Advertisement
When the food temperature is within 10°F of the set temperature (e.g. 160°F), the main unit will beep
twice and voice prompt; " Your food is almost ready". The unit will repeat the above two beeps and the
voice after 4 seconds silence.
When the food temperature reaches the target temperature, the main unit will beep 3 times and voice
prompt: "Your food is ready".
The unit will repeat the beeps and phrase for 1 minute. The alert icon will also blink during this time.
The user can press STOP button to stop the alert early.
Displayed food temperature range
: -10°C to +210°C (+14°F to +410°F)
Displayed temperature resolution
: 1°C (2°F)
Description of Buttons on Receiver
1. [HR/ ]
In timer mode, press once to increase the hour setting. Press and hold 2 seconds to fast increase the
hour by 10. In thermometer mode, press once to increase the temperature value. Press and hold 2
seconds to fast increase the temperature value by 10.
2. [CLEAR/°F/°C]
When the timer count down or count up process is stopped, press to clear the timer reading. In
thermometer mode, press to select temperature readings in Celsius or Fahrenheit.
3. [MIN/ ]
In timer mode, press once to increase the minute setting. Press and hold 2 seconds to fast
increase the minute by 10. In thermometer mode, press once to decrease the temperature value.
Press and hold 2 seconds to fast decrease the temperature value by 10.
4. [MODE]
Press to select thermometer or timer mode. Press & hold for 2 seconds to register with the
transmitter.
5. [MEAT]
In thermometer mode, press to select meat type, BEEF, VEAL, LAMB, PORK,
CHICK (chicken) or TURKY (turkey).
6. [TASTE]
In thermometer mode, select the taste level, W.DONE (well done), MEDIUM,
M. RARE (medium rare) or RARE.
7. [START/STOP]
Press to start or stop the timer countdown or count up.
8. [ON/OFF]
On normal operation with full function. Off turns receiver off.
9. [LIGHT]
Press to activate the backlight for 10 seconds.
10. [RESET]
Reset to restore it to factory setting.
Description of Buttons on Transmitter
1. TX – transmit manually, terminates the auto registration process. Press and hold for 2 seconds to
register the radio frequency with the receiver.
2. ON/OFF – on normal operation with full function. Off turns transmitter off.
HELPFUL HINTS
If the receiver and/or the transmitter display LLL or HHH instead of the probe temperature, wait for
probe to reach room temperature. If LLL or HHH is still displayed it is likely the internal probe wire has
shorted out either through moisture or heat damage.
Do not immerse the probe in water while cleaning.
Do not allow the probe or probe wire to come into contact with flames. If cooking with grill cover
closed, only use medium or low heat.
Make sure the probe tip is inserted into the meat at least 1 inch.
If the temperature displayed seems to read too high or the temperature seems to increase too quickly,
check to make sure the probe tip is not poking through the food to outside. Reposition the probe tip in
the center of the thickest part of food. Avoid touching bone or heavy fat areas.
Cautions:
Always wear a heat resistant glove to touch the stainless steel probe sensor or wire during or just after
cooking. Do not touch with bare hands.
Keep the stainless steel probe sensor and wire away from children.
Clean the stainless steel probe and dry thoroughly after each and every use.
3
Do not use the receiver in the rain, It is not waterproof.
Do not expose the plug of the stainless steel probe or the plug in hole of the transmitter to water or any
liquid. This will result in a bad connection and faulty readings.
Do not expose the receiver or transmitter to direct heat or surface.
Do not use stainless steel probe in microwave oven.
The Remote Thermometer registers temperatures as low as 14
o
will be displayed below 14
F and HHH will be displayed above 410
o
sensor above 410
F. Doing so will deteriorate the wire.
Cleaning
Always wear a heat resistant glove to touch the stainless steel probe sensor or wire during or just after
cooking. Do not touch with bare hands.
Keep the stainless steel probe sensor and wire away from children.
Wash the metal probe tip with hot soapy water and dry thoroughly. Do not immerse the probe in water
while cleaning.
Wipe the transmitter and receiver with damp cloth. Do not immerse either in water.
Information to user
"Modifications not authorized by the manufacturer may void users authority to operate this device"
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
LIMITED NINETY DAY WARRANTY
Maverick Industries Inc. warrants the Redi Chek
workmanship for a period of 90 days, from date of purchase. Should any repairs or servicing under this
warranty be required, contact Maverick Customer Service by mail or phone for instructions on how to
pack and ship the Redi Chek
®
Remote to Maverick's National Service Center located as follows:
Maverick Customer Service
94 Mayfield Ave
Edison NJ 08837
Telephone: (732) 417-9666
Hours: Weekdays 8:30 AM- 4:30 PM
Do not send any parts or product to Maverick without calling and obtaining a Return Authorization
Number and instructions.
This warranty is VOID if instructions for use are not followed; for accidental damage; for commercial
use; for damage incurred while in transit; or if the Redi Chek
This warranty gives you specific legal rights and you may also have other rights which vary from state
to state.
Replacement probes
To purchase, out of warranty, stainless steel replacement probes please mail us a check to address below
and specify probe type:
ET-901B Probe
$12.00/ea
All prices include shipping & handling. NJ residents add 6% sales tax.
Attn Customer Service
Maverick Industries, Inc.
94 Mayfield Ave.
Edison NJ 08837
www.maverickhousewares.com
o
F(-10
o
C) and as high 410
o
F(210
o
F. Do not use the stainless steel probe
®
Remote to be free of defects in parts, materials and
®
Remote has been tampered with.
o
C). LLL
4
Advertisement
