Download
Share
Print this page
Classe Audio CAM-200 Owner's Manual
  1. Manuals
  2. Brands
  3. Classe Audio Manuals
  4. Amplifier
  5. CAM-200
  6. Owner's manual
Classe Audio CAM-200 Owner's Manual

Classe Audio CAM-200 Owner's Manual

Mono power amplifier
Hide thumbs Also See for CAM-200:

Advertisement

Quick Links

See also: Service Manual
OWNER'S MANUAL
CAM-200
Mono Power Amplifier

Advertisement

loading
Need help?

Need help?

Do you have a question about the CAM-200 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Classe Audio CAM-200

Summary of Contents for Classe Audio CAM-200

  • Page 1 OWNER’S MANUAL CAM-200 Mono Power Amplifier...
  • Page 2 CLASSÉ DESIGN PHILOSOPHY 1. REPEATED LISTENING DESIGN SESSIONS: Fine tuning of sound by exchanging and mixing of parts (transistors, capacitors, wiring, PCB boards etc.), and adjusting many specific operating voltages within proper engineering ranges, producing an overall sonic recipe giving the most natural harmonic realism of music typical of instruments in a live performance.

  • Page 3: Table Of Contents

    CAM200 OWNER'S MANUAL TABLE OF CONTENTS UNPACKING & SET-UP……………………………………………………..…… 4 GENERAL CONNECTIONS ………………………………………………….…. 5 CONNECTIONS FOR REGULAR OR BALANCED INPUTS ………..….. 8 PROTECTION CIRCUIT …………………………………………………………. 9 CAM200 BACK VIEW …………………………………………………………… 10 CAM200 TOP VIEW ……………………………………………………………… 11 SPECIFICATIONS ………………………………………………………………... UNPACKING & SET-UP...

  • Page 4: General Connections

    Your CLASSÉ CAM200 power amplifier is packed in high density, semi-rigid foam placed in a special cardboard box. Take it out of the plastic bag and inspect the unit for any concealed damage. Apart from this owner's manual, please ensure the following has also been included: 1) Detachable A.C.
  • Page 5 Insert the linecord into the A.C. receptacle on the rear of the unit. PLEASE MAKE SURE YOU HAVE PREVIOUSLY HOOKED UP THE SPEAKERS AND PREAMPLIFIER TO YOUR AMPLIFIER BEFORE CONNECTING THE AC POWER CORD TO THE AMPLIFIER. CAUTION: SAFETY INSTRUCTIONS DISCONNECT AC LINE CABLE WHILE MAKING ALL CONNECTIONS.
  • Page 6 The CAM200 can be turned ON /OFF using a +5VDC trigger or with remote control code via the IR IN jack located at the rear of the unit. The IR OUT is the loop out of the incoming signal from IR IN.

  • Page 7: Connections For Regular Or Balanced Inputs

    The remote control system is RECS80 with the system code 5 and the command codes is as follows: AMP1 _____ 24 AMP4 _____ 27 AMP2 _____ 25 AMP5 _____ 34 AMP3 _____ 26 AMP6 _____ 35 These command codes will toggle the CAM200 ON/OFF. To turn all six of the amplifier ON and OFF the following code should be used: ALL ON_____08 ALL OFF_____9...

  • Page 8: Protection Circuit

    The CLASSÉ CAM200 power amplifier is equipped with both regular and balanced inputs, either one may be used . Be sure that the CAM200 is SEPARATELY, BUT NOT SIMULTANEOUSLY OFF before changing any connections. When the amplifier is shipped from Classé, there is a jumper at the balanced input (XLR) between pin 1 and 3.
  • Page 9 The Classé CAM200 equipped with a rail currents sensors to protect the output drivers under extreme condition such as short output, and Mosfet fuses (2AG 1/2 PT, 1/2 amp fast blow) to protect the Mosfets, which are used as pre-drivers for the output stage of the amplifier. Also the CAM200 has an output DC sensor, this will put the CAM200 on protection mode in the event DC occurs at the output of the amplifier or heavy clipping of output signals.

  • Page 10: Cam200 Back View

    Fig 1: CAM200 back view...

  • Page 11: Cam200 Top View

    Fig 2: CAM200 top view...
  • Page 12 CLASSÉ AUDIO 5070 François Cusson Lachine, Quebec Canada H8T 1B3 Telephone: 514 636 63 84 Fax: 514 636 14 28...

  • Page 13: Specifications

    CLASSE CAM200 ULTRA HIGH CURRENT MONORAL POWER AMPLIFIER FEATURES AND SPECIFICATIONS SHEET CAM200 FEATURES: Newly developed special Classé "UHC TRANSFER" power supply section. Current capacity increased above standard units. All new Classé PCB circuit boards with "UHC TRANSFER" characteristics. True symmetrical, differential amplifier circuits from input to output. Thick brushed Soft Shadow Silver faceplate with Satin Black middle plate.
  • Page 14 Notice to all Classé Product owners: Thank you for your purchase of a Classé Audio component. All of us at Classé have taken extreme care to ensure that your purchase will become a prized investment. We are proud to inform you that all Classé Audio components have been officially approved for the European Community CE mark.