Advertisement
Quick Links
Advertisement
Related Manuals for Classe Audio CAM-200
Summary of Contents for Classe Audio CAM-200
- Page 1 OWNER’S MANUAL CAM-200 Mono Power Amplifier...
- Page 2 CLASSÉ DESIGN PHILOSOPHY 1. REPEATED LISTENING DESIGN SESSIONS: Fine tuning of sound by exchanging and mixing of parts (transistors, capacitors, wiring, PCB boards etc.), and adjusting many specific operating voltages within proper engineering ranges, producing an overall sonic recipe giving the most natural harmonic realism of music typical of instruments in a live performance.
-
Page 3: Table Of Contents
CAM200 OWNER'S MANUAL TABLE OF CONTENTS UNPACKING & SET-UP……………………………………………………..…… 4 GENERAL CONNECTIONS ………………………………………………….….. 5 CONNECTIONS FOR REGULAR OR BALANCED INPUTS ………………….. 8 PROTECTION CIRCUIT …………………………………………………………. 9 CAM200 BACK VIEW …………………………………………………………… 10 CAM200 TOP VIEW ……………………………………………………………… 11 SPECIFICATIONS ………………………………………………………………... -
Page 4: Unpacking & Set-Up
UNPACKING & SET-UP Your CLASSÉ CAM200 power amplifier is packed in high density, semi-rigid foam placed in a special cardboard box. Take it out of the plastic bag and inspect the unit for any concealed damage. Apart from this owner's manual, please ensure the following has also been included: 1) Detachable A.C. -
Page 5: General Connections
GENERAL CONNECTIONS A.C. LINE Insert the linecord into the A.C. receptacle on the rear of the unit. PLEASE MAKE SURE YOU HAVE PREVIOUSLY HOOKED UP THE SPEAKERS AND PREAMPLIFIER TO YOUR AMPLIFIER BEFORE CONNECTING THE AC POWER CORD TO THE AMPLIFIER. - Page 6 IR OUT and IN The CAM200 can be turned ON /OFF using a +5VDC trigger or with remote control code via the IR IN jack located at the rear of the unit. The IR OUT is the loop out of the incoming signal from IR IN.
- Page 7 IR OUT and IN (Continued) The remote control system is RECS80 with the system code 5 and the command codes is as follows: AMP1 _____ 24 AMP4 _____ 27 AMP2 _____ 25 AMP5 _____ 34 AMP3 _____ 26 AMP6 _____ 35 These command codes will toggle the CAM200 ON/OFF.
-
Page 8: Connections For Regular Or Balanced Inputs
CONNECTIONS FOR REGULAR OR BALANCED INPUTS: The CLASSÉ CAM200 power amplifier is equipped with both regular and balanced inputs, either one may be used . Be sure that the CAM200 is SEPARATELY, BUT NOT SIMULTANEOUSLY OFF before changing any connections. When the amplifier is shipped from Classé, there is a jumper at the balanced input (XLR) between pin 1 and 3. -
Page 9: Protection Circuit
PROTECTION CIRCUIT The Classé CAM200 equipped with a rail currents sensors to protect the output drivers under extreme condition such as short output, and Mosfet fuses (2AG 1/2 PT, 1/2 amp fast blow) to protect the Mosfets, which are used as pre-drivers for the output stage of the amplifier. Also the CAM200 has an output DC sensor;... -
Page 10: Cam200 Back View
Fig 1: CAM200 back view... -
Page 11: Cam200 Top View
Fig 2: CAM200 top view... - Page 12 CLASSÉ AUDIO 5070 François Cusson Lachine, Quebec Canada H8T 1B3 Telephone: 514 636 63 84 Fax: 514 636 14 28...
-
Page 13: Specifications
CLASSE CAM200 ULTRA HIGH CURRENT MONORAL POWER AMPLIFIER FEATURES AND SPECIFICATIONS SHEET CAM200 FEATURES: Newly developed special Classé "UHC TRANSFER" power supply section. Current capacity increased above standard units. All new Classé PCB circuit boards with "UHC TRANSFER" characteristics. True symmetrical, differential amplifier circuits from input to output. Thick brushed Soft Shadow Silver faceplate with Satin Black middle plate. - Page 14 Notice to all Classé Product owners: Thank you for your purchase of a Classé Audio component. All of us at Classé have taken extreme care to ensure that your purchase will become a prized investment. We are proud to inform you that all Classé Audio components have been officially approved for the European Community CE mark.