Initial Settings - Pioneer DEH-4400BT Operation Manual

Section
02 Operating this unit

Initial settings

Important
PW SAVE (power saving) is cancelled if the vehi-
cle battery is disconnected and will need to be
turned back on once the battery is reconnected.
When PW SAVE (power saving) is off, depending
on connection methods, the unit may continue to
draw power from the battery if your vehicle's igni-
tion doesn't have an ACC (accessory) position.
1 Press and hold SRC/OFF until the unit
turns off.
2 Press SRC/OFF and hold until function
name appears in the display.
3 Turn M.C. to select the initial setting.
After selecting, perform the following proce-
dures to set the initial setting.
CLOCK SET (setting the clock)
1 Press M.C. to display the setting mode.
2 Press M.C. to select the segment of the clock dis-
play you wish to set.
Hour—Minute
3 Turn M.C. to adjust the clock.
CLOCK (clock display)
You can turn the clock display on or off.
The clock display disappears temporarily when you
perform other operations, but the clock display ap-
pears again after 25 seconds.
1 Press M.C. to turn the clock display on or off.
FM STEP (FM tuning step)
Normally, the FM tuning step employed by seek tun-
ing is 50 kHz. When AF or TA is on, the tuning step
automatically changes to 100 kHz. It may be prefer-
able to set the tuning step to 50 kHz when AF is on.
! The tuning step remains at 50 kHz during manual
tuning.
1 Press M.C. to select the FM tuning step.
50 (50 kHz)—100 (100 kHz)
AUTO-PI (auto PI seek)
The unit can automatically search for a different sta-
tion with the same programming, even during preset
recall.
1 Press M.C. to turn Auto PI seek on or off.
AUX (auxiliary input)
18
En
Activate this setting when using an auxiliary device
connected to this unit.
1 Press M.C. to turn AUX on or off.
USB PNP (plug and play)
This setting allows you to switch your source to USB/
iPod automatically.
1 Press M.C. to turn the plug and play function on
or off.
ON – When a USB storage device/iPod is con-
nected, depending on the type of device, the
source is automatically switched to USB/iPod
when you turn on the engine. If you disconnect
your USB storage device/iPod, this unit's source
is turned off.
OFF – When a USB storage device/iPod is con-
nected, the source is not switched to USB/iPod
automatically. Please change the source to USB/
iPod manually.
REAR-SP (rear output setting)
The rear speaker leads output can be used for full-
range speaker or subwoofer connection.
If you switch to SW, you can connect a rear speaker
lead directly to a subwoofer without using an auxiliary
amp.
Initially, REAR-SP is set for rear full-range speaker
connection (FUL).
1 Press M.C. to select the desired setting.
FUL—SW
! Even if you change this setting, there will be
! If you change this setting, subwoofer output
PREOUT (preout setting)
The RCA outputs can be used for rear speaker or sub-
woofer connection.
If you switch to SW, you can connect a rear speaker
lead directly to a subwoofer without using an auxiliary
amp.
Initially, PREOUT is set for rear full-range speaker con-
nection (SW).
1 Press M.C. to select the desired setting.
SW—REA
! Even if you change this setting, there will be
! If you change this setting, subwoofer output
DEMO (demo display setting)
Autogood products «130»
no output if you select OFF in SUB.W (Refer to
SUB.W (subwoofer on/off setting) on the pre-
vious page).
in the audio menu will return to the factory
settings.
no output if you select OFF in SUB.W (Refer to
SUB.W (subwoofer on/off setting) on the pre-
vious page).
in the audio menu will return to the factory
settings.