Advanced Operations - Yamaha RX-V1600 Owner's Manual

ADVANCED OPERATIONS
I
You can switch between the available OSD modes and manually adjust the output level of each speaker.
You can display the operating information of this unit on a
video monitor. If you display the SET MENU and sound
field program parameter settings on a monitor, it is much
easier to see the available options and parameters than it is
to read the information in the front panel display.
Turn on the video monitor connected to this unit
and then press ON SCREEN on the remote
control repeatedly to change the OSD mode.
The OSD mode changes in the following order:
Full display
~
Short display
~
Display off
ON SCREEN
~
Full display
Short display
You can manually adjust the output level of each speaker
while listening to a music source. This is also possible
when playing sources through the MULTI CH INPUT
jacks.
This operation will override the level adjustments made in AUTO
SETUP (see page 32) and SP LEVEL (see page 80).
1
2
3
(U.S.A. model)
Display off
Full display
Fully shows the sound field program parameter settings as
well as the contents of the front panel display.
Short display
Briefly shows the contents of the front panel display at the
bottom of the screen each time you operate this unit.
1
Set AMP/SOURCEfTV to AMP.
t:l1.151C
-:.- pOP.·",
F.: oc.k
D5P LEUEL····0dB
P. I
t·~
IT. DL
I..... .
2 1
r,' 1 ::;,
P.POOM 5IZE··1.0
5. I
t,~
IT. DL
1' 1 ' . • 3
1
r'l ::;,
5.POOM 5IZE··1.0
Display off
Only the operations performed using ON SCREEN on the
remote control are displayed. However, the OSD is
displayed when using SET MENU or the test tone feature
even if the OSD mode is turned off.
FRONT L adjusts the front left speaker level.
CENTER adjusts the center speaker level.
FRONT R adjusts the front right speaker level.
SUR.R adjusts the surround right speaker level.
S8 R adjusts the surround back right speaker level.
S8 L adjusts the surround back left speaker level.
SUR.L adjusts the surround left speaker level.
SWFR adjusts the subwoofer level.
PRNS L adjusts the presence left speaker level.
PRNS R adjusts the presence right speaker level.
LEVEL
~
BAND
~
2
Press LEVEL repeatedly to select the
speaker you want to adjust.
3
Press
<:J
I
[>
to adjust the speaker output
level.
Control range:
+
10 dB to -10 dB
t'1U51 C
POF·.····Pock
Short display Full display
• The OSD signal is not output at the OUT (REC) jack and will
not be recorded.
• You can display a gray background in the OSD when there is no
video signal being input by setting GRAY BACK to AUTO
(see page 85).
• The OSD is not displayed in the following cases:
- When video signals in the progressive fonnat or HDTV video
signals are being input.
- When the signals input at the HDMI IN 1 or HDMI IN 2 jack
are being output at the HDMI OUT jack.
- When V CONY. is set to OFF (see page 85).
89
ADVANCED OPERATIONS
I
You can switch between the available OSD modes and manually adjust the output level of each speaker.
You can display the operating information of this unit on a
video monitor. If you display the SET MENU and sound
field program parameter settings on a monitor, it is much
easier to see the available options and parameters than it is
to read the information in the front panel display.
Turn on the video monitor connected to this unit
and then press ON SCREEN on the remote
control repeatedly to change the OSD mode.
The OSD mode changes in the following order:
Full display
~
Short display
~
Display off
ON SCREEN
~
Full display
Short display
You can manually adjust the output level of each speaker
while listening to a music source. This is also possible
when playing sources through the MULTI CH INPUT
jacks.
This operation will override the level adjustments made in AUTO
SETUP (see page 32) and SP LEVEL (see page 80).
1
2
3
(U.S.A. model)
Display off
Full display
Fully shows the sound field program parameter settings as
well as the contents of the front panel display.
Short display
Briefly shows the contents of the front panel display at the
bottom of the screen each time you operate this unit.
1
Set AMP/SOURCEfTV to AMP.
t:l1.151C
-:.- pOP.·",
F.: oc.k
D5P LEUEL····0dB
P. I
t·~
IT. DL
I..... .
2 1
r,' 1 ::;,
P.POOM 5IZE··1.0
5. I
t,~
IT. DL
1' 1 ' . • 3
1
r'l ::;,
5.POOM 5IZE··1.0
Display off
Only the operations performed using ON SCREEN on the
remote control are displayed. However, the OSD is
displayed when using SET MENU or the test tone feature
even if the OSD mode is turned off.
FRONT L adjusts the front left speaker level.
CENTER adjusts the center speaker level.
FRONT R adjusts the front right speaker level.
SUR.R adjusts the surround right speaker level.
S8 R adjusts the surround back right speaker level.
S8 L adjusts the surround back left speaker level.
SUR.L adjusts the surround left speaker level.
SWFR adjusts the subwoofer level.
PRNS L adjusts the presence left speaker level.
PRNS R adjusts the presence right speaker level.
LEVEL
~
BAND
~
2
Press LEVEL repeatedly to select the
speaker you want to adjust.
3
Press
<:J
I
[>
to adjust the speaker output
level.
Control range:
+
10 dB to -10 dB
t'1U51 C
POF·.····Pock
Short display Full display
• The OSD signal is not output at the OUT (REC) jack and will
not be recorded.
• You can display a gray background in the OSD when there is no
video signal being input by setting GRAY BACK to AUTO
(see page 85).
• The OSD is not displayed in the following cases:
- When video signals in the progressive fonnat or HDTV video
signals are being input.
- When the signals input at the HDMI IN 1 or HDMI IN 2 jack
are being output at the HDMI OUT jack.
- When V CONY. is set to OFF (see page 85).
89