Toshiba MCY-MAP0401HT Owner's Manual page 13

◆ To stop swinging
1
SWING/FIX
Push the button at the desired
position while the louver is swinging.
SWING/FIX
• Push the button repeatedly to change
the louver position again.
SWING/FIX
* However, even if the button is pushed
while the louver is swinging, one of the
indications below may sometimes be displayed
and may not set the louver to the highest
position.
▼ Indications when swinging is stopped
FAN / HEAT COOL / DRY
SWING/FIX
In this case, push the button again after 2
seconds.
• In COOL / DRY operation, the louver does not
stop as it directs downward. If stopping the
louver as it directs downward during swing
operation, it stops after moving to the third
position from the highest position.
▼ Indications when swinging is stopped
FAN / HEAT COOL / DRY
operation operation
◆ Unit select
• When two or more indoor units are controlled with
one remote controller, the louver direction can be set
for each indoor unit by selecting them individually.
• To set louver direction individually, push the
button (left side of the button) to display an indoor
unit number in the control group. Then set the louver
direction of the displayed indoor unit.
• When no indoor unit number is displayed, all indoor
units in the control group can be controlled
simultaneously.
UNIT LOUVER
• Each time you push the (left side of the
button), the indication changes as follows:
No Unit No. Unit No.
display 1-1 1-2
Unit No. Unit No.
1-4 1-3
23-EN
4-way cassette type only
◆ To set the louvers individually
1
UNIT LOUVER
Push the button (left side of the
button) during running to select a unit.
The unit number changes each time you push the
button.
Unit No. Unit No.
1-1 1-2
No Unit No.
display 1-4
• When no unit number is displayed, all units are
selected.
2
UNIT LOUVER
Push the button (right side of the
button) to select a louver.
Each time you push the button, the indicator on the
left of the remote controller changes as follows:
* When no louver number is displayed, all 4
louvers are selected.
Louver No.
Electrical control box
03
UNIT LOUVER
Refrigerant
pipe
04
Drain pipe
01
3
SWING/FIX
Push the
direction of the selected louver.
Each time you push the button, the indication
changes as follows:
(1)
(7)
Unit No.
1-3
* When cooling or drying, (4) and (5) are not
displayed.
◆ Setting the swing pattern
1
Push and hold the
seconds while the operation is stopped.
blinks.
2
No
UNIT LOUVER
Push the
display
to select a unit.
The unit number changes each time you push the
button.
Unit No.
1-1
No
display
The fan of the selected unit runs, and the louver
swings.
3
Push the
type.
02
Swing code
0001
0002
0003
REQUIREMENT
Do not set "0000".
(The louver may be damaged.)
– 12 –
4
button to confirm the Push the
5
Push the
▼ Standard swing
All four louvers swing simultaneously at the same
(2) (3) (4)
angle.
(6) (5)
SWING/FIX
FIX for at least 4
▼ Dual swing (Recommended for heating)
• Adjoining louvers alternately point horizontally and
button (left side of the button)
downward to heat the room evenly.
• Air blown downward reaches the floor, and air blown
horizontally is spread to circulate heat.
Unit No. Unit No.
1-2 1-3
Unit No. Horizontal
1-4
Downward
buttons to select a swing
Horizontal
Swing code
Movement pattern
Downward
Standard swing
(factory default)
Dual swing
Cyclic swing
button.
button to finish the setting.
Swing
Horizontal
Downward
Horizontal
Downward
EN
24-EN