PRESONUS StudioLive 16.0.2 Owner's Manual page 86

1 Overview
Map of Controls
Trim Controls adjust the
Input Gain Level of each
channel's analog input.
It is very important
to properly adjust
these controls in order
to minimize noise and
avoid overload distortion
Follow the Quick Start
level-setting instructions
on page 1 before
operating a channel.
Encoder Mode buttons
to the left of the Fat
Channel are used to
create and view Aux
mixes. Each one of these
buttons allows you to
view and set the send
level for each channel
to that Aux or FX mix.
The GEQ Button lets you
make changes to the 31-
band Graphic EQ
MultiMode section.
Each channel and Aux
on the StudioLive 16.0.2
features a MultiMode
button. These buttons
allow you to solo or mute
a channel or Aux as well
as engage the channel
FireWire returns from
the same button! The
function of these buttons
is determined by the
control buttons directly
to the left of the row of
the MultiMode buttons
There is a Select button
on each of the 12
Meters section lets you
channels, each of the
select Input, Output,
4 analog Aux sends,
Gain Reduction, or locate
both of the internal
the fader settings so you
effects buses, and
can "zero them out".
the Main output bus.
Each of these buttons
serves exactly the same
purpose: to access the
Fat Channel parameters
for its channel or bus.
English
Español
Deutsch
Français
6 6
PreSonus StudioLive ™ 16.0.2
"Scribble Strips." Aux Output Faders
The white area above control the overall level
the fader can be used of each of the four Aux
as a scribble strip for Outputs for performers'
labeling the channel monitor mixes using
(for example, Vocal 1 or headphones, in-ear
Kick Drum). Use only oil monitors, or floor
pencils; other types of wedges.
pens or pencils cannot
be wiped off.
Channel Faders control
the overall Level of each
separate channel. The
60 mm fader has a "U"
to denote Unity Gain.
Quick Start Guide
Digital Effects / Master
Control section accesses
StudioLive's two internal
effects processors.
It is also used to store
and recall Scenes (global
snapshots of mixer
settings) and individual
The Fat Channel
Channel Presets and to
High-Pass filter is
access graphic equalizers
available on the 16
and other features.
channels of the input
FX (Effects) A and B bus, the 4 Auxes, and
Sections assign effects both internal FX buses.
to Auxes and Mains and Encoder 1 adjusts its
route the Effects buses Frequency point from
through the Fat Channel. 24 kHz to 1 kHz.
Talkback Section The Fat Channel Gate
assigns the Talkback mic is available for all input
input to Aux 1-2 or Aux and output buses. You
3-4. can set the Threshold
from 0 to -56 dB with
Solo Section includes
Encoder 2.
AFL, PFL, and Solo In
Place options.
Monitor Bus lets you
monitor multiple sources
from the Monitor
Outputs or Headphones,
including the Main
and Solo buses, main
FireWire return from your
computer, and the stereo
analog Tape input.
Main Fader controls the
overall level of the Main
stereo output.
When the Dig Out
button is enabled,
Pan control for each
the signal sent to the
input or output bus
FireWire bus is post-
is set on the Fat
EQ and post-dynamics
Channel. The LED
processing; When the
display shows the pan
button is disabled, the
setting; the encoder
signal being sent to the
controls panning for
FireWire bus is pre-Fat
the selected input
Channel. The Dig Out
or output bus. When
button is only available
two channels are
when one of the channel
linked as stereo pair,
inputs is selected.
the LED display will
automatically change
to a stereo pan.
Overview 1
Map of Controls
Fat Channel 3-Band
The Fat Channel
Equalization is available
Compressor is
for all input and output
available for all
buses. All three bands
input and output
have variable center
buses.
frequencies (semi-
Threshold is
parametric), with 15 dB
variable from -56 to
boost/cut.
0 dB; Ratio from 1:1
to 14:1. Response
Low EQ band center
sets the attack
frequency is variable
and release tapers
from 36 to 465 Hz, with
simultaneously.
Shelf (shelving )or peak
Gain sets Makeup
(On) options.
Gain from 0 dB (no
gain adjustment) to
Mid EQ band center
+28 dB.
frequency is variable
from 26 Hz to 3.5 kHz,
with a default
Q of 0.55. HiQ
narrows the Q to
2.0.
High EQ band
center frequency
is variable from
1.4 to 18 kHz,
with Shelf
(shelving) or peak
(On) options.
Selected
Channel
shows you
which channel you are
adjusting with the Fat
Limiter is available for
all input and output Channel controls.
buses. Threshold is set
∞ Channel Copy, Load,
to 0 dBFS, with a :1
and Save buttons. Every
Ratio.
setting in the Fat Channel
can be copied from one
48V Phantom Power is
only available on the 12 to channel to another
and can be saved and
microphone preamps of
the input bus. stored as a user preset
that you can recall later.
Phase Reverse inverts
the signal 180˚ . It is only
available on the 16
channels of the input
bus.
7 7
English
Español
Deutsch
Français