Totally Enclosed Box Type - Toshiba TOSVERT VF-S11 Specifications

Totally enclosed box type

Operation panel
●
● Frequency setting potentiometer
● Operation switch
● Slots for additional switches (Two)
● Power switch for motor circuit breaker
Line-up
Applicable motor (kW)
Input voltage
class 0.2 0.4 0.75 1.5 2.2 4.0 5.5 7.5 11
IP54
1-phase 240V
IP54
3-phase 240V
3-phase 500V IP54 IP00
External dimensions
(Mounting dimension)
External dimensions
Input voltage Aplicable motor
Inverter type
class
(kW) W
0.4 VFS11-2004PME
210
0.75 VFS11-2007PME
1.5 VFS11-2015PME
3ph-240V
215
2.2 VFS11-2022PME
4.0 VFS11-2037PME 230
0.75 VFS11-4007PLE
215
1.5 VFS11-4015PLE
2.2 VFS11-4022PLE
230
4.0 VFS11-4037PLE
3ph-500V
5.5 VFS11-4055PLU
400
VFS11-4075PLU
7.5
11 VFS11-4110PLU
450
15 VFS11-4150PLU
0.2
VFS11S-2002PLE
0.4 210
VFS11S-2004PLE
1ph-240V 0.75 VFS11S-2007PLE
1.5 VFS11S-2015PLE 215
2.2 VFS11S-2022PLE 230
Possible to bring
into compliance with
IP55 specifications!
Totally enclosed structure compliant with IP54
●
● Built-in noise filter
15
Equipped with all control devices as standard
●
(Control devices compliant with IP55
specifications / All-in-one)
● Built-in motor circuit breaker
Minimum wiring
●
Cooling structure: Self-cooling type
●
(Mounting dimension)
Dimensions (mm)
Cabling hole Drawing
H D W1 H1 D2
240 163.3 192 218 13.7 F
297 192.3 197 277 13.7
F
340 208.3 212 320 13.7
297 192.3 197 277 13.7
F
340 208.3 212 320 13.7
600 243 310 570 - - G
700 267 340 670 - - G
240 163.3 192 218 13.7 F
297 192.3 197 277 13.7
F
340 208.3 212 320 13.7
Standard specifications
Item
Input voltage class
Applicable motor (kW)
Input voltage class
1ph-240V class
3ph-240V class
3ph-500V class
Capacity(kVA)
Note 1)
Rated output current
(A) Note 2)
Output voltage
Note 3)
Overload current rating
Power Voltage-frequency
supply
Allowable fluctuation
Protective method
Cooling method
Color
Built-in filter
Service environments
Ambient temperature
Storage temperature
Relative humidity
Vibration
Note 1: Capacity is calculated at 220V for the 240V class and at 440V for the 500V class.
Note 2: Indicates rated output current setting when the PWM carrier frequency (Parameter F300) is 4kHz or less. When exceeding 4kHz , the rated output current setting is indicated in the parenthesis.
Note 3: The maximum output voltage is equal to the input supply voltage.
Note 4: ±10% when the inverter is operated continuously (under a load of 100%).
Note 5: The factory default settings of the following parameters are different from those of the standard type.
The factory default settings of all other parameters are the same as those of the standard type.
For parameter settings, see the tables of parameters on page 10. periodically.
Note 6: Installation environment
Install the inverter in a well-ventilated place and mount it on a flat metal plate in portrait orientation. Install the inverter so that it is not inclined more than ±10° from the vertical.
Leave a space of 10 cm or more on the upper and lower sides of the inverter, and a space of 5 cm or more on each side.
The inverter has a cooling fan to circulate air in it. The cooling fan has a useful life of approximately 30,000 hours (2 to 3 years when operated continuously), so it needs to be replaced
periodically.
Compliance with IP55
IP54-compliant structures refer to structures that protect the contents from dust and harmful effects of water that drops from every direction. The inverter can be
brought into compliance with IP55 specifications by making the wiring port watertight. (IP55-compliant structures refer to structures that protect the contents from
dust and harmful effects of water that comes in a jet from every direction.)
Note) 500V class 5.5 to 15kW range are IP00 type.
Standard connection diagram
Sink (Negative) logic : Common = CC
Main circuit power supply
240V class:
1ph/3ph-200 to 240V
-50/60Hz
500V class:
3ph-380 to 500V
-50/60Hz
Motor circuit breaker
R/L1
S/L2
Noise
T/L3 filter
Approx.weight
(kg)
FLC
3.9 FLB
Fault detection relay
FLA
5.9
RY
7.6
Low-speed
signal output
RC PLC
6.1
External 24Vdc
PLC
power input
8.0
FM
11.8
Meter
Frequency
meter
(ammeter)
17.0
❋1: The inverter comes with the PO and PA (positive) terminals short-circuited with a shorting bar. When connecting a DC reactor (DCL), detach the shorting bar.
4.0
❋2: When using the OUT output terminal in a sink logic configuration, do not short-circuit the NO and CC terminals.
❋3: When using the OUT output terminal in a sink logic configuration, do not short-circuit the P24 and OUT terminals.
6.0
7.6
* Other specifications are the same as those of the standard type. See common specification on page 6.
Specification
1ph-240V input class / 3ph-240V input class / 3ph-500V input class
0.2 0.4 0.75 1.5 2.2
Type Form
VFS11S- 2002PLE 2004PLE 2007PLE 2015PLE 2022PLE
VFS11- – 2004PME 2007PME 2015PLME 2022PME
VFS11- – – 4007PLE 4015PLE 4022PLE
0.6 1.3 1.8 3.0/3.0/3.1 4.2
1ph-240V class 1.5 (1.5) 3.3 (3.3) 4.8 (4.4) 8.0 (7.9) 11.0 (10.0)
3ph-240V class – 3.3 (3.3) 4.8 (4.4) 8.0 (7.9) 11.0 (10.0)
3ph-500V class – – 2.3 (2.1) 4.1 (3.7) 5.5 (5.0)
240V class : 3ph-200V to 240V, 500V class : 3ph-380V to 500V
150% -60 seconds, 200% -0.5 second
240V class : 1ph/3ph-200V to 240V -50/60Hz,
500V class : 3ph-380V to 500V -50/60Hz
, frequency ±5%
Voltage +10%, -15%
Note4)
IP54 Totally enclosed type (JEM1030) /
Possible to bring into compliance with IP55
Self-cooling
Munsel 5Y-8/0.5
1ph and 500V class : High-attenuation EMI filter, 3ph-240V class : Basic filter
Indoor, altitude 1000m or less. Place not exposed to direct sunlight and free from of corrosive and explosive gases.
Note 6)
-10 to +40˚C
-25 to +70˚C
20 to 93%
5.9 m/s 2 or less (10 to 55Hz)
Title
Source (Positive) logic : Common = P24
DC reactor (DCL)
Main circuit power supply
❋
1 (option)
240V class:
1ph/3ph-200 to 240V
Braking resistor (option)
-50/60Hz
500V class:
3ph-380 to 500V
-50/60Hz
P0 PA/+ PB PC/-
Motor
U/T1 R/L1
V/T2 S/L2
I M
Main circuit
W/T3
T/L3
Operation switch
Control
Forward
circuit
F
FLC
Reverse
R
VF-S11 Reset FLB
RES
Fault detection relay
Preset-speed1
S1
Connector for
FLA
common serial
communications Preset-speed2
S2
SWI FM VIA
RY
Preset-speed3
SOURCE V V S3
Low-speed
Common
CC
signal output
RC
P24
Speed reach
signal output. External 24Vdc
SINK I I PLC
OUT Ry
power input
Frequency setting potentiometer
NO
❋ 2
CC
CC VIA VIB PP
Meter
Voltage signal: 0-10V
Frequency
(Current signal: 4-20mA)
meter
(ammeter)
3ph-500V input class
4.0 5.5 7.5 11 15
Form
– – – – –
2037PME – – – –
4037PLE 4055PLU 4075PLU 4110PLU 4150PLU
6.7/7.2 11 13 21 25
– – – – –
17.5 (16.4) – – – –
9.5 (8.6) 14.3 (13.0) 17.0 (17.0) 27.7 (25.0) 33 (30)
3ph -380V to 500V
150% -60 seconds, 200% -0.5 second
3ph-380V to 500V -50/60Hz
, frequency ±5%
Voltage +10%, -15%
Note4)
IP00 Open type (JEM1030) /
Cooling fin mountable out side
Forced air-cooling
Not painted
High-attenuation EMI filter
-10 to +40˚C
-25 to +70˚C
20 to 93%
5.9 m/s 2 or less (10 to 55Hz)
VF-S11 VF-S11
Function
Standard type otally enclosed type
Command mode selection 1 0
Frequency setting mode selection 0 2
DC reactor (DCL)
❋
1 (option)
Braking resistor (option)
P0 PA/+ PB PC/-
Motor circuit breaker
Motor
U/T1
V/T2
Noise
I M
Main circuit
filter
W/T3
Operation switch
Control
Forward
circuit
F
Reverse
R
VF-S11
Reset
RES
Connector for
Preset-speed1
S1
common serial
communications
Preset-speed2
SWI FM VIA S2
SOURCE V V
Preset-speed3
S3
PLC P24 Common
❋ 3
Speed reach
SINK I I
OUT
signal output
Frequency setting potentiometer
NO Ry
CC
FM
CC VIA VIB PP
Voltage signal: 0-10V
(Current signal: 4-20mA)