Page 2
The material contained herein is for informational purposes only. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 3
The driver can be found in the enclosed Install the VGA driver as supplied by the VGA vendor. Install the VIA IDE driver version V2.1.26 or later version. The driver can be found in the enclosed CD. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Chapter 1 Introduction Chapter 1 Introduction This manual is designed to give you information on the TI7NBA motherboard. It is divided into the following sections: • • • • Introduction • • • • Specifications • • • • Hardware Description •...
Chapter 2 Specifications Chapter 2 Specifications The TI7NBA is a high-performance ATX motherboard with a Socket 370 connector for PPGA 370-type Pentium II processors. It offers flexibility in terms of CPU frequency and main memory type and size. The main features of the motherboard consist of the following:...
Page 9
One IrDA port Keyboard Controller Keyboard and Mouse Connectors PS/2 type USB Connector 2 ports onboard Win95-shut-off Allows shut-off control from within Windows 95 Modem-ring-on Supports PC powering on through an external modem. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 10
NOTE: For 440ZX chipset-based motherboard, there are three PCI Master 32-bit slots and one PCI slave 32-bit slot. The PCI slave slot is PCI4. Form Factor ATX, 12.05” x 7.09” (30.6cm x 18cm) TI7NBA Socket 370 ATX Motherboard User’s Manual...
Chapter 3 Hardware Description Chapter 3 Hardware Description This chapter briefly describes each of the major features of the TI7NBA motherboard. The layout of the board in Figure 1 shows the location of the key components. The topics covered in this chapter are as follows: 3.1 Processor ...................
Page 12
Chapter 3 Hardware Description Figure 1: Layout of the TI7NBA Motherboard TI7NBA Socket 370 ATX Motherboard User’s Manual...
3.3 Main Memory The TI7NBA motherboard supports three 168-pin DIMM (Dual In-line Memory Module) sockets to form a memory configuration from 8MB to 384MB. DIMM modules can be 8MB, 16MB, 32MB, 64MB and 128MB in SDRAM DRAM.
Chapter 3 Hardware Description 3.4 BIOS The BIOS on the TI7NBA motherboard provides the standard BIOS functions plus the following additional features: 1. ISA Plug and Play (PnP) Extension Unlike PCI cards that are Plug and Play, ISA cards require setting jumpers to resolve hardware conflicts.
Ultra DMA/33, the peak transfer rate can reach 33MB/sec. There are two IDE connectors - primary IDE and secondary IDE. With two devices per connector, up to four IDE devices can be supported. TI7NBA Socket 370 ATX Motherboard User’s Manual...
3.11 Hardware Monitoring IC The TI7NBA comes with the Winbond W83783 hardware monitoring IC. It monitors several hardware parameters including power supply voltages, fan speeds, and temperatures, which are very important for a high-end computer system to work stable and properly.
Page 18
Chapter 3 Hardware Description This page was intentionally left blank. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Chapter 4 Configuring the Motherboard Chapter 4 Configuring the Motherboard The following sections describe the necessary procedures and proper jumper settings to configure the TI7NBA motherboard. For the locations of the jumpers, refer to Figure 2. 4.1 CPU Frequency/Speed Setting ..........15 4.2 Clear CMOS Select: JP10 ............
Page 20
Chapter 4 Configuring the Motherboard Figure 2: Jumper Location on the TI7NBA TI7NBA Socket 370 ATX Motherboard User’s Manual...
JP10 Jumper Setting Function pin 1-2: short Normal 1 2 3 pin 2-3: short Clear CMOS NOTE: To clear CMOS, the ATX-power connector should be disconnected from the motherboard. TI7NBA Socket 370 ATX Motherboard User’s Manual...
4.3 Bus Speed Select: JP8 Use JP8, a 2-pin header, to configure the bus speed at 100MHz or by CPU Auto Detect. Jumper Setting Function open 100MHz bus speed short CPU Auto Detect TI7NBA Socket 370 ATX Motherboard User’s Manual...
Chapter 5 Installation Chapter 5 Installation This chapter describes the interface that the TI7NBA provides for creating a working system. Refer to Figure 3 for the location of the connectors. The following items are covered in this chapter: 5.1 I/O Connectors ................ 19 5.2 JP1: PS/2 Keyboard and PS/2 Mouse Connectors....
Page 24
Chapter 5 Installation Figure 3: Connector Location on the TI7NBA TI7NBA Socket 370 ATX Motherboard User’s Manual...
Chapter 5 Installation 5.1 I/O Connectors The I/O connectors connect the TI7NBA to the most common peripherals. To attach cables to these connectors, carefully align Pin 1 of the cables to that of the connectors. Refer to Figure 4 for the location and orientation of the connectors.
Chapter 5 Installation 5.3 J1, J2: Serial Ports The onboard serial ports of the TI7NBA, J1 and J2, are two DB-9 external connectors. The following table shows the pin-out assignments of these connectors. Signal Name Pin # Pin # Signal Name...
JP5 and JP6 are the onboard CD-ROM audio in connectors. Below are their pin assignments. 1 2 3 4 1 2 3 4 Signal Name Pin # Pin # Signal Name Ground Left Left Ground Ground Ground Right Right TI7NBA Socket 370 ATX Motherboard User’s Manual...
5.11 J19: AGP Fan Power Connector J19 is a 3-pin header for the AGP fan power connector. The fan must be a 12V fan. Pin # Signal Name Rotation +12V 1 2 3 Ground TI7NBA Socket 370 ATX Motherboard User’s Manual...
Ground Power good 5VSB +12V 5.13 J16: Floppy Drive Connector J16 of the TI7NBA is a 34-pin header and will support up to 2.88MB floppy drives. The following table shows its pin-out assignments. Signal Name Pin # Pin # Signal Name...
Power LED and Keylock: Pins 11 - 15 The power LED indicates the status of the main power switch. The keylock switch, when closed, will disable the keyboard function. Pin # Signal Name Power LED No connect Ground Keylock Ground TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 32
Reset Switch: Pins 9 and 19 The reset switch allows the user to reset the system without turning the main power switch Off and then On. Orientation is not required when making a connection to this header. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 33
Hard Disk Drive LED Connector: Pins 10 and 20 This connector connects to the hard drive activity LED on control panel. This LED will flash when the HDD is being accessed. Pin # Signal Name Ground TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 34
Chapter 5 Installation This page was intentionally left blank. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Report No FDD for WIN 95 Video BIOS Shadow C8000 - CBFFF Shadow/DC000 - DFFFF Shadow 6.5 Chipset Features Setup ............41 SDRAM RAS-to-CAS Delay SDRAM RAS Precharge Time SDRAM CAS Latency Time Bank DRAM Timing TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 36
HDD Power Down Throttle Duty Cycle PCI/VGA Act-Monitor Soft-Off by PWR-BTTN Resume by Alarm IRQ 8 Break Suspend Reload Global Timer Events PM Events 6.7 PNP/PCI Configuration ............50 PNP OS Installed Resources Controlled by TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 37
Onboard Serial/Parallel Port UART Mode Select Parallel Port Mode 6.12 Supervisor / User Password........... 59 6.13 IDE HDD Auto Detection ............. 60 6.14 Save & Exit Setup ..............61 6.15 Exit Without Saving .............. 61 TI7NBA Socket 370 ATX Motherboard User’s Manual...
<PgUp> and <PgDn> keys to change entries, <F1> for help and <Esc> to quit. When you enter the Setup utility, the Main Menu screen will appear on the screen. The Main Menu allows you to select from various setup functions and exit choices. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 39
We strongly recommend that you avoid making any changes to the chipset defaults. These defaults have been carefully chosen by both Award and your system manufacturer to provide the absolute maximum performance and reliability. TI7NBA Socket 370 ATX Motherboard User’s Manual...
1 to 12 Date : 1 to 31 Year : 1994 to 2079 To set the date, highlight the “Date” field and use the PageUp/ PageDown or +/- keys to set the current time. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 41
Number of sectors SIZE : Automatically adjust according to the configuration MODE (for IDE HDD only) : Auto Normal (HD < 528MB) Large (for MS-DOS only) (HD > 528MB and supports Logical Block Addressing) TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 42
The system boot will not be halted for a disk error; it will stop for all other errors. All, But Disk/Key The system boot will not be halted for a key- board or disk error; it will stop for all others. TI7NBA Socket 370 ATX Motherboard User’s Manual...
DRAM into cache memory, for even faster access by the CPU. These items allow you to enable (speed up memory access) or disable the cache function. By default, these items are Enabled. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 44
When disabled, continually holding down a key on your keyboard will generate only one instance. When enabled, you can set the two typematic controls listed next. By default, this field is set to Disabled. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 45
The default setting is No. Video BIOS Shadow This item allows you to change the Video BIOS location from ROM to RAM. Video Shadow will increase the video speed. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 46
Chapter 6 BIOS and System Setup C8000 - CBFFF Shadow/DC000 - DFFFF Shadow Shadowing a ROM reduces the memory available between 640KB to 1024KB. These fields determine whether optional ROM will be copied to RAM or not. TI7NBA Socket 370 ATX Motherboard User’s Manual...
SDRAM RAS-to-CAS Delay When DRAM is refreshed, both rows and columns are addressed separately. This field allows you to determine the timing of transition from Row Address Stove (RAS) to Column Address Strobe (CAS). TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 48
DRAM. The default setting is Enabled. Concurrent PCI/Host This field enables or disables the concurrent PCI/Host. The default setting is Disabled. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 49
16MB. By default, this field is set to Disabled. Passive Release When enabled, CPU to PCI bus accesses are allowed during passive release. Otherwise, the arbiter only accepts another PCI master access to local DRAM. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 50
Chapter 6 BIOS and System Setup TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 51
This field sets the value of the spread spectrum. Options are Disabled, 1.8% (CNTR), 0.6% (CNTR), 1.8% (DOWN), and 0.6% (DOWN). The default setting is Disabled. This field is for CE testing use only TI7NBA Socket 370 ATX Motherboard User’s Manual...
: Disabled F1 : Help PU/PD/+/- : Modify RTC Alarm Resume : Disabled F5 : Old Values (Shift) F2 : Color F6 : Load BIOS Defaults F7 : Load Setup Defaults VIA 82C693) (For TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 53
This field names the interrupt request (IRQ) line assigned to the modem (if any) on your system. Activity of the selected IRQ always awakens the system. By default, the IRQ is set to 3. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 54
BIOS to make the system more scheduleable. By default, this field is set to Disabled. IRQ 8 Break Suspend You can enable or disable the monitoring of IRQ 8 (Real Time Clock) so it does not awaken the system from Suspend mode. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 55
The IRQ section sets the wake-up call of the system. If activity is detected from any enabled IRQ channels in the left-hand group, the system wakes up from suspended mode. TI7NBA Socket 370 ATX Motherboard User’s Manual...
When enabled, this option delays PCI data transaction. By default, this field is set to Enabled. PCI#2 Access #1 Retry This item enables PC#2 Access #1 attempts. By default, this field is set to Disabled. TI7NBA Socket 370 ATX Motherboard User’s Manual...
IRQ service is being requested by a device. The default value is Level. Assign IRQ for USB/VGA These fields allow you to enable or disable the IRQ for USB and VGA. By default, these fields are enabled. TI7NBA Socket 370 ATX Motherboard User’s Manual...
: Select Item F10 : Save & Exit Setup (Shift) F2 : Change Color Load BIOS Defaults except Standard CMOS Setup To load SETUP defaults value to CMOS SRAM, enter “Y”. If not, enter “N”. TI7NBA Socket 370 ATX Motherboard User’s Manual...
(66x5), 366MHz (66x5.5), 400MHz (66x6), and 433MHz (66x6.5). Press the ↑ and ↓ keys to change the CPU speed or press the PageUp or PageDown key to see the selections for CPU Clock Multiplier and CPU Clock. TI7NBA Socket 370 ATX Motherboard User’s Manual...
By default, these fields are set to Disabled. Shutdown Temperature This field allows you to set the temperature at which the system automatically shuts down once it is reached, in order to avoid damage to system components. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Password, the user is allowed to set a password with a maximum of 5 characters. The system recognizes the size (lowercase/uppercase) of the characters entered. The third option is Hot Key Power ON. The keys Ctrl-F1 to Ctrl-F12 can be set to power on the system. TI7NBA Socket 370 ATX Motherboard User’s Manual...
This field determines the UART mode in your computer. The settings are Normal, IrDA and ASKIR. The default value is Normal. Parallel Port Mode This field allows you to determine parallel port mode function. Normal Printer Port Enhanced Parallel Port Extended Capabilities Port TI7NBA Socket 370 ATX Motherboard User’s Manual...
To accept the displayed entries, press the “Y” key to skip to the next drive, press the “N” key. If you accept the values, the parameters will appear listed beside the drive letter on the screen. TI7NBA Socket 370 ATX Motherboard User’s Manual...
For normal operations and to maximize the audio functions of the motherboard, follow the audio driver installation procedure below. Installing The Audio Drivers For Windows 95 Under Windows 95, click START => Setting => Control Panel. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 69
Chapter 7 Audio Driver Installation Guide Under the Control Panel window, click the System icon. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 74
Chapter 7 Audio Driver Installation Guide Insert the CD that comes with your motherboard into your CD-ROM drive. The following screen will appear. Now click Sound. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 76
11. Proceed with Setup to install the Windows 98 Drivers, Legacy DOS Drivers into your system. 12. After installation, the system will ask you to restart your computer for the changes to take effect. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 77
Chapter 7 Audio Driver Installation Guide This page was intentionally left blank. TI7NBA Socket 370 ATX Motherboard User’s Manual...
CPU temperature exceeds the safe limits, an alarm will be sounded; thereby preventing system crashing and ensuring overall stability. When System Monitor is initiated, the icon below appears in the task bar in the Windows environment. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 79
Clicking on the ‘X’ on the upper right corner would show you the latest company information or on any icon on the left side to display further information. The following section describes the different functions of System Monitor. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 80
Chapter 8 System Monitor Utility User’s Guide Computer - displays the operating working system version and processor type. Memory - displays the current memory usage status. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 81
Chapter 8 System Monitor Utility User’s Guide Hard Disk - displays the supported disk formats and disk space. Heat - displays the current rotational speed of CPU and Chassis fans, as well as the system and CPU temperatures. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 82
Chapter 8 System Monitor Utility User’s Guide Power - displays the current voltage status. NOTE: For Pentium II processors, System Monitor detects the VCC3 and VCCP values. For Pentium-level processors, System Monitor detects the VCORE and VIO values. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 83
Chapter 8 System Monitor Utility User’s Guide Log - displays errors occurring after System Monitor is started. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 84
Vio - 5% (Vio for P54C CPU is 3.5V. Vio for P55C is 3.3V.) Vcore- 5% * VCC3 / VIO and VCCP / VCORE values vary according to the processors used. Please contact the CPU manufacturer for further information. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 85
Chapter 8 System Monitor Utility User’s Guide This page was intentionally left blank. TI7NBA Socket 370 ATX Motherboard User’s Manual...
The following items are covered in this chapter: 9.1 Introduction ................81 9.2 Installation ................82 9.2.1 Installing the Local Version of LDCM 9.2.2 Installing the Administrative Version of LDCM LANDesk is a registered trademark of Intel Corporation. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Hardware System: a DMI BIOS is required for full LDCM functionality For network computers, the following requirements also apply: Protocols: IPX or IP (WinSock-enabled) communication protocol loaded on the client Hardware Interfaces: a network card for communication on the network TI7NBA Socket 370 ATX Motherboard User’s Manual...
During Setup, you will be asked to install Internet Explorer 3.02 in order to continue, or else Setup will be aborted. LDCM supports various languages and will default to English if it is unable to load ‘language.dl’.. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Double Click on ‘LANDesk Client Manager’ in the initial screen and the following screen will appear. Double click on the local version of LANDesk Client Manager. When the Welcome screen appears, click on “Next” to continue with Setup. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 90
Manager. Click “Browse” if you want to change the directory suggested. Otherwise, click “Next” to start installing LDCM. When Setup is finished, changes will have been made to the file AUTOEXEC.BAT. Restart your computer for the changes to take effect. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Click on “Next” to continue. The screen below allows you to install the documentation in Adobe Acrobat format and the Adobe Acrobat Reader software. Select the options you need and click on “Next” to start the installation. TI7NBA Socket 370 ATX Motherboard User’s Manual...
Page 92
Chapter 9 LANDesk User’s Guide After LANDesk Client Manager Setup is complete, restart your computer to be able to use the LANDesk Client Manager. TI7NBA Socket 370 ATX Motherboard User’s Manual...