Page 1
4000. Manual del operador Lea cuidadosamente estas instrucciones y asegúrese de que las comprende bien antes de usar el 4000. Manuel d’utilisation Veuillez lire attentivement ces instructions et assurez-vous de bien les comprendre avant d’utiliser la machine modèle 4000.
Remove the saw from the container using proper lift- ing techniques. Discard or recycle the packing material per your regional laws. In your container will be the 4000 saw, blade shaft wrench, spark plug wrench, an owner’s manual, an engine owner’s manual, a part list, a warranty card, a joint...
The 4000 is designed as a heavy duty commercial, industrial, and paving Ultra Early Entry con- crete saw. The patented Soff-Cut Ultra Early Entry dry cutting system controls random cracking of concrete through the early timing of the saw cutting usually within one to two hours after finishing process is com- pleted.
MODEL No: ________________ ENGINE MODEL: _____________ ENGINE TYPE: ______________ The 4000 model and serial number as well as the engine model number, engine type and code are critical in order to obtain the correct service parts. In this manual a Safety Alert Symbol identify safety information about hazards which can result in death, serious injury and/or property damage.
The blade should fit snugly on clean, undamaged, tri-arbor shaft. • Use only Husqvarna Excel Series blades or blades marked with a maximum operating speed greater than 3500 rpm. • Never operate the saw without the blade block assembly securely in place including blade cover, lexan shields and skid plate installed in working order.
Remove the blade block cover (A) by turning the two locking knobs counter-clockwise. Insert the blade wrench supplied with the saw on the blade shaft bolt (C) on the end of the blade shaft in the blade block (I). Rotate the blade shaft counter-...
G. Oil dipstick H. Battery box Oil drain hose Fuel tank Fuel cap Hour meter/Tachometer M. Saw forward speed lever N. Guide arm lever O. Engine throttle control Blade depth switch Q. Transmission oil fill cap R. Cut depth pointer...
OPERATING INSTRUCTIONS Handle bar Blade block Experience is very important when running the 4000 saw. A skilled worker is highly recommended. Always do an inspection of the saw before starting the engine. Check the fuel (J) and oil level (G) per the enclosed engine manual. SAE 10W/30 oil and unleaded gasoline with an 87 or higher octane should be used.
Always place containers on the ground away from your vehicle when filling. - Remove the 4000 from the truck or trailer and refuel it on the ground. If this is not possible, then refuel the equipment with a portable container, rather than from a gasoline dispenser nozzle.
Change oil after the first 5 to 8 hours of use. Thereafter every 50 hours. The oil drain hose (D) is located at the front of the saw. 1. With the engine OFF but still warm, remove the brass cap and drain the oil in a pan and remove the oil filter (C).
Check blade drive belt, the transmission drive belt and belt tensioner. Replace the fuel filter. Do not modify the saw! Use only Husqvarna Construc- tion Products replacement parts. Use of unauthorized parts may create a danger or damage the engine.
Cut is being specified more today than ever, sometimes the ultra early-entry spec is not always followed on the job site. In order for the Soff-Cut system and an experienced Husqvarna contractor to do a satisfactory job, four components must exist to meet the “specification”:...
- Insure the slab is in clean with no debris that could raise the skid plate or saw while cutting. - Use Husqvarna joint protectors at all cut intersections. - Clean excess concrete debris from the blade block assembly. - Check that the scrapers in the blade block are not bent or binding.
TECHNICAL SPECIFICATIONS Weight and Dimensions 4000 Weight – dry Weight with gasoline and oil full Length Width Height Blade Material cut Blade type Blade rotation Blade shaft speed Cutting depth Cutting distance from wall Average cutting rate - Estimate only. Speed will vary with job conditions and concrete mixes.
HUSQVARNA EQUIPMENT WARRANTY New 4000 sold by Husqvarna Construction Products are warranted to be free from manufacturing defects in nor- mal service for a period of six (6) months for labor and up to one (1) year on parts from date of purchase by the original consumer purchaser or date of introduction into rental company fleet.