Husqvarna SOFF-CUT 150 Operator's Manual
Husqvarna motorcycle user manual
Hide thumbs
Also See for SOFF-CUT 150:
- Operator's manual (132 pages) ,
- Price list (48 pages) ,
- Operator's manual (88 pages)
Related Manuals for Husqvarna SOFF-CUT 150
Summary of Contents for Husqvarna SOFF-CUT 150
- Page 1 GB Operator’s manual Soff-Cut 150 Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. HUSQVARNA CONSTRUCTION PRODUCTS...
-
Page 2: Table Of Contents
NOTE: No diamond cutting blade or skid is included with the saw. Purchase the appropriate Excel Series 6 inch blade and skid plate from your local Husqvarna Construc- tion Product dealer. TRANSPORTING The 150 saw weights approximately 91 pounds (41 kilograms) when ready to use . -
Page 3: I Ntroduction, Personal Safety
If you have further questions you can contact the closest Husqvarna Construction Products location by writing or calling, see information below. You can also find the closest location by searching the internet at;... -
Page 4: Registration Of The Product
REGISTER THE PRODUCT Please register your new 150 with Husqvarna Construction Products by mailing in the registration card that came with the machine or you can register on the internet site Registration will allow us to contact in case of any critical updates or recalls on this machine. -
Page 5: Safety Warnings
The blade should fit snugly on clean, undamaged, tri-arbor shaft. • Use only Husqvarna Excel Series blades or blades marked with a maximum operating speed greater than 4450 rpm. • Never operate the saw without the blade block assembly securely in place including blade cover, lexan shields and skid plate installed in working order. -
Page 6: Excel Series Blades
EXCEL SERIES BLADES The Excel Series of diamond blades have been designed specifically for the Soff-Cut Ultra Early Entry dry cutting system of green concrete. These specialty blades are designed to increase speed and life while cutting a wide range of aggregates. Choose the correct specification of diamond blade for your area as follows: Purple Excel Series 1000 Green Excel Series 2000... -
Page 7: What Is What
Model number and serial number What is what? Oil dipstick or fill Oil drain C. Fuel shut off lever D. Choke lever Throttle lever Starter rope G. Air cleaner H. Fuel tank Engine on/off switch WHAT IS WHAT... -
Page 8: Operating Instructions
OPERATING INSTRUCTIONS Blade release lever Handle locking pin Blade block Front guide Experience is very important when running the 150 saw. A skilled worker is highly recommended. Always do an inspec- tion of the saw before starting the engine. Check the fuel (H) and oil level (A) per the enclosed engine manual. -
Page 9: Fuel And Fuel Safety Warnings
FUEL HANDLING WARNING Taking the following precautions will lessen the risk of injury and property damage: - Use extreme care in handling gasoline. It is extremely flammable and the vapors are explosive. - Extinguish all cigarettes, cigars, pipes, and other sources of ignition. -
Page 10: Maintenance
Replace air cleaner. Replace engine oil. Grease blade shaft bearings. Check blade drive belt. Do not modify the saw! Use only Husqvarna Construc- tion Products replacement parts. Use of unauthorized parts may create a danger or damage the engine. Daily... -
Page 11: Sawing Contraction Joints
Husqvarna sawed contraction joints should be a minimum of 1/8th the concrete depth and a minimum of 1”... -
Page 12: Maximizing The Soff-Cut System
Cut is being specified more today than ever, sometimes the ultra early-entry spec is not always followed on the job site. In order for the Soff-Cut system and an experienced Husqvarna contractor to do a satisfactory job, four components must exist to meet the “specification”:... -
Page 13: Troubleshooting
- Insure the slab is in clean with no debris that could raise the skid plate or saw while cutting. - Use Husqvarna joint protectors at all cut intersections. - Clean excess concrete debris from the blade block assembly. - Check that the scrapers in the blade block are not bent or binding. -
Page 14: Technical Specifications
EC DECLARATION OF CONFORMITY Husqvarna AB, SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the Husqvarna Soff-Cut 150 dating from 2010 serial numbers and onwards (the year is clearly stated on the rating plate, followed by the serial number), complies with the requirements of the COUNCILíS DIRECTIVE:... -
Page 15: Warranty
The use of any other blade except Husqvarna Construction Products blades and skid plates will void the warranty and could cause internal damage to the motor. - Page 16 www.husqvarnacp.com 1153478-26 ´®z+UOr¶6h¨ ´®z+UOr¶6h¨ Original instructions 2009-12-29...