Troubleshooting - Yamaha RX-V1600 Owner's Manual

TROUBLESHOOTING
Problem Cause Remedy
See
page
The sound suddenly The protection circuitry has been activated Check that the impedance selector setting is correct. 31
goes off. because of a short circuit, etc.
Check the speaker wires are not touching each other
-
and then tum this unit back on.
The sleep timer has turned the unit otf. Turn on the power. and play the source again. -
The sound is muted.
Press MUTE to cancel a mute. 38
Only the speaker on Incorrect cable connections. Connect the cables properly. If the problem persists,
20
one side can be
the cables may be defective.
heard.
Incorrect balance settings in the OSD Adjust the SP LEVEL settings.
80
menu.
Only the center When playing a monaural source with a
~
speaker outputs CINEMA DSP program, the source signal
substantial sound. is directed to the center channel, and the
front and surround speakers output etfect
sounds.
!----.-
No sound from the
The sound field programs are turned off. Press STRAIGHT (EFFECT) to turn them on.
42
effect speakers
You are using a source or program Try another sound field program.
combination that does not output sound 36
from all channels.
No sound from the The output level of the center speaker is Raise the level of the center speaker.
80
center speaker
set to minimum.
CENTER SP is set to NONE in Select the appropriate setting for the center speaker.
78
SPEAKER SET.
One of the HiFi DSP programs (except for Try another sound field program.
36
7ch Stereo) has been selected.
No sound from the The output level of the surround speakers Raise the output level of the surround speakers.
80
surround speakers is set to minimum.
SUR. LlR SP is set to NONE in Select the appropriate setting for the surround left and
78
SPEAKER SET. right speakers.
A monaural or stereo source is being Press STRAIGHT (EFFECT) to turn on the sound
-
played with STRAIGHT. fields.
No sound from the
Presence speakers are selected. Select SB in PRIORITY.
79
surround back
speakers
SUR. LlR SP is set to NONE in If the surround left and right speakers are set to
SPEAKER SET. NONE, surround back speakers are automatically set
78
to NONE. Select the appropriate setting for the
surround left and right speakers.
SB LlR SP is set to NONE in SPEAKER Select SMLxl, SMLx2, LRGxl or LRGx2.
79
SET.
No sound from the LFE/BASS OUT is set to FRONT when a
Select SWFR or BOTH.
subwoofer
Dolby Digital or DTS signal is being
78
played.
LFE/BASS OUT is set to SWFR or
Select BOTH.
FRONT when a 2-channel source is being
78
played.
The source does not contain low bass
----
-
signals.
~-
111
TROUBLESHOOTING
Problem Cause Remedy
See
page
The sound suddenly The protection circuitry has been activated Check that the impedance selector setting is correct. 31
goes off. because of a short circuit, etc.
Check the speaker wires are not touching each other
-
and then tum this unit back on.
The sleep timer has turned the unit otf. Turn on the power. and play the source again. -
The sound is muted.
Press MUTE to cancel a mute. 38
Only the speaker on Incorrect cable connections. Connect the cables properly. If the problem persists,
20
one side can be
the cables may be defective.
heard.
Incorrect balance settings in the OSD Adjust the SP LEVEL settings.
80
menu.
Only the center When playing a monaural source with a
~
speaker outputs CINEMA DSP program, the source signal
substantial sound. is directed to the center channel, and the
front and surround speakers output etfect
sounds.
!----.-
No sound from the
The sound field programs are turned off. Press STRAIGHT (EFFECT) to turn them on.
42
effect speakers
You are using a source or program Try another sound field program.
combination that does not output sound 36
from all channels.
No sound from the The output level of the center speaker is Raise the level of the center speaker.
80
center speaker
set to minimum.
CENTER SP is set to NONE in Select the appropriate setting for the center speaker.
78
SPEAKER SET.
One of the HiFi DSP programs (except for Try another sound field program.
36
7ch Stereo) has been selected.
No sound from the The output level of the surround speakers Raise the output level of the surround speakers.
80
surround speakers is set to minimum.
SUR. LlR SP is set to NONE in Select the appropriate setting for the surround left and
78
SPEAKER SET. right speakers.
A monaural or stereo source is being Press STRAIGHT (EFFECT) to turn on the sound
-
played with STRAIGHT. fields.
No sound from the
Presence speakers are selected. Select SB in PRIORITY.
79
surround back
speakers
SUR. LlR SP is set to NONE in If the surround left and right speakers are set to
SPEAKER SET. NONE, surround back speakers are automatically set
78
to NONE. Select the appropriate setting for the
surround left and right speakers.
SB LlR SP is set to NONE in SPEAKER Select SMLxl, SMLx2, LRGxl or LRGx2.
79
SET.
No sound from the LFE/BASS OUT is set to FRONT when a
Select SWFR or BOTH.
subwoofer
Dolby Digital or DTS signal is being
78
played.
LFE/BASS OUT is set to SWFR or
Select BOTH.
FRONT when a 2-channel source is being
78
played.
The source does not contain low bass
----
-
signals.
~-
111