Programming System Features; Bitwriter Only Options; Remote Control Learn Routine; Long Term Event History - Viper 3105V Owner's Manual

Programming System Features

The System Features Learn Routine dictates how the unit operates. It is possible to ac-
cess and change most of the feature settings using the Valet switch/Control button.*
*Depending on which model is installed, the system uses either an external Valet
switch and an external Status LED or a Control Center with an onboard Control but-
ton (Valet Switch) and Status LED.
1. Open a door.
Turn the ignition on, then off.
2.
Select a Menu. Press and hold the Valet switch/Control button. The number
3.
of siren chirps indicates the menu number. 1 chirp indicates menu 1, 2 chirps
- menu 2.
4. When the desired menu chirps are heard, release the Valet switch/Control
button.
5. Select a Feature. Press and release the Valet switch/Control button the
number of times corresponding to the feature you wish to change. Then press
and hold one more time to select the features.
6. Program the Feature. While holding the Valet switch/Control button, you can
program the feature using the remote control.
To change the desired options press; = one chirp setting, while
chirps setting.
Once a feature is programmed:
Other features can be programmed within the same menu
Another menu can be selected
The learn routine can be exited if programming is complete
To access another feature in the same menu:
1. Press and release the Valet switch/Control button the number of times neces-
sary to advance from the feature you just programmed to the next one you
want to program.
Then press the Valet switch/Control button once more and hold it.
2.
To select another menu:
1. Press and hold the Valet switch/Control button.
2. After 3 seconds, the unit advances to the next menu and the siren chirps, indi-
cating which menu has been accessed.
The learn routine exits if any of the following occurs:
The open door is closed
The ignition is turned On
There is no activity for 20 seconds
The Valet switch/Control button is pressed too many times
Bitwriter - Only Options
If programming with the Bitwriter®, the learn routine can be locked or un-
locked. If the learn routine has previously been locked, it must be unlocked
with Bitwriter® - this cannot be done manually with the Control button.
The Bitwriter® gives you access to a wider range of system options. These
features and the adjustments that may be programmed are described in the table
below. Default settings are in bold type.
Menu Feature Default Option 2
Item
1 Ignition Controlled Ignition Controlled Ignition Controlled
Lock Lock ON Lock OFF
Ignition Controlled
2 Ignition Controlled Ignition Controlled
Unlock Unlock ON Unlock OFF
3 Siren Duration 30 second siren 1-180 seconds (in 1
duration second increments)
© 2012 Directed. All rights Reserved.
Feature Menus
Default factory settings are in bold type.
Menu 1: Basic Features
Feature 1- chirp setting 2- chirp setting
#
1-1 Active arming Passive arming
1-2 Chirps ON Chirps OFF
Ignition controlled door locks
1-3 Ignition controlled door locks OFF
ON
1-4 Active locking only Passive locking
1-5 Panic w/ignition ON No Panic w/ignition ON
1-6 0.8 second door lock pulses 3.5 second door lock pulses
1-7 Forced passive arming ON Forced passive arming OFF
= two
1-8 Automatic Engine Disable ON Automatic Engine Disable OFF
Armed When Driving (AWD)
1-9 Vehicle Recovery System (VRS)
1-10 Code Hopping™ ON Code Hopping OFF
Menu 2: Advanced Features
Feature 1- chirp setting 2- chirp setting
#
2-1 Siren Horn Honk
2-2 30 second siren duration 60 second siren duration
NPC® ON
2-3 NPC OFF
2-4 Progressive door trigger Instant door trigger
2-5 Valet switch/Control button Valet switch/Control button input
input: 1 pulse 2-5 pulses
2-6 Door trigger error chirp ON
Door trigger error chirp OFF
2-7 Ignition controlled domelight Ignition controlled domelight OFF
ON
2-8 Single unlock pulse Double unlock pulse
2-9 Single lock pulse Double lock pulse
2-10 Channel 3: Validity Channel 3: latched/
latched reset with ignition/
30- second timed/
second unlock output*
2-11 Comfort Closure (ON, 20 sec) Comfort Closure (OFF)
*Second unlock available only if feature 2-8 is programmed to single
pulse.

Remote control learn routine

The system comes with two remote controls that have been taught to the control
module. The control module can store up to four different remote control codes in
memory. The button configurations can be changed on the remote control, follow
the procedure below and use the table to configure it for an associated function.
If the system was previously programmed using the 998T Bitwriter, the learn routine
may be locked. If the siren generates one long chirp when attempting to program
the unit, the learn routine is locked and must be unlocked using the 998T Bitwriter
before proceeding.
1. Open a door. The 12 pin harness GREEN wire or the 12 pin harness VIOLET
wire must be connected.
2. Turn the ignition on. The 12 pin harness YELLOW wire must be connected.
3. Select a channel. Press and release the Valet switch/Control button the number
of times necessary to access the channel you want, and then press and hold
the Valet switch/Control button once more. The siren chirps and the LED blinks
the number of times corresponding to the channel accessed.
4. While holding the Valet switch/Control button, press the button on the remote
control you want to assign to the selected channel. The unit chirps indicating
successful programming.
Note: It is not possible to teach a remote control button to the system more
than once.
Note: When programming channels 1- 6, a button must be taught to the unit in
Channel 1 or Channel 5 before programming remaining channels.
Channels 2, 5, 6: Use Channels 2, 5, and 6 to assign the arm, disarm and panic
functions to buttons on the remote control. Teaching a button to Channel 5 or Chan-
nel 1 erases some memory information, and auxiliary functions may have to be
reprogrammed.
Channel/ Function
Channel # Function
1 Arm/Disarm
2 Panic Only
3 Silent mode, Remote Valet,
Trunk Release
4 Remote starter or other accessories
5 Arm Only
6 Disarm Only
7 Auto learn standard 4- button configuration*
8 Auto learn 3- button configuration*
9 Delete all transmitters**
* For auto learn configurations, see Remote control (transmitter) configurations
section of this guide.
** The delete all transmitters option also resets the programmed settings to their
default factory state.
The learn routine exits if any of the following occurs:
The open door is closed
The ignition is turned off
There is no activity for 15 seconds
The Valet switch/Control button is pressed too many times

Long Term Event History

The system stores the last two full triggers in memory. These are not erasable. Each
time the unit sees a full trigger, the older of the two triggers in memory is replaced by
the new trigger. To access long term event history:
1. With the ignition Off, press and hold the Valet switch/Control button.
2. Turn the ignition On.
3. Release the Valet switch/Control button.
Within 5 seconds, press and release the Valet switch/Control button. The
4.
status LED flashes in groups indicating the last two zones that triggered the unit
for 1 minute or until the ignition is turned off. Refer to table of zones.
Note: The Warn Away triggers are not stored to memory and is not reported.
Table of Zones
A zone is represented by the number of status LED flashes used by the
system to identify a particular type of input.
Zone Description Input Description
1 Optional trigger input 12 pin harness Blue wire
2 Instant trigger: a heavier impact Onboard Shock Sensor.
detected by the shock sensor
3 Door switch trigger 12 pin harness Green or Violet wire
4 Instant trigger: For optional sensors Optional Sensor Port
5 Ignition trigger 12 pin harness Yellow wire
QRN3305 2012-09
2