Table of Contents
Advertisement
3.0 Safety warnings
1.
Read and understand the entire owner's
manual
before
attempting
operation.
2.
Read and understand the warnings posted on
the machine and in this manual. Failure to
comply with all of these warnings may cause
serious injury.
3.
Replace the warning labels if they become
obscured or removed.
4.
This Lathe is designed and intended for use by
properly trained and experienced personnel
only. If you are not familiar with the proper and
safe operation of a Lathe, do not use until
proper training and knowledge have been
obtained.
5.
Do not use this Lathe for other than its
intended use. If used for other purposes,
Powermatic disclaims any real or implied
warranty and holds itself harmless from any
injury that may result from that use.
6.
Always wear approved safety glasses/face
shields while using this machine. Everyday
eyeglasses only have impact resistant lenses;
they are not safety glasses.
7.
Before operating this Lathe, remove tie, rings,
watches and other jewelry, and roll sleeves up
past the elbows. Remove all loose clothing
and confine long hair. Non-slip footwear or
anti-skid floor strips are recommended. Do not
wear gloves.
8.
Wear ear protectors (plugs or muffs) during
extended periods of operation.
9.
Do not operate this machine while tired or
under the influence of drugs, alcohol or any
medication.
10. Do not expose this machine to rain, or operate
machine in damp locations.
11. Make certain the switch is in the OFF position
before connecting the machine to the power
supply.
12. Make
certain
the
grounded.
13. Make all machine adjustments or maintenance
with the machine unplugged from the power
source.
14. Remove adjusting keys and wrenches. Form a
habit of checking to see that keys and
adjusting wrenches are removed from the
machine before turning it on.
assembly
or
machine
is
properly
15. Keep the safety guard in place at all times
when the machine is in use. If removed for
maintenance
purposes
procedures which do not permit its use,
exercise extreme caution and replace the
guard immediately after the operation is
complete.
16. Check damaged parts. Before further use of
the machine, a guard or other part that is
damaged should be carefully checked to
determine that it will operate properly and
perform its intended function. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, mounting and any
other conditions that may affect its operation.
A guard or other part that is damaged should
be properly repaired or replaced.
17. Provide for adequate space surrounding work
area and non-glare, overhead lighting.
18. Keep the floor around the machine clean and
free of scrap material, oil and grease.
19. Keep visitors a safe distance from the work
area. Keep children away.
20. Make your workshop child proof with padlocks,
master switches or by removing starter keys.
21. Give your work undivided attention. Looking
around, carrying on a conversation and "horse-
play" are careless acts that can result in
serious injury.
22. Maintain a balanced stance at all times so that
you do not fall or lean against the centers,
workpiece or other moving parts. Do not
overreach or use excessive force to perform
any machine operation.
23. Use the right tool at the correct speed and
feed rate. Do not force a tool or attachment to
do a job for which it was not designed. The
right tool will do the job better and safer.
24. Use
recommended
accessories may be hazardous.
25. Keep turning tools sharp and clean for the best
and safest performance, and position the tools
properly in relation to the workpiece.
26. Turn off the machine before cleaning. Use a
brush or compressed air to remove chips or
debris — do not use your hands.
27. Do not stand on the machine. Serious injury
could occur if the machine tips over.
28. Never leave the Lathe running unattended.
Turn the power off and do not leave the
machine until it comes to a complete stop.
29. Remove loose items and unnecessary work
pieces from the area before starting the
machine.
or
for
turning
accessories;
improper
Advertisement
Table of Contents
