Husqvarna Soff-Cut 2000 Operator's Manual
Hide thumbs
Also See for Soff-Cut 2000:
- Operator's manual (47 pages) ,
- Operator's manual (148 pages) ,
- Operator's manual (104 pages)
Related Manuals for Husqvarna Soff-Cut 2000
Summary of Contents for Husqvarna Soff-Cut 2000
- Page 1 US Operator’s manual Soff-Cut 2000 Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. HUSQVARNA CONSTRUCTION PRODUCTS...
-
Page 2: Table Of Contents
NOTE: No diamond cutting blade or skid plate is included Excel series blades ........with the saw. Purchase the appropriate Husqvarna Excel Blade and skid plate installation ....Series 9 or 10 inch blade from your local Husqvarna Con- struction Product dealer. What is what? ..........TRANSPORTING Operating instructions ....... -
Page 3: I Ntroduction, Personal Safety
The patented low noise and low dust blade block and skid plate technology in conjunction with the Husqvarna blades allows for Ultra Early Entry sawing the same day while minimizing chipping and spalling. The saw is a self-propelled style with manual controls for most functions. -
Page 4: Registration Of The Product
REGISTER THE PRODUCT Please register your new 2000 with Husqvarna Construction Products by mailing in the registration card that came with the machine or you can register on the internet site www.husqvarnawarranty.com Registration will allow us to contact in case of any critical updates or recalls on this machine. -
Page 5: Safety Warnings
• Do not operate the saw in areas of combustible material or fumes. Sparks may occur from the saw that could cause a • Use only Husqvarna Excel Series blades or blades marked fire or explosion. with a maximum operating speed greater than 3200 rpm. -
Page 6: Excel Series Blades
EXCEL SERIES BLADES The Excel Series of diamond blades have been designed specifically for the Soff-Cut Ultra Early Entry dry cutting system of green concrete. These specialty blades are designed to increase speed and life while cutting a wide range of aggregates. Choose the correct specification of diamond blade for your area as follows: Purple Excel Series 1000 XL10-1000... -
Page 7: What Is What
WHAT IS WHAT Model number and serial number What is what? Oil fill & dipstick Air cleaner C. Recoil starter D. Fuel shut off lever Choke lever Oil drain hose G. Fuel cap H. Fuel tank Transmission oil fill cap Hour meter/Tachometer Battery box Saw forward speed lever... -
Page 8: Operating Instructions
OPERATING INSTRUCTIONS Handle bar WARNING Blade release lever ASPHYXIATION HAZARD Engine on/off switch Running an engine in a confined or badly ventilated area can result in injury or death due to asphyxiation or carbon monoxide poisoning. Open the engine throttle lever to full open position for maxi- mum engine speed by pulling the throttle knob (Q) at the han- dle. -
Page 9: Fuel And Fuel Safety Warnings
FUEL HANDLING OIL HANDLING NOTICE WARNING Used oil is a hazardous waste product. Dispose Taking the following precautions will lessen the risk of used oil properly. Do not discard with household of injury and property damage: waste. Check with your local authorities, service center, or dealer for safe disposal/recycling facility. -
Page 10: Engine And Transmission Maintenance
ENGINE AND TRANSMISSION MAINTENANCE Engine Oil ADDITIONAL ENGINE INFORMATION Checking, Adding and Changing Oil Please see the Robin Operator’s Manual for additional infor- Check the engine oil level (B) daily with saw fully lowered and mation about servicing the engine. the engine level. -
Page 11: Other Maintenance
Skid plate Inspect the skid plate daily for damage, excessive wear in the Do not modify the saw! Use only Husqvarna Construc- blade slot, burrs on the concrete surface side, twisting and free tion Products replacement parts. Use of unauthorized movement up and down when installed on the blade block. -
Page 12: Sawing Contraction Joints
Husqvarna sawed contraction joints should be a minimum of 1/8th the concrete depth and a minimum of 1”... -
Page 13: Maximizing The Soff-Cut System
Cut is being specified more today than ever, sometimes the ultra early-entry spec is not always followed on the job site. In order for the Soff-Cut system and an experienced Husqvarna contractor to do a satisfactory job, four components must exist to meet the “specification”:... -
Page 14: Troubleshooting
- Use Husqvarna joint protectors at all cut intersections. - Insure that all wheels rolls freely and smoothly. - Clean excess concrete debris from the blade block assembly. -
Page 15: Technical Specifications
EC DECLARATION OF CONFORMITY Husqvarna AB, SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the Husqvarna Soff-Cut 2000 dating from 2010 serial numbers and onwards (the year is clearly stated on the rating plate, followed by the serial number), complies with the requirements of the COUNCILíS DIRECTIVE:... -
Page 16: Warranty
The use of any other blade except Husqvarna Construction Products blades and skid plates will void the warranty and could cause internal damage to the motor. - Page 17 www.husqvarnacp.com 1153477-95 Original instructions 2009-12-29 ´®z+UOo¶5N¨ ´®z+UOo¶5N¨...
Need help?
Do you have a question about the Soff-Cut 2000 and is the answer not in the manual?
Questions and answers