Displaying The Smartphone Link Adaptor Firmware Version; Updating Firmware; Displaying The Firmware Version; Setting Mixtrax Mode - Pioneer AVH-X4690DVD Owner's Manual

Section
18 System settings
Important
! The USB storage device for updating must
contain only the correct update file. If the
USB storage device contains multiple files,
the update will fail.
! Never turn the unit off and never disconnect
the USB storage device while the firmware is
being updated.
! You can only start the firmware update when
the vehicle is stopped and the parking brake
is engaged.
1 Downloading the firmware update files.
2 Connect a blank (formatted) USB storage
device to your computer, and then locate
and copy the correct update file onto the
USB storage device.
3 Turn the source off.
Refer to Turning the source ON/OFF on page 6.
4 Press the home button to switch to the
home display.
5 Touch the system key to open the system
menu.
6 Touch CD-ML100 Update on the system
menu.
7 Connect the USB storage device to the
smartphone link adaptor.
Refer to Connection for updating Smartphone
link adaptor firmware on page 47.
8 Touch Continue to display the update
mode.
Follow the on-screen instructions to finish up-
dating the smartphone link adaptor.
9 Remove the USB storage device from the
smartphone link adaptor.
34
En
10 Turn the ignition switch OFF and then to
ACC or ON.
Notes
! If update failed, please consult your dealer or
the nearest authorized PIONEER Service Sta-
tion.
! You cannot update while connected to
Bluetooth.
Displaying the smartphone
link adaptor firmware version
If smartphone link adaptor fails to operate prop-
erly, you may need to consult your dealer for re-
pair. In such cases, you may be asked to specify
the firmware version. Perform the following pro-
cedure to check the version on smartphone link
adaptor.
1 Turn the source off.
Refer to Turning the source ON/OFF on page 6.
2 Press the home button to switch to the
home display.
3 Touch the system key to open the system
menu.
4 Touch CD-ML100 Firmware Info to display
to the version of the firmware of smart-
phone link adaptor.

Updating firmware

This function is used to update this unit with the
latest firmware.
For about firmware and updating, refer to our
website.
System settings
Important
! The USB storage device for updating must
contain only the correct update file. If the
USB storage device contains multiple files,
the update will fail.
! Never turn the unit off and never disconnect
the USB storage device while the firmware is
being updated.
! You can only start the firmware update when
the vehicle is stopped and the parking brake
is engaged.
1 Downloading the firmware update files.
2 Connect a blank (formatted) USB storage
device to your computer, and then locate
and copy the correct update file onto the
USB storage device.
3 Turn the source off.
Refer to Turning the source ON/OFF on page 6.
4 Press the home button to switch to the
home display.
5 Touch the system key to open the system
menu.
You can check the current version of your unit's
firmware. Touch Firmware Information on the
system menu to open the
Firmware Information screen.
6 Touch Firmware Update on the system
menu.
The confirmation screen appears on the display.
7 Connect the USB storage device accord-
ing to the on-screen messages.
8 Touch Continue to display the read file
mode.
Check any messages if warning screens appear
on the display.
9 Touch Start to display the data transfer
mode.
# Follow the on-screen instructions to finish updat-
ing the firmware.
# This unit will reset automatically after the firm-
ware update is completed if the update is success-
ful.
Note
If "Update Failed!" appears on the screen, turn
the ignition switch to OFF, then turn the ignition
switch to the ACC position to proceed and start
the recovery sequence.
Displaying the firmware
version
If this unit fails to operate properly, you may
need to consult your dealer for repair. In such
cases, you may be asked to specify the firmware
version. Perform the following procedure to
check the version on this unit.
1 Turn the source off.
Refer to Turning the source ON/OFF on page 6.
2 Press the home button to switch to the
home display.
3 Touch the system key to open the system
menu.
4 Touch Firmware Information to display to
the version of the firmware of this unit.

Setting MIXTRAX mode

Refer to Setting MIXTRAX mode on page 24.