and even ice and snow.
- Page 16 Make sure there is adequate wire at the end of the metal tip. secured by a 3x4mm set screw. space around your Maxx and no people To remove the antenna tube, or animals are nearby before self righting. simply remove the set screw...
-
Page 17: Adjusting The Electronic Speed Control
Motor/battery wiring: WARNING: FIRE HAZARD! 10-gauge Maxx® Cable (B). Do not use LiPo batteries in this vehicle with Low-Voltage 5. When the LED blinks RED TWICE, Once Red Weight: Detection disabled. - Page 18 LED light kits or additional cooling 2. Press and hold the EZ-Set button until the fans (see Traxxas.com for additional information). LED turns solid green, then solid red and Always be sure to keep the panel cover installed when...
- Page 19 (see above) occur at the same time or there is a charged battery is connected. critical functioning or programming error. Disconnect the battery and contact Traxxas Customer Service for • Voltage LED (V) Slow Blinking Red: The VXL-4s has assistance.
-
Page 20: Driving Your Model
RUNNING IN WET CONDITIONS • Use good, common sense whenever you are driving your model. Your new Traxxas model is designed with water-resistant features Intentionally driving in an abusive and rough manner will only to protect the electronics in the model (receiver, servo, electronic result in poor performance and broken parts. - Page 21 Do not conditions. submerge the motor under water. • The Traxxas TQi transmitter is not water resistant. Do not subject it • Do not gear the motor by temperature when running in wet to wet conditions such as rain.
- Page 22 5. Install the wire clamp and tighten the • Differentials: Remove, disassemble, clean, and re-grease the two 2.5x10mm cap screws securely. differential components. Use a light coating of Traxxas high- 6. Using double-sided adhesive foam tape, performance grease (part #5041) on the metal gear teeth. Refer install the receiver into the box.
-
Page 23: Basic Tuning Adjustments
100% pure silicone shock oil to help prolong the life of the the front and rear suspension seals. From the factory, the GT-Maxx shocks are filled with 30W arms). If you plan on driving shock oil. When adding shock fluid, be sure to allow any air on hard surfaces, move all four bubbles to escape. - Page 24 Incorrect gear mesh is the most common cause of stripped spur bottom of the chassis to 4x12mm BCS gears. Maxx makes improper gear mesh virtually impossible. A pin set gear mesh. Loosen system helps set the motor in the proper place according to the the two 4x12mm button- pinion and spur gear that are selected.
- Page 25 BASIC TUNING ADJUSTMENTS From the factory, both the differentials are filled with SAE 50,000W viscosity silicone oil. Only use silicone oil in the differentials. Traxxas sells Your Battery Selection and Pinion/Spur Selection Determines Your Speed. SAE 10,000W, SAE 30,000W, SAE 100,000W, and SAE 500,000W viscosity How Fast Do You Want To Go? oil (see your parts list).
-
Page 26: Maintaining Your Model
If the bottom of the shock is leaking, then it is time 4. Check the wiring for any frayed wires or loose connections. for a rebuild. The Traxxas rebuild kit for two shocks is part #8962. 5. Check the mounting of the receiver and servo(s) and •... - Page 27 6. Remove the two 4x22mm button-head cap screws that secure the rear bulkhead to the top of the chassis. 7. Pull the rear suspension assembly away from the chassis. Pull the assembly away firmly. To reassemble the modules, follow the steps in reverse order. 4x12mm MAXX • 27 4x20mm CCS...
-
Page 28: Tq I Advanced Tuning Guide
The Multi-Function knob can be set to control Throttle Sensitivity. Restoring Factory Defaults Traxxas Stability Management (TSM) by default, see page 15). Accessing Throttle Sensitivity works the same way as Steering Sensitivity, but the programming menu is done by using the menu and set buttons on applies the effect to the throttle channel. - Page 29 ™ This allows you to fine-tune the servo settings to prevent binding vehicles with a single transmitter via Traxxas Link Model Memory. function that returns the throttle caused by the servo moving steering or throttle linkages (in the case...
- Page 30 Model Lock locked. Press and hold MENU to return to driving mode. The Traxxas Link Model Memory feature can store up to thirty models Note: To unlock a memory, press SET twice at step 5. The LED will (receivers) in its memory. If you bind a thirty-first receiver, Traxxas Link blink rapidly green to indicate the model is unlocked.
- Page 31 Transmitter is restored to default Press C onfirm Deletion Delete Model Two Blinks Green One Blink Red *Torque Control is a feature designed only for use with the power system in the Traxxas Funny Car Race Replica (Model #6907).
- Page 32 ADVANCED TUNING GUIDE Set Multi-Function MENU TREE FORMULAS knob for STEERING Press/hold MENU Press SET Press SET to confirm Press/hold MENU SENSITIVITY (Expo) To select functions and make adjustments to the TQi transmitter without green LED blinks red LED blinks green LED blinks (x8) returns to driving mode referencing the menu tree, turn your transmitter on, find the function in the...
- Page 33 Real-Time Telemetry Traxxas Link For more information about the Traxxas Link The powerful Traxxas Link app (available in the Apple App Store or on When you equip your model Wireless Module and the Google Play™) gives you complete control over the operation and tuning...
- Page 34 OWNER’S MANUAL MODEL 89076-4 6250 Traxxas Way, McKinney, TX 75070 1-888-TRAXXAS 200424 89076-4-OM-EN-R01...
Need help?
Do you have a question about the Maxx and is the answer not in the manual?
Questions and answers