Related Manuals for Partner 350
Summary of Contents for Partner 350
- Page 1 INSTRUCTION MANUAL IMPORTANT INFORMATION: Please read these instructions carefully and make sure you understand them before using this unit. Retain these instructions for future reference. 545123594 Rev. 2 1/31/07 BRW...
- Page 2 IDENTIFICATION (WHAT IS WHAT?) Front Hand Guard Front Handle Chain Adjustment Tool Starter Rope (Bar Tool) ON/STOP Switch Muffler Chain Primer Bulb Starter Bar Oil Fill Cap Housing Fuel Mix Fill Cap Cylinder Cover Throttle Chain Lockout Direction Adjusting Rear of Travel Screw Handle...
- Page 3 IDENTIFICATION OF SYMBOLS Starting Reminder Move ON/STOP switch to Pull the starter rope the ON position. sharply 5 times with your right hand. Push the choke/fast idle Slowly press primer bulb lever in to the HALF 6 times. CHOKE position. Pull choke/fast idle lever Pull the starter rope sharply out to the full extent (to...
- Page 4 S Do not operate a chain saw that is dam- S Rotational Kickback can occur when the aged, improperly adjusted, or not com- moving chain contacts an object at the up- pletely and securely assembled. Always per tip of the guide bar. This contact can replace bar, chain, hand guard, or chain cause the chain to dig into the object, brake immediately if it becomes damaged,...
- Page 5 manufacturer’s chain sharpening and main- S Do not overreach. You could be drawn or tenance instructions. Check tension at regu- thrown off balance and lose control of the lar intervals with the engine stopped, never saw. with the engine running. Make sure the bar S Do not cut above shoulder height.
- Page 6 and low- -kickback saw chains reduce the equipped with a chain brake that is designed chance and magnitude of kickback and are to stop the chain immediately if you get a recommended. Your saw has a low kick- kickback. The chain brake reduces the risk back chain and bar as original equipment.
- Page 7 DISENGAGED Front Hand Guard Mount the Bar ENGAGED 6. Carefully remove the chain from the pack- age. Hold chain with the drive links as shown. Chain Brake Tip of 11. Now, install chain brake making sure the adjusting pin is positioned in the lower hole in the guide bar.
- Page 8 Lift up the tip of the bar and securely tighten the chain brake nuts with the bar Adjusting tool. Screw Recheck chain tension. Chain Brake Nuts Guide Bar Chain Brake Nuts Adjusting Screw - - 1/4 Turn WARNING : If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury.
- Page 9 For cold weather starting, start the unit at procedure listed above. Ensure the ON/ FULL CHOKE; allow the engine to warm up STOP switch is in the ON position. before squeezing the throttle trigger. Starting could require pulling the starter rope handle many times depending on how badly NOTE : Do not attempt to cut material with...
- Page 10 CUTTING METHODS IMPORTANT POINTS Plan a clear retreat path S Cut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc. S Stop the saw if the chain strikes a foreign object. Inspect the saw and repair parts as necessary.
- Page 11 S Be alert to signs that the tree is ready to fall: WARNING cracking sounds, widening of the felling cut, : Never turn saw upside or movement in the upper branches. down to undercut. The saw cannot be con- S As tree starts to fall, stop saw, put it down, trolled in this position.
- Page 12 LIMBING AND PRUNING S Remove larger, supporting branches with the cutting techniques described in BUCK- WARNING ING WITHOUT A SUPPORT. : Never climb into a tree to S Always use an overcut to cut small and limb or prune. Do not stand on ladders, plat- freely hanging limbs.
- Page 13 Replace guide bar when the groove is worn, WARNING the guide bar is bent or cracked, or when : Disconnect the spark excess heating or burring of the rails occurs. plug before performing maintenance, ser- If replacement is necessary, use only the guide vice or adjustments, except for carburetor bar specified for your saw in the repair parts list adjustments.
- Page 14 TROUBLESHOOTING TABLE WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit. TROUBLE CAUSE REMEDY Engine will not 1. Move ignition switch to ON. 1. Ignition switch off. start or will run 2.
- Page 15 TECHNICAL DATA SHEET ODEL: Partner 350 ENGINE Cylinder volume, cm Stroke, mm Idle speed, rpm 3,000 Recommended max speed, unloaded, rpm 13,000 Power, kW IGNITION SYSTEM Manufacturer Walbro Type of ignition system Spark plug Champion Electrode gap, mm FUEL AND LUBRICATION SYSTEM...
- Page 16 Husqvarna Outdoor Products Italia S.p.A. Via Como 72 Valmadrera, Lecco ITALY I- -23868...