B. To Operate The Vehicle While Running On The Remote Start - Autopage C3-RS-1000 OLED Operation Manual

Professional oled 2-way 915 mhz. fm remote car starter & 6 channel alarm system with built-in temperature sensor and two-way serial port data link
Table of Contents

Advertisement

SVMASTER -
A. TO REMOTE START THE VEHICLE:
1. Press the
2. The parking light will activate to indicate the remote start received the signal. ( A
melody sound from your Remote OLED transceiver and "
OLED screen to confirm the remote start was activated.)
3. The engine will start in approximately 5 seconds.
4. Once the engine is running, after the parking lights will turn on again and your
climate controls will activate and adjust the vehicles interior temperature to your
Preset setting. (While the vehicle is running, the " E ngine Running" icon and the
"minutes" digit on the OLED screen will flash. It will indicate a count down timer
based on the 5, 10, 20 or 30 minute run time set up by your installation center.)
5. The vehicle will run for a 5 to 30 minute cycle and automatically shut down. (When
the unit shuts off the count down timer will turn off and the transmitter wil l play a
melody.)
Note: The Remote Start Unit will not start the vehicle if any one of the following
conditions exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. Move the optional remote start enable toggle switch to OFF position. (If installed)
4. The gear selector is in any gear other then "PARK" or "NEUTRAL"

B. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START:

To operate the vehicle while engine running on the remote start.
1. Enter the vehicle and insert the ignition key. Turn it to "ON" not the start position.
2. Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down.
C. TEMPORARY STOP FEATURE:
This feature allows the vehicle to remain running after the key has been removed from the ignition. This
feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would
like to leave the motor running and the climate control on.
1. Before turning off the engine, press the
programmed. The LED indicator will flash 3 times to confirm.
2.Turn the ignition key to OFF position. (The engine will stay running.)
3.The engine will run until the pre-programmed time elapsed or a shutdown input is received.
D. TURBO TIMER MODE:
Turbo timer mode keeps the engine running after arriving at your destination for a
programmable period of 1, 3 or 5 minutes. This allows the system time to conveniently
cool down the turbo after you have left the vehicle. To activate the turbo timer:
1. While engine is running, place the transmission gear in the park position and pull up
the hand brake.
2. Before turning off the engine, Spin up the
"Turbo Start" button or press and release
-- The parking light will activate to indicate the remote start has entered turbo timer mode. --
3. Pull out the "Ignition Key" from the key cylinder.
-- The engine will continue to run. --
4. Exit and secure the vehicle.
-- Engine continues running until the pre-programmed time has elapsed. --
If you do not want the vehicle to continue running, simply step on the vehicle's brake, or activate the
button in succession. Any of these will cause the engine to turn off.
E. TIMER START:
Your system has the ability to automatically start the vehicle every 1,2 or 3 hours and run for the
pre-programmed time (5, 10, 20 or 30 minutes), and then shut off. This will continue for 6 cycles. This feature
is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to
periodically start the engine.
If the system is set up to start in temperature mode, the system can be programmed to automatically start
the vehicle's engine whenever the temperature inside the vehicle reaches or drops below the preprogrammed
temperature level. The system will monitor the air temperature every 3 hours and will only start the engine
SVMASTER -
C3RS1000 OP 3/08
REMOTE START OPERATION:
button on the transmitter. Twice if safety start has been programmed.
" icon will flash on the
button on the transmitter. Twice if safety start has been
switch to the page
and then press the
5
and
buttons at the same time.
20
http://www.msvmaster.lv
-
http://www.msvmaster.lv
-

Advertisement

Table of Contents
loading

Table of Contents