1. Manuals
  2. Brands
  3. TMC Manuals
  4. Motherboard
  5. TI6NB+
  6. User manual

TMC TI6NB+ User Manual

T series pentium ii 440bx/apollo pro plus atx motherboard
Hide thumbs Also See for TI6NB+:
Table of Contents

Advertisement

Quick Links

Download this manual
TI6NB+
440BX/Apollo Pro Plus
ATX Motherboard
User's Manual
Version 1.1

Advertisement

Table of Contents
loading

Related Manuals for TMC TI6NB+

Summary of Contents for TMC TI6NB+

  • Page 1 TI6NB+ 440BX/Apollo Pro Plus ATX Motherboard User's Manual Version 1.1...
  • Page 2 The brand names, product names and trade names in this manual are trademarks or registered trademarks of their respective holders. This publication is protected by copyright and all rights are reserved. No part of it may be reproduced or transmitted by any means or in any form, without prior consent in writing from the manufacturer.

  • Page 3: Table Of Contents

    Contents Contents Chapter 1 Introduction............ 1 Chapter 2 Specifications ..........3 Chapter 3 Hardware Description ........5 3.1 Processor ................... 7 3.2 L2 Cache ................... 7 3.3 Main Memory................7 3.4 BIOS..................8 3.5 I/O Port Address Map..............9 3.6 DMA Channels................9 3.7 Interrupt Request (IRQ) Lines ..........
  • Page 4 Contents Chapter 6 BIOS and System Setup....... 29 6.1 BIOS Introduction ..............32 6.2 BIOS Setup ................32 6.3 Standard CMOS Setup.............34 6.4 BIOS Features Setup..............37 6.5 Chipset Features Setup.............41 6.6 Power Management Setup ............44 6.7 PNP/PCI Configuration ............48 6.8 Load BIOS Defaults ..............51 6.9 Load Setup Defaults..............51 6.10 CPU Speed Setting ..............52 6.11 Integrated Peripherals ............55...

  • Page 5: Chapter 1 Introduction

    Chapter 1 Introduction Chapter 1 Introduction This manual is designed to give you information on the TI6NB+ motherboard. It is divided into the following sections: Introduction Specifications Hardware Description Configuring the Motherboard Installation BIOS and System Setup System Monitor Utility User’s Guide LANDesk User’s Guide Checklist Please check that your package is complete and contains the items below.
  • Page 6 Contents This page was intentionally left blank. TI6NB+ Pentium II 440BX ATX Motherboard User’s Manual...

  • Page 7: Chapter 2 Specifications

    Chapter 2 Specifications Chapter 2 Specifications The TI6NB+ is a high-performance ATX 440BX/Apollo Pro Plus motherboard with a Slot 1 connector for Pentium II processors. It offers flexibility in terms of CPU frequency and main memory type and size. The main features of the motherboard consist of the following: CPU Socket Slot 1 Processor...
  • Page 8 Chapter 3 Hardware Description DMI BIOS Support Desktop Management Interface (DMI) allows users to download system hardware-level information such as CPU type, CPU speed, internal/external frequencies and memory size. PCI Bus Master IDE Controller (Ultra DMA/33) Onboard PCI Bus Master IDE (Ultra DMA/33) controller with two connectors for up to four IDE devices in two channels, supporting enhanced IDE devices such as Tape Backup and CD-ROM drives, PIO Mode 3/4 and Bus Mastering Ultra DMA/33 (You have to install...

  • Page 9: Chapter 3 Hardware Description

    Chapter 3 Hardware Description Chapter 3 Hardware Description This chapter briefly describes each of the major features of the TI6NB+ motherboard. The layout of the board in Figure 1 shows the location of the key components. The topics covered in this chapter are as follows: 3.1 Processor ...................
  • Page 10 Chapter 3 Hardware Description Figure 1: Layout of the TI6NB+ Motherboard TI6NB+ Pentium II 440BX ATX Motherboard User’s Manual...

  • Page 11: Processor

    Chapter 3 Hardware Description 3.1 Processor The TI6NB+ motherboard is designed to take a Pentium II processor running 233/266/300/333MHz (Klamath/Celeron/Deschutes) at 66MHz CPU bus speed or 300/350/400/450MHz (Deschutes) at 100MHz CPU bus speed with its Slot 1 processor connector. 3.2 L2 Cache The L2 cache is integrated in the Pentium II processor.

  • Page 12: Bios

    Chapter 3 Hardware Description 168-pin DIMM (3.3V) SDRAM Onboard DIMM3 DIMM2 DIMM1 Total Memory SDRAM 64MB ----- ----- ----- 64MB 64MB 32MB ----- ----- 96MB 64MB 32MB 32MB ----- 128MB 64MB 32MB 32MB 32MB 160MB 64MB 64MB ----- ----- 128MB 64MB 64MB 32MB...

  • Page 13: I/O Port Address Map

    Chapter 3 Hardware Description 3.5 I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. There is a total of 1K port address space available. The following table lists the I/O port addresses used on the motherboard.

  • Page 14: Interrupt Request (Irq) Lines

    Chapter 3 Hardware Description 3.7 Interrupt Request (IRQ) Lines There is a total of 15 IRQ lines available on the motherboard. Peripheral devices use an interrupt request to notify the CPU for the service required. The following table shows the IRQ lines used by the devices on the motherboard: Level Function...

  • Page 15: Onboard Multi-I/O

    Chapter 3 Hardware Description 3.9 Onboard Multi-I/O The onboard multi-I/O chip, W83977TF, supports a keyboard controller (AMI copyright), two serial ports, one parallel port, one floppy controller and one IrDA port. The serial ports are 16550 UART compatible. The parallel port features high-speed EPP/ECP mode. The floppy controller supports up to 2.88 MB format.
  • Page 16 Chapter 3 Hardware Description This page was intentionally left blank. TI6NB+ Pentium II 440BX ATX Motherboard User’s Manual...

  • Page 17: Chapter 4 Configuring The Motherboard

    Chapter 4 Configuring the Motherboard Chapter 4 Configuring the Motherboard The following sections describe the necessary procedures and proper jumper settings to configure the TI6NB+ motherboard. For the locations of the jumpers, refer to Figure 2. 4.1 CPU Frequency Setting ............15 4.2 AGP Clock Setting: JP6, JP8...........
  • Page 18 Chapter 4 Configuring the Motherboard Figure 2: Jumper Location on the TI6NB+ TI6NB+ Pentium II 440BX ATX Motherboard User’s Manual...

  • Page 19: Cpu Frequency Setting

    Chapter 4 Configuring the Motherboard 4.1 CPU Frequency Setting The TI6NB+ motherboard allows users to set the CPU speed through the BIOS. The parameters in setting the CPU speed include CPU Clock Multiplier and CPU Clock/PCI Clock. In the initial setup, the system automatically detects the bus speed (front side bus) of the CPU (66MHz or 100MHz).

  • Page 20: Agp Clock Setting: Jp6, Jp8

    Chapter 4 Configuring the Motherboard 4.2 AGP Clock Setting: JP6, JP8 JP6 and JP8 (found only in motherboard versions 1.00 and above) can be used to set the AGP clock to run the ‘normal’ AGP clock or AGP clock synchronous with the CPU clock. Refer to the table below. AGP Clock Normal Synchronous w/...

  • Page 21: Chapter 5 Installation

    Chapter 5 Installation Chapter 5 Installation This chapter describes the interface that the TI6NB+ provides for creating a working system. Refer to Figure 3 for the location of the connectors. The following items are covered in this chapter: 5.1 I/O Connectors ................ 19 5.2 J1: PS/2 Keyboard and PS/2 Mouse Connectors.....
  • Page 22 Chapter 5 Installation Figure 3: Connector Location on the TI6NB+ TI6NB+ Pentium II 440BX ATX Motherboard User’s Manual...

  • Page 23: I/O Connectors

    Chapter 5 Installation 5.1 I/O Connectors The I/O connectors connect the TI6NB+ to the most common peripherals. To attach cables to these connectors, carefully align Pin 1 of the cables to that of the connectors. Refer to Figure 4 for the location and orientation of the connectors.

  • Page 24: J8: Atx Power Supply Connector

    Chapter 5 Installation 5.3 J8: ATX Power Supply Connector J8 is a 20-pin ATX power supply connector. Refer to the following table for the pin out assignments. (Use an ATX power supply with 3.3V power.) Signal Name Pin # Pin # Signal Name 3.3V 3.3V...

  • Page 25: J2, J3: Serial Ports

    Chapter 5 Installation 5.6 J2, J3: Serial Ports The onboard serial ports of the TI6NB+, J2 and J3, are two DB-9 external connectors. The following table shows the pin-out assignments of the these connectors. Signal Name Pin # Pin # Signal Name DCD, Data carrier detect DSR, Data set ready...

  • Page 26: J4: Parallel Port Connector

    Chapter 5 Installation 5.7 J4: Parallel Port Connector J4 is a DB-25 external connector as seen in the above figure. The following table describes the pin- out assignments of this connector. Signal Name Pin # Pin # Signal Name Line printer strobe AutoFeed PD0, parallel data 0 Error...

  • Page 27: J5: Floppy Drive Connector

    Chapter 5 Installation 5.9 J5: Floppy Drive Connector J5 of the TI6NB+ is a 34-pin header and will support up to 2.88MB floppy drives. The following table shows its pin-out assignments. Signal Name Pin # Pin # Signal Name Ground RM/LC Ground No connect...

  • Page 28: J19, J18: Eide Connectors

    Chapter 5 Installation 5.10 J19, J18: EIDE Connectors J19: Primary IDE Connector Signal Name Pin # Pin # Signal Name Reset IDE Ground Host data 7 Host data 8 Host data 6 Host data 9 Host data 5 Host data 10 Host data 4 Host data 11 Host data 3...

  • Page 29: J20: Front Bezel Connectors

    Chapter 5 Installation 5.11 J20: Front Bezel Connectors The front bezel of the case has a control panel which provides light indication of the computer activities and switches to change the computer status. J20 is a 20-pin header that provides interfaces for the following functions.
  • Page 30 Chapter 5 Installation SMI/Hardware Switch: Pins 6 and 16 This connector supports the "Green Switch" on the control panel, which, when pressed, will force the system board into the power-saving mode immediately. Pin # Signal Name Sleep Ground ATX Power ON Switch: Pins 7 and 17 This 2-pin connector is an “ATX Power Supply On/Off Switch”...

  • Page 31: J21: Chassis Fan Power Connector

    Chapter 5 Installation Hard Disk Drive LED Connector: Pins 10 and 20 This connector connects to the hard drive activity LED on control panel. This LED will flash when the HDD is being accessed. Pin # Signal Name Ground 5.12 J21: Chassis Fan Power Connector J21 is a 3-pin header for the chassis fan power connector.

  • Page 32: Jp5: Sb-Link Connector

    Chapter 5 Installation 5.15 JP5: SB-Link Connector The following table shows the pin out assignments of this connector. This connector is used for the Creative Sound AWE64D PCI sound card. The SB-Link uses Intel’s PC-PCI technology to deliver (Creative’s) Sound Blaster 16 compatibility to AWE64D, enabling users to play Real-mode DOS games.

  • Page 33: Chapter 6 Bios And System Setup

    Chapter 6 BIOS and System Setup Chapter 6 BIOS and System Setup This chapter describes the different settings available in the Award BIOS. The topics covered in this chapter are as follows: 6.1 BIOS Introduction ..............32 6.2 BIOS Setup................32 6.3 Standard CMOS Setup ............
  • Page 34 Chapter 6 BIOS and System Setup Bank DRAM Timing SDRAM Cycle Length DRAM Clock Select DRAM Data Integrity Mode Read Around Write Concurrent PCI/Host System BIOS Cacheable Video BIOS Cacheable Video RAM Cacheable 8 Bit I/O Recovery Time 16 Bit I/O Recovery Time Memory Hole at 15MB - 16MB Passive Release Delayed Transaction...
  • Page 35 Chapter 6 BIOS and System Setup PCI Dynamic Bursting PCI Master 0 WS Write PCI Delay Transaction PCI#2 Access #1 Retry AGP Master 1 WS Write AGP Master 1 WS Read PCI IRQ Activated by Assign IRQ for USB/VGA 6.8 Load BIOS Defaults ..............51 6.9 Load Setup Defaults ..............

  • Page 36: Bios Introduction

    Chapter 6 BIOS and System Setup 6.1 BIOS Introduction The Award BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel Pentium II processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial and parallel ports. It also adds virus and password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.
  • Page 37 Chapter 6 BIOS and System Setup ROM PCI/ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE, INC. CPU SPEED SETTING STANDARD CMOS SETUP BIOS FEATURES SETUP INTEGRATED PERIPHERALS CHIPSET FEATURES SETUP SUPERVISOR PASSWORD POWER MANAGEMENT SETUP USER PASSWORD PNP/PCI CONFIGURATION IDE HDD AUTO DETECTION LOAD BIOS DEFAULTS SAVE &...

  • Page 38: Standard Cmos Setup

    Chapter 6 BIOS and System Setup 6.3 Standard CMOS Setup “Standard CMOS Setup” choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling. If the motherboard is already installed in a working system, you will not need to select this option.
  • Page 39 Chapter 6 BIOS and System Setup Time The time format is: Hour : 00 to 23 Minute : 00 to 59 Second : 00 to 59 To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn> or +/- keys to set the current time. Primary HDDs / Secondary HDDs The onboard PCI IDE connectors provide Primary and Secondary channels for connecting up to four IDE hard disks or other IDE devices.
  • Page 40 Chapter 6 BIOS and System Setup NOTE: The specifications of your drive must match with the drive table. The hard disk will not work properly if you enter incorrect information in these fields. If your hard disk drive type is not matched or listed, you can use Type User to define your own drive type manually.

  • Page 41: Bios Features Setup

    Chapter 6 BIOS and System Setup 6.4 BIOS Features Setup This section allows you to configure and improve your system and allows you to set up some system features according to your preference. ROM / PCI ISA BIOS BIOS FEATURES SETUP AWARD SOFTWARE, INC.
  • Page 42 Chapter 6 BIOS and System Setup Virus Warning This item protects the boot sector and partition table of your hard disk against accidental modifications. If an attempt is made, the BIOS will halt the system and display a warning message. If this occurs, you can either allow the operation to continue or run an anti-virus program to locate and remove the problem.

  • Page 43: Ide Hdd Block Mode

    Chapter 6 BIOS and System Setup Boot Up Floppy Seek When enabled, the BIOS will seek whether or not the floppy drive installed has 40 or 80 tracks. 360K type has 40 tracks while 760K, 1.2M and 1.44M all have 80 tracks. By default, this field is set to Enabled. Boot Up NumLock Status This allows you to activate the NumLock function after you power up the system.
  • Page 44 Chapter 6 BIOS and System Setup PCI/VGA Palette Snoop Some non-standard VGA display cards may not show colors properly. This field allows you to set whether or not MPEG ISA/VESA VGA Cards can work with PCI/VGA. When this field is enabled, a PCI/VGA can work with an MPEG ISA/VESA VGA card.

  • Page 45: Chipset Features Setup

    Chapter 6 BIOS and System Setup 6.5 Chipset Features Setup This Setup menu controls the configuration of the motherboard chipset. ROM PCI/ISA BIOS CHIPSET FEATURES SETUP AWARD SOFTWARE INC. SDRAM RAS-to-CAS Delay SDRAM RAS Precharge Time SDRAM CAS Latency Time : Disabled SDRAM Precharge Control DRAM Integrity Mode...
  • Page 46 Chapter 6 BIOS and System Setup SDRAM RAS Precharge Time The precharge time is the number of cycles it takes for the RAS to accumulate its charge before DRAM refresh. If insufficient time is allowed, refresh may be incomplete and the DRAM may fail to retain data.
  • Page 47 Chapter 6 BIOS and System Setup Video RAM Cacheable Selecting Enabled allows caching of the video BIOS ROM at C0000h to C7FFFh, resulting in better video performance. However, if any program writes to this memory area, a memory access error may result. 8 Bit I/O Recovery Time This option specifies the length of the delay (in sysclks) inserted between consecutive 8-bit I/O operations.

  • Page 48: Power Management Setup

    Chapter 6 BIOS and System Setup Spread Spectrum This field sets the value of the spread spectrum. Options are Disabled, 1.8% (CNTR), 0.6% (CNTR), 1.8% (DOWN), and 0.6% (DOWN). The default setting is Disabled. This field is for CE testing use only OnChip USB The OnChip USB can be enabled to allow support for USB keyboards.
  • Page 49 Chapter 6 BIOS and System Setup ROM PCI/ISA BIOS POWER MANAGEMENT SETUP AWARD SOFTWARE, INC. ACPI Function : Enabled Primary INTR : ON Power Management : User Define IRQ3 (COM2) : Primary PM Control by APM : Yes IRQ4 (COM1) : Primary Video Off Option : Suspend...
  • Page 50 Chapter 6 BIOS and System Setup Video Off Method This field defines the Video Off features. There are three options. V/H SYNC + Blank Default setting, blank the screen and turn off vertical and horizontal scanning. DPMS Allows the BIOS to control the video display card if it supports the DPMS feature.
  • Page 51 Chapter 6 BIOS and System Setup Soft-Off by PWR-BTTN This field defines the power-off mode when using an ATX power supply. The Instant-Off mode allows powering off immediately upon pressing the power button. In the Delay 4 Sec mode, the system powers off when the power button is pressed for more than four seconds or places the system in a very low-power-usage state, with only enough circuitry receiving power to detect power button activity when pressed for less...

  • Page 52: Pnp/Pci Configuration

    Chapter 6 BIOS and System Setup 6.7 PNP/PCI Configuration This option configures the PCI bus system. All PCI bus systems on the system use INT#, thus all installed PCI cards must be set to this value. ROM PCI/ISA BIOS PNP/PCI CONFIGURATION AWARD SOFTWARE INC.
  • Page 53 Chapter 6 BIOS and System Setup PNP OS Installed This field allows you to specify if the operating system installed in your system is plug and play aware. NOTE: Operating systems such as DOS, OS/2, and Windows 3.x do not use PnP Resources Controlled by This PnP BIOS can configure all of the boot and compatible devices automatically.
  • Page 54 Chapter 6 BIOS and System Setup AGP Master 1 WS Write When enabled, writes to the AGP bus are executed with 1 wait states. By default, this field is set to Enabled. AGP Master 1 WS Read When enabled, reads to the AGP bus are executed with 1 wait states. By default, this field is set to Enabled.

  • Page 55: Load Bios Defaults

    Chapter 6 BIOS and System Setup 6.8 Load BIOS Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non-optimal and disable all high-performance features. ROM PCI/ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE, INC.

  • Page 56: Cpu Speed Setting

    Chapter 6 BIOS and System Setup 6.10 CPU Speed Setting This Setup menu controls the configuration of the motherboard chipset. ROM PCI/ISA BIOS CPU SPEED SETTING AWARD SOFTWARE INC. CPU Speed : Manual CPU Clock Multiplier : X 3.5 CPU/PCI Clock Select : 100/33 MHz : 66 C/151 F CPU Warning Temperature...
  • Page 57 Chapter 6 BIOS and System Setup CPU Speed, CPU Clock Multiplier, CPU/PCI Clock Select The TI6NB+ motherboard allows users to set the CPU speed through the BIOS. The parameters in setting the CPU speed include CPU Clock Multiplier and CPU Clock/PCI Clock. In the initial setup, the system automatically detects the bus speed (front side bus) of the CPU (66MHz or 100MHz).
  • Page 58 Chapter 6 BIOS and System Setup Current System/ CPU/Chips / VGA Temperatures These read-only fields reflect the functions of the hardware thermal sensor that monitors the chip blocks and system temperatures to ensure the system is stable. Current CPU Fan Speed/Chassis Fan Speed These read-only fields show the current speeds in RPM (revolution per minute) for the CPU fan and chassis fan as monitored by the hardware monitoring IC.

  • Page 59: Integrated Peripherals

    Chapter 6 BIOS and System Setup 6.11 Integrated Peripherals This option sets your hard disk configuration, mode and port. ROM PCI/ISA BIOS INTEGRATED PERIPHERALSP AWARD SOFTWARE INC. IDE HDD Block Mode : Enabled Onboard FDC Controller : Enabled IDE Primary Master PIO : Auto Onboard Serial Port 1 : 3F8/IRQ4...
  • Page 60 Chapter 6 BIOS and System Setup IDE HDD Block Mode This field allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive. IDE HDD Prefetch Mode This field enables or disables the IDE hard disk’s prefetch mode. IDE Primary/Secondary Master/Slave PIO These fields allow your system hard disk controller to work faster.
  • Page 61 Chapter 6 BIOS and System Setup Onboard Serial/Parallel Port These fields allow you to select the onboard serial and parallel ports and their addresses. The default values for these ports are: Serial Port 1 3F8/IRQ4 Serial Port 2 2F8/IRQ3 Parallel Port 378H/IRQ7 UART Mode Select This field determines the UART mode in your computer.

  • Page 62: Supervisor / User Password

    Chapter 6 BIOS and System Setup 6.12 Supervisor / User Password These two options set the system password. Supervisor Password sets a password that will be used to protect the system and Setup utility. User Password sets a password that will be used exclusively on the system. To specify a password, highlight the type you want and press <Enter>.

  • Page 63: Ide Hdd Auto Detection

    Chapter 6 BIOS and System Setup 6.13 IDE HDD Auto Detection This option detects the parameters of an IDE hard disk drive, and automatically enters them into the Standard CMOS Setup screen. ROM PCI/ISA BIOS STANDARD CMOS SETUP AWARD SOFTWARE, INC. HARD DISKS TYPE SIZE...

  • Page 64: Save & Exit Setup

    Chapter 6 BIOS and System Setup 6.14 Save & Exit Setup This option allows you to determine whether or not to accept the modifications. If you type “Y”, you will quit the setup utility and save all changes into the CMOS memory. If you type “N”, you will return to Setup utility.

  • Page 65: Chapter 7 System Monitor Utility User's Guide

    Chapter 7 System Monitor Utility User’s Guide Chapter 7 System Monitor Utility User’s Guide This chapter introduces System Monitor Utility that comes with the motherboard in conjunction with the onboard hardware monitoring IC. The sections below give the functions of the utility. System Monitor is a software utility that oversees the general performance of systems, covering areas like system temperature, system voltage, CPU and system fan rotational speeds.
  • Page 66 Chapter 7 System Monitor Utility User’s Guide The following screen appears upon clicking on the System Monitor icon. Clicking on the ‘X’ on the upper right corner would show you the latest company information or on any icon on the left side to display further information.
  • Page 67 Chapter 7 System Monitor Utility User’s Guide Computer - displays the operating working system version and processor type. Memory - displays the current memory usage status. TI6NB+ Pentium II 440BX ATX Motherboard User’s Manual...
  • Page 68 Chapter 7 System Monitor Utility User’s Guide Hard Disk - displays the supported disk formats and disk space. Heat - displays the current rotational speed of CPU and Chassis fans, as well as the system and CPU temperatures. TI6NB+ Pentium II 440BX ATX Motherboard User’s Manual...
  • Page 69 Chapter 7 System Monitor Utility User’s Guide Power - displays the current voltage status. NOTE: For Pentium II processors, System Monitor detects the VCC3 and VCCP values. For Pentium-level processors, System Monitor detects the VCORE and VIO values. Log - displays errors occurring after System Monitor is started. TI6NB+ Pentium II 440BX ATX Motherboard User’s Manual...
  • Page 70 Chapter 7 System Monitor Utility User’s Guide Alarm - sets the values at which an alarm is sounded. Voltage : the acceptable voltage range between the "Hi Limit” and "Lo Limit" value. Temperature : temperature threshold. Fan Rotation Speed : the minimum rotation speed. NOTE: Intel has defined a margin of difference for the voltages as below: 12 Volts - 10% (10.8V ~ 13.2V) 5 Volts - 5% (4.75 ~ 5.25%)

  • Page 71: Chapter 8 Landesk User's Guide

    Chapter 8 LANDesk User’s Guide Chapter 8 LANDesk User’s Guide This chapter gives a brief introduction to the optional LANDesk Client Manager (LDCM) utility, as well as the installation procedures. The following items are covered in this chapter: 8.1 Introduction ................68 8.2 Installation ................

  • Page 72: Introduction

    Chapter 8 LANDesk User’s Guide 8.1 Introduction LANDesk Client Manager* provides the capability for managing components (network interface cards, memory, printers, software applications, etc.) within a PC system. It uses the Desktop Management Interface (DMI) standard established by the Desktop Management Task Force (DMTF).

  • Page 73: Installation

    Chapter 8 LANDesk User’s Guide 8.2 Installation The optional LANDesk utility that comes with the CPU card runs in Windows NT or Windows 95 operating system. Upon entering the Windows NT 4.0 or Windows 95 environment, insert the CD. Windows will autorun the installation program and show the following screen.

  • Page 74: Installing The Local Version Of Ldcm

    Chapter 8 LANDesk User’s Guide 8.2.1 Installing the Local Version of LDCM Double Click on ‘LANDesk Client Manager’ in the initial screen and the following screen will appear. Double click on the local version of LANDesk Client Manager. When the Welcome screen appears, click on “Next” to continue with Setup.
  • Page 75 Chapter 8 LANDesk User’s Guide Choose the directory location where Setup will install LANDesk Client Manager. Click “Browse” if you want to change the directory suggested. Otherwise, click “Next” to start installing LDCM. When Setup is finished, changes will have been made to the file AUTOEXEC.BAT.

  • Page 76: Installing The Administrative Version Of Ldcm

    Chapter 8 LANDesk User’s Guide 8.2.2 Installing the Administrative Version of LDCM After double clicking on ‘LANDesk Client Manager’ in the initial screen, select the administrative version of the LDCM and the Welcome screen below will appear. Click on “Next” to continue. The screen below allows you to install the documentation in Adobe Acrobat format and the Adobe Acrobat Reader software.
  • Page 77 Chapter 8 LANDesk User’s Guide After LANDesk Client Manager Setup is complete, restart your computer to be able to use the LANDesk Client Manager. TI6NB+ Pentium II 440BX ATX Motherboard User’s Manual...

  • Page 78: Appendix

    Appendix Appendix A. Slot 1 Retention Mechanism The retention mechanism that comes with your motherboard, as seen in the above figure, accommodates all kinds of Pentium II processors. For Celeron processors, place the two caps supplied on both ends after installing the processor to secure the installation.

  • Page 79: Additions & Errata

    Appendix B. Additions & Errata This section is allotted for future page inserts containing any additional information or correction that the users should know. TI6NB+ Pentium II 440BX ATX Motherboard User’s Manual...

Table of Contents