Table of Contents
Advertisement
3.0 Safety warnings
1. Read and understand entire owner's manual
before attempting assembly or operation.
2. Read and understand the warnings posted on
the machine and in this manual. Failure to
comply with all of these warnings may cause
serious injury.
3. Replace warning labels if they become
obscured or removed.
4. This lathe is designed and intended for use by
properly trained and experienced personnel
only. If you are not familiar with the proper and
safe operation of a lathe, do not use until
proper training and knowledge have been
obtained.
5. Do not use this lathe for other than its intended
use. If used for other purposes, Walter Meier
(Manufacturing) Inc., disclaims any real or
implied warranty and holds itself harmless from
any injury that may result from that use.
6. Always wear approved safety glasses or face
shields while using this lathe. Everyday
eyeglasses only have impact resistant lenses;
they are not safety glasses.
7. Before operating this lathe, remove tie, rings,
watches and other jewelry, and roll sleeves up
past the elbows. Remove all loose clothing
and confine long hair. Non-slip footwear or
anti-skid floor strips are recommended. Do not
wear gloves.
8. Wear ear protectors (plugs or muffs) during
extended periods of operation.
9. Some dust created by power sanding, sawing,
grinding,
drilling
activities contain chemicals known to cause
cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
•
Lead from lead based paint.
•
Crystalline silica from bricks, cement and
other masonry products.
•
Arsenic and chromium from chemically
treated lumber.
Your risk of exposure varies, depending on
how often you do this type of work. To reduce
your exposure to these chemicals, work in a
well-ventilated area and work with approved
safety equipment, such as face or dust masks
that are specifically designed to filter out
microscopic particles.
and
other
construction
10. Do not operate this machine while tired or
under the influence of drugs, alcohol or any
medication which may impair your judgment.
11. Make certain switch is in OFF position before
connecting machine to power supply.
12. Make certain machine is properly grounded.
13. Make all machine adjustments or maintenance
with machine unplugged from power source.
14. Remove adjusting keys and wrenches. Form a
habit of checking to see that keys and
adjusting wrenches are removed from the
machine before turning it on.
15. Keep safety guards in place at all times when
machine is in use. If removed for maintenance
purposes, use extreme caution and replace
the guards immediately after completion of
maintenance.
16. Check damaged parts. Before further use of
the machine, a guard or other part that is
damaged should be carefully checked to
determine that it will operate properly and
perform its intended function. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, mounting and any
other conditions that may affect its operation.
A guard or other part that is damaged should
be properly repaired or replaced.
17. Provide for adequate space surrounding work
area and non-glare, overhead lighting.
18. Keep floor around machine clean and free of
scrap material, oil and grease.
19. Keep visitors a safe distance from the work
area. Keep children away.
20. Make your workshop child proof with padlocks,
master switches or by removing starter keys.
21. Give your work undivided attention. Looking
around, carrying on a conversation and "horse-
play" are careless acts that can result in
serious injury.
22. Maintain a balanced stance at all times so that
you do not fall against the spindle, workpiece
or other moving parts. Do not overreach or use
excessive force to perform any machine
operation.
23. Use the right tool at the correct speed and
feed rate. Do not force a tool or attachment to
do a job for which it was not designed. The
right tool will do the job better and more safely.
24. Use
recommended
accessories may be hazardous.
25. Keep turning tools sharp and clean for the best
and safest performance, and position tools
properly in relation to the workpiece.
5
accessories; improper
Advertisement
Table of Contents
