Yamaha RX-V1600 Owner's Manual page 105

4
Press the buttons for the functions you want
to include in the macro operation in
sequence.
You can set up to 10 steps (10 functions). After you
have set 10 steps, FULL appears and the remote
control automatically exits the macro mode.
(U.S.A. model)
REMOTE CONTROL FEA TURES
You can clear all changes tnade in each function set, such
as learned functions, macros, renamed source names and
setup remote control codes.
• Basic CLEAR operations
1
Set AMP/SOURCErrV to AMP or SOURCE.
Press CLEAR by using a ballpoint pen or
similar object.
CLEAR appears in the display window.
MCR 2: AV POWER
MCR 3: AUDIO SEL
MCR 1: DVD
Indicates the
number of macro
steps entered
2
CiY
t
Flashes alternately so you can
set the next step
If you do not complete each of the following steps within 30
seconds, the clearing mode will be automatically canceled.
In this case, press CLEAR again.
3
Press
11/ \I
to select the clear mode.
To change the selected source component, press
SELECT
/1 / 'V.
Pressing the input selector buttons will
program a macro step, whereas SELECT
/1 / ' V
only changes
the selected component and corresponding component control
area.
5
Press MACRO again when the operation
sequence you want to program is complete.
ERROR appears in the display window if you press a button
not indicated in the respective step, or if you press more than
one button simultaneously.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost. However, the stored data will be lost
in case the power cord is disconnected from the AC
wall outlet for more than one week.
4
L;CD Clears all learned functions in the respective
component control area. Press an input selector
button to select the component.
L;AMP Clears all learned functions for this unit's control
area.
L;ALL Clears all learned functions.
M;ALL Clears all programmed macros.
RNAME Clears all renamed source names.
FCTRY Clears all remote functions and returns the remote
to the factory settings.
The name of a component is shown after a semicolon (;).
Press and hold CLEAR again for about 3
seconds.
WAIT appears in the display window. If clearing was
successful, C;OK appears in the display window.
,I,
~<i>~
Once you have cleared a learned function for a button, the
button reverts to the factory setting (or to the manufacturer
setting, if you have set remote control codes).
L;ALL and FCTRY may take about 30 seconds to complete.
101
4
Press the buttons for the functions you want
to include in the macro operation in
sequence.
You can set up to 10 steps (10 functions). After you
have set 10 steps, FULL appears and the remote
control automatically exits the macro mode.
(U.S.A. model)
REMOTE CONTROL FEA TURES
You can clear all changes tnade in each function set, such
as learned functions, macros, renamed source names and
setup remote control codes.
• Basic CLEAR operations
1
Set AMP/SOURCErrV to AMP or SOURCE.
Press CLEAR by using a ballpoint pen or
similar object.
CLEAR appears in the display window.
MCR 2: AV POWER
MCR 3: AUDIO SEL
MCR 1: DVD
Indicates the
number of macro
steps entered
2
CiY
t
Flashes alternately so you can
set the next step
If you do not complete each of the following steps within 30
seconds, the clearing mode will be automatically canceled.
In this case, press CLEAR again.
3
Press
11/ \I
to select the clear mode.
To change the selected source component, press
SELECT
/1 / 'V.
Pressing the input selector buttons will
program a macro step, whereas SELECT
/1 / ' V
only changes
the selected component and corresponding component control
area.
5
Press MACRO again when the operation
sequence you want to program is complete.
ERROR appears in the display window if you press a button
not indicated in the respective step, or if you press more than
one button simultaneously.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost. However, the stored data will be lost
in case the power cord is disconnected from the AC
wall outlet for more than one week.
4
L;CD Clears all learned functions in the respective
component control area. Press an input selector
button to select the component.
L;AMP Clears all learned functions for this unit's control
area.
L;ALL Clears all learned functions.
M;ALL Clears all programmed macros.
RNAME Clears all renamed source names.
FCTRY Clears all remote functions and returns the remote
to the factory settings.
The name of a component is shown after a semicolon (;).
Press and hold CLEAR again for about 3
seconds.
WAIT appears in the display window. If clearing was
successful, C;OK appears in the display window.
,I,
~<i>~
Once you have cleared a learned function for a button, the
button reverts to the factory setting (or to the manufacturer
setting, if you have set remote control codes).
L;ALL and FCTRY may take about 30 seconds to complete.
101