Advertisement
PREPARATION
REMOTE CONTROLLER HOLDER
To set the remote controller in
1
the holder
1. Insert.
2
2. Press in.
1
To take out the remote con-
troller from the holder
1. Slide up.
2. Pull out.
2
SET THE CURRENT TIME
1. Press the TIME ADJUST
button.
2. Press the
2
3. Press the TIME ADJUST
button.
1, 3
NOTES
(1) The remote controller must be pointed at signal receiver to operate correctly.
(2) Operating range : About 7 meters.
(3) Beeping sound
• When a signal is properly received by the air conditioner, a beeping sound will
be heard twice.
• If an invalid signal is received by the air conditioner, a beeping sound will be
heard 5 times.
• If no beeping sound is heard, press the remote controller button again.
(4) The buttons except the SLEEP, TIME ADJUST and ACL buttons can only be se-
lected while in operation mode.
(5) PROGRAM timer
• The PROGRAM timer allows you to integrate OFF timer and ON timer opera-
tions in a single sequence.
• The first timer function to operate will be the one set nearest to the current time.
(6) SLEEP timer
To prevent excessive warming or cooling during sleep, the SLEEP timer function
automatically modifies the set temperature in accordance with the time setting.
When the set time has elapsed, the air conditioner completely stops.
(7) When connecting with other controllers, the indoor unit might be controlled by the
other controllers.
(8) The wired remote controller or the simple remote controller can also be used with
this unit.
SLEEP TIMER
To set or change the SLEEP Timer
1. Press the
2. Press the
Adjust the OFF TIME.
To cancel the SLEEP Timer
Press the
Select
(TIMER RESET).
The air conditioner will return to normal operation.
MASTER CONTROL
Press the
NOTES
*
AUTO
(Select operation
mode automatically.)
*
"AUTO" and "FAN" cannot be selected in AIRSTAGE™
/
button.
(VRF system) Heat Pump model.
"HEAT" cannot be selected in Cooling Only model.
TEMPERATURE
Press the
/
NOTES
Temperature setting range
AUTO • • • • • • • • • • • • • • 18 to 30 °C
HEAT • • • • • • • • • • • • • • • 16 to 30 °C
COOL/DRY • • • • • • • • • • 18 to 30 °C
The thermostat setting should be considered a standard
value, and may differ somewhat from the actual room tem-
perature.
AIR DIRECTION (UPPER AND LOWER)
Press the
For swing operation:
Press the
Stop the setting by pressing it again.
NOTES
Refer to the operating manual of the indoor unit for range
of swing.
(SLEEP) button.
/
button.
button.
button while in operation.
*
*
COOL
DRY
FAN
HEAT
button while in operation.
button while in operation.
START / STOP
button while in operation.
Each press of the
button alternates opera-
tion and stop.
OPERATION
ON / OFF TIMER
1. Press the
Select
(OFF TIMER) or
NOTES
RESET
2. Press the
Adjust the OFF or ON TIME.
PROGRAM TIMER
To set or change the PROGRAM Timer
1. Press the
Select
(OFF TIMER).
2. Press the
Adjust the OFF time.
3. Repeat Step 1 and 2 to adjust ON time.
4. Press the
Select
(If the ON timer has been selected to operate
first, the unit will stop operating at this point.)
To cancel the PROGRAM Timer
Press the
button.
Select
(TIMER RESET).
The air conditioner will return to normal operation.
FAN SPEED
Press the
button while in operation.
NOTES
AUTO
(Select the fan speed
automatically.)
AIR DIRECTION (RIGHT AND LEFT)
Press the
button while in operation.
For swing operation:
Press the
button while in operation.
Stop the setting by pressing it again.
NOTES
Refer to the operating manual of the indoor unit for range of
swing.
button.
(ON TIMER).
OFF TIMER
ON TIMER
PROGRAM TIMER (OFF←ON, OFF→ON)
/
button.
button.
/
button.
button.
(PROGRAM TIMER).
HIGH
LOW
MED
Advertisement
