Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ProVisual PTZ-9610-A
Summary of Contents for ProVisual PTZ-9610-A
- Page 1 Indoor Mini High Speed PTZ Dome Camera PTZ-9610-A User Manual...
-
Page 2: Table Of Contents
Contents Features ........................3 1.1 Features ..................... 3 1.2 Specifications ................... 5 Installation ......................6 2.1 Installation and Connection ..............6 2.1.2. Ceiling Mount ..................6 2.1.3 Cabling....................6 2.2.1 Camera ID Setup ................... 6 2.2.2 Communication Protocol and Baud rate Setup ........7 Operation ........................ -
Page 3: Features
Features 1.1 Features Camera Specifications: CCD Sensor: 1/3” Sony Effio CCD Color 960H. Zoom Magnification: 10X Optical zoom. Day & Night function: The camera is configured to switch to the black and white mode automatically under low light conditions and at night for clear images. Various focus mode: Auto Focus / Manual Focus / Semi-Auto Focus. - Page 4 for a long time. Reserved Presets for special purpose: besides regular 256 presets, direct calling of ● reserved presets enable to set up many of camera functions with / without using OSD menu. PTZ (Pan /Tilt /Zoom) Control: RS485 Communication. ●...
-
Page 5: Specifications
1.2 Specifications Video Signal System NTSC 1/3” Sony Effio CCD Color 960H Max. Pixels 976 (H) X 494 (V) Horizontal Res 700TV Lines S/N Ratio 50dB (AGC off) Zoom X10 Optical Zoom Focal Length F1.8, f=3.8~38mm Camera Min. illumination 0.7Lux (Color),0.02Lux (B/W), F1.8, 50 IRE Day &... -
Page 6: Installation
Installation 2.1 Installation and Connection (1) Connect Camera Plug the terminals into the bottom of the main unit, then, fix the main unit with screws supplied. 2.1.2. Ceiling Mount （1）Fix the main unit to the ceiling using screws provided. After wiring cables to terminals, plug the terminals into the bottom of main unit. Then, fix the main unit with screws provided. -
Page 7: Communication Protocol And Baud Rate Setup
16, 32, 64 and 128. For example, switch 1, 3, 5, 7 to “ON” position, the corresponding ID should be 1+4+16+64=85. The example is shown bellow. ID No Code Switch ID No Code Switch 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0... -
Page 8: Operation
Select the appropriate protocol with DIP switch combination. Switch State Protocol Pin No Pin 1 Pin 2 Pin 3 Pin 4 PELCO-P PELCO-D Protocol Auto Reserved 9600 2400 Baud rate 4800 9600 Operation 3.1 Check points before operation Before power is connected, please check the cables carefully. ... -
Page 9: Reserved Preset
in advance to operate camera function using them.(Refer to your System keyboard Manual) ● If controller or DVR has no pattern button or function, use shortcut keys with preset numbers. For more information, refer to “Reserved Preset” in this manual. ●... -
Page 10: Iris
Press “Focus Near” key to shorten the distance of near scene. 3.3.3 Iris Press “Iris Open” key to adjust the brightness. How to Use OSD Menu After power up or restart, the present Protocol, Baud rate and Address will be displayed on the screen as below: PTOL：... -
Page 11: System Information
<SYSTEM INFORMATION>：Shows system information. <ADDR SETTING>：Select and setup Soft/Hard address. <MOTION>：Setup for motion related settings. <PATTERNS>：Setup for Patterns. <CAMERA>：Configure Camera related functions and data. <CRUISE SETTING>：Setup presets scan. <DISPLAY SETUP>：Enable / Disable of OSD display on main screen. <RESTORE FACTORY DEFAULT>：Restore factory settings. <REBOOT SYSTEM>：Reboot the system. -
Page 12: Address Setting
4.2.2 Address Setting ADDR SETTING ADDR TYPE HARD ADDR SOFT ADDR HARD BACK EXIT ADDR TYPE：Choose the address type (Hard/Soft Add), when you choose soft type, the user can setup the address by remote access. ADDR SOFT：Setup soft address. Press UP/DOWN” keys of your controller and setup the camera ID from 0~254. - Page 13 FRAME SCAN SPEED: Set the speed between two presets from1~32. RANDOM SCAN SPEED: Set the speed of 360° continuous and intermittent scan. Set Frame Scan FRAME SCAN SET SCAN POSITION CLEAR FRAME SCAN BACK EXIT SET SCAN POSITION：Set up scan range between two positions (Left/Right extreme position).
-
Page 14: Patterns
4.2.4 Patterns PATTERNS PATTERN NUMBER PROGRAM PATTERN CLEAR CURRENT PATTERN CLEAR ALL PATTERN BACK EXIT 4 Patterns are supported, please refer to below details: <PATTERN NUMBER> Set Pattern number (1~4). <PROGRAM PATTERN>: Pattern scan program. <CLEAR CURRENT PATTERN> Deletes data in current pattern. 1．Pattern Number （1）Move the cursor to “PATTERN NUMBER”... -
Page 15: Camera Setup
4.2.5 Camera setup We are using Samsung SDM-100P camera to explain below operation. Main Menu Camera label White Balance Auto Auto Detection Focus Exposure Additional Menu Back Exit Notice：“Up/Down” keys for option, “Left/Right” keys for details, “Iris Open” for sub-menu. 1. - Page 16 2.2 Manual: Close auto WB, adjust Red and Blue level manually. Manual WB 30…|...………. Blue 41…..…|……. Exit Red adjust range: 0~100 Blue adjust range: 0~100 2.3 Auto BW: This mode is the most accurate and reliable for most places. 3. Backlight Compensation setup Backlight High/Middle/Low/Off 4.
- Page 17 5. Focus Setup Focus Mode Auto Zoom trace mode Zoom trace speed Fast Digital Zoom Show Zoom Initial Zoom Position Lens Initialization Exit 1 Mode：Auto, Manual, One-off Auto focus. Press “Iris Open” to enter sub-menu. One-off auto focus: Once the image zoom changes, the camera will automatically focus and fix the status till the image change again.
- Page 18 (2) One-off Auto focus and Manual focus Adjustment: Setup Zoom Zoom In Zoom Out Near Back: Press “SET” key 2. Zoom trace mode: Manual Focus: Off. Auto and One-off Auto Focus: On / Off. 3. Zoom trace speed: Fast/Slow. 4. Digital zoom: On / Off, range: X2~X10. Digital Zoom Digital Zoom Exit...
- Page 19 Brightness range: 0~100. Iris：Auto/ Manual. Press “Iris Open” to enter into manual setup Manual Iris Iris 100….………| Exit If the number of iris is set to higher, the image will be brighter. Shutter mode: Flicker / Manual / Auto The shutter speed of Anti-flash is 1/100（NTSC） ，1/120（PAL） Manual mode setting (PAL）:2X、4X、6X、8X、10X、12X、14X、16X、24X、...
- Page 20 9 Additional menu: Additional menu User setup Privacy zone mask Day & Night Auto 1 Sync. system Internal Image adjustment Exit (1) User preset setup: On / Off User Preset User preset number No 1 User preset mode Save Clear Exit preset not setup.
- Page 21 Focus: Using direction keys to “Focus” and press “Iris/Open” key to set up. Focus Mode Auto Zoom trace mode Zoom trace speed Fast Digital zoom Show zoom Exit Other：Refer to below details. Other Camera Type Auto trace BW Motion Detection Privacy mask Day &...
- Page 22 Color: Color, range of privacy zone is 0~100. Top: Ordinate position on the top of zone. Bottom: Ordinate position on the bottom. Left: Horizontal abscissa position on the left side. Right: Horizontal abscissa position on the left side. (3) Day / Night: Day and Night function. Auto 1/ Auto 2 / Outer/ Color/ B&W mode. B&W mode: Suit for night work.
-
Page 23: Cruise Setting
4.2.6 Cruise Setting CRUISE DWELL TIME<SECS> PRESET LIST 1 ON 0 OFF 1234567890 PRESET 1101111111 [1-10] BACK EXIT Auto cruise: set up preset scan route. <Dwell Time (Sec)>: preset cruise dwell time, range:1～250 Sec. <Preset List>: (3 pages) 30 presets. <1234567890>：preset position in the preset list. -
Page 24: Trouble Shooting
Trouble Shooting Troubles Reason Solution Connect wrong cable. Correct the connection No action, no image after Power supply damaged. Change power on Bad connection. Eliminate the bad connection Maybe user setup wrong Reset IP, Protocol and Baud rate. Out of control Protocol and Baud rate. -
Page 25: Safety Information
Safety Information 1. Transportation Do not force, shake and marinate during transportation, storage and installation. 2. Installation Please handle with care, do not press the camera and its’ parts when you install, do not connect before you install the cover. 3.
Need help?
Do you have a question about the PTZ-9610-A and is the answer not in the manual?
Questions and answers