Page 1: Table Of Contents
User Manual of 600 series Radio Remote Control By Alex, Version:201012, China Faryuan, www.ele-b2b.com Contents Introduction Safety Instruction Definition of model and function introduction 600 Series definition Introduction for the transmitter Introduction for the reciever Configuration and instruction The drawing and instruction of the transmiiter `s Configuraton...
Page 2 620S,620A System configuration How to set the jumper How to set the transmitting frequency How to set ID codes Frequency and ID codes cross-references Installation Instruction Installation notice Fasten the receiver System test Using Notice Troubleshooting tips System parameter...
Page 3: Introduction
Faryuan keep on develop and make technology first, try to be a leader of wireless remote control field. The design of 600 series wireless remote control system, is based on the maximal safeguard for the user ,and can pass kinds of interfere test of complex condition .
Page 4: Safety Instruction
100 hours in the smallest distance. Safety Instruction 600 series wireless remote control system are relatively simple to use, however, please read manual before installation,and operate with correct procedure. It can bring good effect with correct installtion and use 600 series wireless remote control system.
Page 5 The points should be followed when using ● ◆ Check the transmitter casing and pushbuttons daily.Should any damage be found,the unit should be removed from service. ◆ The transmitter voltage should be checked.If the voltage is low(red status light blinking or completely off),the batteries should be replaced. If the transmitter is not used for a long time, please take out the batteries and keep it safe。...
Page 6: Definition Of Model And Function Introduction
Definition of model and function introduction ★ Definition for 600 series Affixal function The sort of model Serial number of design ★ Introduction for functions of transmitter 600S： 6X one speed buttons ● ① ③ ② ① Shell ② Power switch ④...
Page 7 600A： 6X one-speed buttons+1 ● switchover buttons+1 interlock button ① Shell ① ② Power switch ③ ② ③ EMS button ④ Down ④ ⑤ ⑤ Up ⑥ West ⑥ ⑦ ⑦ East ⑨ ⑧ South ⑧ ⑨ North AB AUX , Auxiliary Micro-button A1: AUX Switchover button A2: Interlock button...
Page 8 610A： 2 two-speed buttons + 4 one-speed buttons ● +1AUX switchover button+1interlock button Attached drawing and instruction ◆ ① ① Shell ③ ② Power switch ② ③ EMS button ④ Down ④ ⑤ ⑤ Up ⑥ West ⑥ ⑦ ⑦ East ⑨...
Page 9 620A：6 directions, two speed buttons+1 ● AUX switchover buttons+1 interlock button Attached drawing and instruction ◆ ① ① Shell ② Power switch ③ ② ③ EMS button ④ Down ④ ⑤ ⑤ Up ⑥ West ⑥ ⑦ ⑦ East ⑨ ⑧...
Page 10: Introduction For The Reciever
★ Introduction for the reciever ① ⑤ ⑦ ④ ⑧ ⑥ ② ③ Front Back ① LED Indicator light ② Nameplate ③ Cable ④ The terminal of the controlbox ⑤ Fastness screws1 ⑥ Fastness screws2 ⑦ Anti-vibration spring ⑧ Installation screw...
Page 11: Configuration And Instruction
RADIO Configuration and instruction ★ Draw of Transmitter `s Configuration Transmitter 1、Wireless data module 2、IP code dip-switch 3、Battery contact 4、Micro-cpu 5、Power switch 6、EMS button 7、Double speed button 8、Indicator light ★ Receiver configuration 1、Wireless data module 2、Micro-cpu 3、Position for the function 4、Indicator light 5、Wire terminal 6、Relay...
Page 12: Wiring Diagram
Wiring diagram ★ 600S,600A ★ 610S,610A ★ 620S,620A Power Power Power Power Power Power Down Down Down Down Down East West East East West West Main Main Main South South South North North North Ground Ground Ground Note: please install the yellow-green wire into the equipment shell rightly.
Page 13: System Configuration
System configuration ★ How to set the jumper The receiver has three function position (details see the picture),you can set your system function to meet your different requirement, the detailed function settings as follows: ◆ Special function settings Join the terminal to the receiver port P3,the relay action for button B is lock form;...
Page 14 ◆ Finishing the setting of dial-up swich, please cut off the power, and then it will be effective after electricity. ◆ 600 series supply more than 256 channels for your choice, please choose the allowed channel to operate, we promise most channels is available and reliable, but not sure every channel, if you find wrong channel, please trip off to use.
Page 15 The following drawing is ID code programming device ● This ID code is 8-position binary system code. Every binary system code match to a unique FR channel and transmitting frequency. ( Please to the Frequency and ID Code Matching Table). As the drawing shows, “1” is the bottom slot of ID code.
Page 16 ★ Frequency and ID Code Matching Table Frequency Frequency Frequency Frequency Frequency ID Code ID Code ID Code ID Code ID Code （MHZ）（MHZ）（MHZ）（MHZ）（MHZ） 408.4 00000000 418.8 00110100 429.2 01101000 439.6 10011100 11010000 408.6 00000001 00110101 429.4 01101001 439.8 10011101 450.2 11010001 408.8 00000010 419.2 00110110 429.6 01101010 10011110 450.4 11010010 00000011 419.4 00110111 429.8 01101011 440.2 10011111 450.6 11010011...
Page 17 Frequency Frequency Frequency Frequency Frequency ID Code ID Code ID Code ID Code ID Code （MHZ）（MHZ）（MHZ）（MHZ）（MHZ） 414.6 00011111 01010011 435.4 10000111 445.8 10111011 456.2 11101111 414.8 00100000 425.2 01010100 435.6 10001000 10011100 456.4 11110000 00100001 425.4 01010101 435.8 10001001 446.2 10111101 456.6 11110001 415.2 00100010 425.6 01010110 10001010 446.4 10111110 456.8 11110010 415.4 00100011 425.8 01010111 436.2 10001011 446.6 10111111...
Page 18: Installation Instruction
Installation instruction ★ Installation notice Check and confirm the control traveling crane is normal ● before installation. Turn off the power. ● For the receiver position, wherever the crane goes, ● it should not impact any building extruded. The receiver should be fixed tightly, ●...
Page 19: Fasten The Receiver
If must be inside the box, then please install the Antenna outside the box. Receiver Receiver Babl e Ele. box Ele. box ★ Fasten the receiver Please install the receiver properly to avoid the shake ●...
Page 20: System Test
Installation of the shockproof spring ★ System test Notice: ● please sure that all wiring is right and under good protection, all screws are tight, fix the cable between the reciever and the crane to avoid the cable be short by the crane shake. Then open the crane power supply.
Page 21 Test process ● ◆ First loosen the EMS button,method: rotate the button 1/4 circle clockwise, it will bounce automatic. Then rotate the left rotory switch to “ON” position, the center indicator will be red, later turn to blue. Note 1: when you press the EMS button, you must redo the above operation to open the receiver.(loosen the EMS, and rotate the switch to ON position) Note 2: don’t press any button of the transmitter during the power on, or it will make the transmitter into protection.(not sending any signal)
Page 22: Using Notice
Using Notice Install the alkalic battery rightly, suggest to use above 1600AH ● battery to make the use time reach 100hours. Don’t use NIH battery, its voltage is only 1.2V. Make sure the Red EMS button is loose and then turn the emitter ●...
Page 23 Every time you press EMS button,the emitter will send stop signal ● to the receiver continously, the signal keeps 3 seconds then stop sending, you must press EMS button to continue. If you turn the power to “OFF”, then the EMS is invalid. Before close the power of the emitter, please press the red EMS ●...
Page 24: Troubleshooting Tips
Troubleshooting tips ◆ If the remote control is not working, please remove the failure according the following explain. ◆ When the controller can’t work normally (pressing the emitter buttons, the receiver has not action), please check the failure by the following steps: Item Failure description Method...
Page 25 Item Failure description Method ◆ Confirm if the relay output fuse melt, if it is necessary, please use the spare fuse Some actions is not ◆ Comfirm if original cable control system working works, if so, find the factory to repair. ◆...
Page 26: System Parameter
system parameter 600 new double speed series ● Constant technique parameter ● Receiver 600S 600S 600A 620S 620A Work voltage DC12V,DC24V,AC85-400V Connection mode Pin insert terminal block Relay capacity 10A 250V Respond time <100ms Use temperature -20-70℃ Antenna outside Defend grade IP66 The emitter Model...

This manual is also suitable for:

620s 620a