ALLEN & HEATH MixWizard WZ3 20S User Manual page 28

MONO CH - AUX PRE/POST EQ
L K J I H
PO SW PO SW PR SW
AUX 6 5 3-4
MONO CH - DIRECT OUT
L K J I H
PO SW PO SW PR SW
AUX 6 5 3-4
MONO CH - AUX PRE/POST FADER
PR=PRE
L K J I H
PO=POST
SW=SWITCH
PO SW PO SW PR SW
AUX 6 5 3-4
STEREO CH - AUX PRE/POST FADER
PR=PRE L K J I H
PO=POST
PO SW PO SW PR SW
SW=SWITCH
6 5 4
STEREO CH - MONO/STEREO AUXES
CN5
MONO STEREO
CN4
MONO STEREO
AUX MASTER - EXT1 MONO/STEREO
JP1
MONO STEREO
LR MASTER - AB SOURCE
R L R
PRE POST
28
G F E D C B A
PR SW PO PR PO PR
1-2 DIR AUX
PRE-INSERT/POST-EQ
G F E D C B A
PR SW PO PR PO PR
1-2 DIR AUX
G F E D C B A
PR SW PO PR PO PR
1-2 DIR AUX
G F E D C B A
PR SW PR SW PR SW
3 2 1 AUX
POST-FADE AUXES
PRE-FADE AUXES
EXT1 AUX SOURCE
AB PRE/POST LR FADER
L
Aux pre/post insert/EQ
the mono channel pre-fade auxes is pre-insert, pre-
EQ. This is popular with many users mixing monitors
from FOH. It prevents the channel EQ and inserted
compressors affecting the monitor mix.
jumper from A to B to change this to post-insert,
post-EQ if preferred. Note that auxes are always
post-mute.
Direct output source
fader. This is common for live recording to
multitrack. The live mix fader movements do not
affect the recording. Move the jumper from C to D to
change to post-fade. Post-fade is appropriate when
using the output as a direct channel effects send.
Channel Aux pre/post settings
default is Aux 1-4 = switched, Aux 5-6 = switched
You can change these settings for
combinations of pre/post or switched auxes by
repositioning the links. Refer to the system block
diagram to explore the possibilities. Make sure you
set all mono and stereo channels the same.
recommend you only change these settings if
absolutely necessary.
Stereo/Mono aux source
channels can feed the auxes with a mono sum of
L+R, or be configured so that L feeds the odd
numbered auxes, and R the even. This is preferred
when using odd/even auxes as stereo pairs. Factory
default is the mono setting. Note that you should
also set the EXT1 stereo/mono jumper to the same
position.
EXT1 stereo/mono aux source
channel EXT1 feeds Auxes 1-4 with a mono sum of
the stereo signal. If you are working with stereo
auxes you can reconfigure this for stereo with L
feeding Auxes 1, 3 and R feeding Auxes 2, 4. The
jumper is found behind the AUX2 send control.
AB source pre or post LR faders
factory default is that the post-fade LR mix feeds the
AB output. If you prefer the master LR faders not to
affect the AB output then reposition the two option
jumpers in the PRE position. This may be desired if
you are using the AB output to feed a 2-track
recording independent of the house level.
Factory default for
Move the
Factory default is pre-
Factory
different
We
The stereo
The return
The
3
WZ 20S
User Guide