Toshiba TOSVERT VF-S11 Specifications page 7

Extended parameters 1
2005 Ver.112/113
Parameters for setting functions that cannot be fulfilled by basic parameters.
Input terminal functions assignment parameters
A variety of functions can be given to various compatible input terminals by assigning the function numbers
for the parameter in the table below.
Title Function Adjustment range
Always active function selection 1 0-75 (No function)
Always-active function selection 2 0-75 (ST)
Input terminal selection 1 (F) 0-75 (F)
Input terminal selection 2 (R) 0-75 (R)
Input terminal selection 3 (RES) 0-75 (RES)
Input terminal selection 4 (S1) 0-75 (SS1)
Input terminal selection 5 (S2) 0-75 (SS2)
Input terminal selection 6 (S3) 0-75 (SS3)
Input terminal selection 7 (VIB) 5-17 (SS4)
Input terminal selection 8 (VIA) 5-17 (AD2)
input terminal functions list
Function Function
Function Function
No. No.
0 No function 38 Frequency command forced switching
1 Standby 39 No.2 Switching of V/F setting
2 Forward run command 40 Combination of No. 5, 39 and 61
3 Reverse run command 41 Frequency UP signal input from external contacts
4 Jog run mode 42 Frequency DOWN signal input from external contacts
5 Acceleration/deceleration 2 pattern selection 43 Frequency UP/DOWN cancellation signal input from external contacts
6 Preset-speed command 1 44 Combination of No. 10 and 43
7 Preset-speed command 2 45 Inversion of No. 11
8 Preset-speed command 3 46 Thermal trip stop signal input from external device
9 Preset-speed command 4 47 Inversion of No. 46
10 Reset command 48 Forced switching from remote to local control
11 Trip stop command from external input device 49 Operation holding (stop of 3-wire operation)
12 Switching of command mode and frequency setting mode 50 Forced switching of command mode and terminal board command
13 DC braking command 51 Display cancellation of the cumulative power amount (kWh)
14 PID control prohibited 52 Forced operation (factory configuration required)
15 Permission of parameter editing 53 Fire-speed control
16 Combination of No. 1 and 10 54 Coast stop (gate off)
17 Combination of No. 1 and 12 55 Inversion of No. 10
18 Combination of No. 2 and 4 56 Combination of No. 1 and 2
19 Combination of No. 3 and 4 57 Combination of No. 1 and 3
20 Combination of No. 2 and 5 58 Acceleration/deceleration 3 selection
21 Combination of No. 3 and 5 59 Combination of No. 2 and 58
22 Combination of No. 2 and 6 60 Combination of No. 3 and 58
23 Combination of No. 3 and 6 61 Forced switching of stall prevention level 2
24 Combination of No. 2 and 7 62 Holding of RY-RC terminal output
25 Combination of No. 3 and 7 63 Holding of OUT-NO terminal output
26 Combination of No. 2 and 8 64 Cancellation (clearing) of operation command from panel
27 Combination of No. 3 and 8 65 PID control integral value clear
28 Combination of No. 2 and 9 66 Combination of No. 1, 2 and 6
29 Combination of No. 3 and 9 67 Combination of No. 1, 3 and 6
30 Combination of No. 2, 5 and 6 68 Combination of No. 1, 2 and 7
31 Combination of No. 3, 5 and 6 69 Combination of No. 1, 3 and 7
32 Combination of No. 2, 5 and 7 70 Combination of No. 1, 2 and 8
33 Combination of No. 3, 5 and 7 71 Combination of No. 1, 3 and 8
34 Combination of No. 2, 5 and 8 72 Combination of No. 1, 2 and 9
35 Combination of No. 3, 5 and 8 73 Combination of No. 1, 3 and 9
36 Combination of No. 2, 5 and 9 74 Combination of No. 1, 2 and 4
37 Combination of No. 3, 5 and 9 75 Combination of No. 1, 3 and 4
Output terminal functions assignment parameters
A variety of functions can be given to various compatible output terminals by assigning the function
numbers for the parameter in the table below.
Title Function Adjustment range
Output terminal selection 1A (RY-RC) 0-255 (LOW)
Output terminal selection 2A (OUT-NO) 0-255 (RCH)
Output terminal selection 3 (FL) 0-255 (FL)
Output terminal selection 1B (RY-RC)
0-255 (always ON)
Output terminal selection 2B (OUT-NO) 0-255 (always ON)
Output terminal logic selection (RY-RC, OUT-NO) 0, 1, 2, 3
Output terminal functions list
Function No. Function Function No. Function
0/1 Frequency lower limit 30/31 Ready for operation (including ST/RUN)
2/3 Frequency upper limit 32/33 Ready for operation (excluding ST/RUN)
4/5 Low-speed detection signal 34/35 Frequency VIB selection
6/7 completion of acceleration/deceleration signal 36/37 Fault signal (put out also at the time of a retry)
8/9 Designated frequency attainment signal 38/39 Specified data output
Failure signal (trip output) Specified data output 2
10/11 40/41
12/13 Over-torque detection 42/43 Cumulative operation time alarm
14/15 Start/Stop 44/45 Parts replacement alarm
16/17 OL pre-alarm 46/47 Braking sequence output
Braking resistor overload pre-alarm F terminal input signal
18/19 48/49
Over-torque detection pre-alarm Inversion of R terminal input signal
20/21 50/51
22/23 pre-alarm 52/53 Signal in accordance of frequency command
24/25 Small-current detection 54/55 Undervoltage detection
Significant failure Invalid settings, always OFF (ignored)
26/27 56-253
Insignificant failure Always OFF
28/29 254
Always ON
255
Note) For functions 0 to 55, even numbers are true logic and odd numbers are false logic.
Carrier frequency parameters
Set parameters related to deep carrier frequency motor noise.
Title Function Adjustment range
Default setting
PWM carrier frequency 2.0-16.0 (kHz)
0
Random mode 0: Invalid, 1: Automatic setting
1
Carrier frequency control mode selection 0, 1, 2, 3
2
3 Frequency command (terminal block) specialized parameters
10
Set characteristics if input frequency instruction is input from terminal block.
6
Title Function Adjustment range
7
8 Frequency priority selection 0 1
9 VIA input point 1 setting 0 100 (%)
0 500 (Hz)
5 VIA input point 1 frequency
VIA input point 2 setting 0 100 (%)
VIA input point 2 frequency 0 500 (Hz)
0 6 (same as )
Frequency setting mode selection 2
VIB input point 1 setting 0 100 (%)
VIB input point 1 frequency 0 500 (Hz)
VIB input point 2 setting 0 100 (%)
VIB input point 2 frequency 0 500 (Hz)
VIA input bias
VIA input gain
VIB input bias
VIB input gain
Input/output terminal function parameters
Set specific values for functions such as low-speed/signal output and speed arrival signal output.
Title Function Adjustment range
Low-speed signal output frequency 0 (Hz)
Speed reach setting frequency 0 (Hz)
Speed reach detection band 0 (Hz)
Analog/logic input function selection 0 4
(VIA/VIB terminal)
Frequency command agreement 0 (Hz)
detection range
Protection parameters
Set protection operations, trip output and alarm output settings etc.
Title Function Adjustment range
Auto-restart control selection 0, 1, 2, 3, 4
Regenerative power ride-through control (Deceleration stop) 0,1, 2
Retry selection (number of times)
0: Invalid, 1-10 (times)
Overvoltage limit operation (Slowdown stop mode selection) 0, 1, 2, 3
Supply voltage correction (limitation of output voltage) 0, 1, 2, 3
Stall prevention level 1 10-199 (%/A), 200 (Invalid)
Inverter trip retention selection
0, 1
Emergency stop selection 0, 1, 2
Emergency DC braking time 0 20 (s)
Output phase failure detection mode selection 0, 1, 2, 3, 4, 5
Motor 150%-overload time limit
10-2400 (s)
Input phase failure detection mode selection
0: Invalid, 1: Valid
Torque up parameters
Set to generate high torque to match load or motor.
Title Function Adjustment range
Default setting
Auto-tuning 0, 1, 2
4
Slip frequency gain 0-150
(%)
6
Automatic torque boost value 0-30
(%)
10
Motor rated current 0.1-100.0 (A)
255
Motor no-load current 10-90 (%)
255
Motor rated speed -1
100-32000 (min )
0
Speed control response coefficient 1-150
Speed control stability coefficient 1-100
Panel display parameters
Set if changing units displayed or various display methods.
Title Function Adjustment range
Unit selection 0: %, 1: A (ampere)/V (volt)
Free unit selection 0.00: Invalid, 0.01-200.0
Inclination characteristic 0: Negative inclination,
of free unit display 1: Positive inclination
Free unit display bias 0- (Hz)
Free step 1 (pressing a panel key once) 0.00: Invalid, 0.01- (Hz)
Free step 2 (panel display)
0: Invalid, 1-255
Standard monitor display selection 0,1,2,3,4,5,6,7
Canceling of operation command 0: Operation command canceled (cleared),
when standby terminal (ST) is turned off 1: Operation command retained
Panel stop pattern
0: Slowdown stop, 1: Coast stop
* 1: Default values vary depending on the capacity.
Extended parameters 2
Parameters for setting higher functions.
DC Braking parameters
Title Function
DC braking starting frequency
Default setting
DC braking current
12.0
DC braking time
0
Motor shaft fixing control
1
Multi-stage speed run parameters
Title Function
Preset-speed operation frequency 8
Default setting Preset-speed operation frequency 9
Preset-speed operation frequency 10
0
Preset-speed operation frequency 11
0
Preset-speed operation frequency 12
0.0
Preset-speed operation frequency 13
100
Preset-speed operation frequency 14
50 (WP)
Preset-speed operation frequency 15 (Fire-speed)
60 (WN)
1
Power generation braking parameters
0
0.0 Title Function
Dynamic braking selection
100
Dynamic braking resistance
50 (WP)
Dynamic braking resistor capacity
60 (WN)
No. 2 motor parameters
Title Function
Base frequency 2
Base frequency voltage 2
Torque boost value 2
Motor electronic-thermal protection level 2
Stall prevention level 2
Default setting
No. 2 and no. 3 acceleration/deceleration time setting parameters
0.0
0.0
Title Function
2.5
Acceleration time 2
0
Deceleration time 2
Acceleration/deceleration 1 pattern
2.5
Acceleration/deceleration 2 pattern
Acceleration/deceleration 1, 2, 3 selection
Acc/dec 1 and 2 switching frequency
S-pattern lower-limit adjustment amount
S-pattern upper-limit adjustment amount
Acceleration time 3
Default setting Deceleration time 3
Acceleration/deceleration 3 pattern
0
Acc/dec 2 and 3 switching frequency
0
0
Jog run parameters
2
3
Title Function
150
Jog run frequency
0 Jog run stopping pattern
0 Panel jog run operation mode
1.0
Jump frequency parameters
0
300
Title Function
1
Jump frequency 1
Jumping width 1
Jump frequency 2
Jumping width 2
Jump frequency 3
Default setting
Jumping width 3
0
50
Forward/reverse/start frequency parameters
* 1
Title Function
* 1
Priority selection (Both F-CC and R-CC are ON)
* 1
Starting frequency setting
1710
Operation starting frequency
40
Operation starting frequency hysteresis
20
Time limit for lower-limit frequency operation
Reverse-run prohibition
Analog/pulse train output setting parameters
Default setting
Title Function
0 Logic output/pulse train output selection (OUT-NO)
Pulse train output function selection (OUT-NO)
0.00
Maximum numbers of pulse train
1
Inclination characteristic of analog output
Meter bias
0.00
0.00
PID control setting parameters
0
0
Title Function
1
PID control waiting time
PID control
Proportional gain
0
Integral gain
Differential gain
2005 Ver.112/113
Communications functions parameters
Adjustment range Default setting Title Function
0.0- (Hz) 0.0 Communication rate
0-100 (%/A) 50 Parity
0.0-20.0 (s) 1.0 Inverter number
0: Invalid, 1: Valid (after DC braking) 0 Communication error trip time
Communication waiting time
Setting of master and slave for
communication between inverters
Adjustment range Default setting Communication command point 1 setting
Communication command point 1 frequency
- (Hz) 0.0
0.0 Communication command point 2 setting
- (Hz)
0.0 Communication command point 2 frequency
- (Hz)
0.0 Selection of communication protocol
- (Hz)
- (Hz) 0.0 Block write data 1
(Hz) 0.0 Block write data 2
- (Hz) 0.0 Block read data 1
- (Hz) 0.0 Block read data 2
Block read data 3
Block read data 4
Block read data 5
Adjustment range Default setting
Detailed protection settings parameters
0: Invalid, 1: Valid 0
1.0-1000 (Ω) * 1
Title Function
0.01-30.00 (kW) * 1
Stall prevention release mode
Small current detection current hysteresis
Small current trip/alarm selection
Small current detection current
Adjustment range Default setting
Small current detection time
25-500 (Hz) 50/60
Detection of output short-circuit during start-up
50-330 (V)/50-660 (V) 230/460/575
Over-torque trip/alarm selection
0-30 (%) * 1
Over-torque detection level
10-100 (%/A) 100
Over-torque detection time
10-199 (%/A), 200: Invalid 150
Over-torque detection level hysteresis
Cumulative operation time alarm setting
Over-voltage stall protection level
Undervoltage trip/alarm selection
Adjustment range Adjustment range Default setting
Trip at VIA low level input mode
0.0-3200 (s) 10.0
Annual average ambient temperature
0.0-3200 (s) 10.0
(parts replacement alarms)
0: Linear, 1: S-pattern 1, 2: S-pattern 2 0
0: Linear, 1: S-pattern 1, 2: S-pattern 2 0
1: Acc/dec 1, 2: Acc/dec 2, 3: Acc/dec 3 1
0.0- (Hz) 0.0
Title Function
0-50 (%) 10
Prohibition of parameter change
0-50 (%) 10
Prohibition of frequency setting on the operation panel (
0.0-3200 (s) 10.0
Panel operation prohibition (RUN/STOP keys)
0.0-3200 (s) 10.0
Prohibition of panel emergency stop operation
0: Linear, 1: S-pattern 1, 2: S-pattern 2 0
Prohibition of panel reset operation
0.0- (Hz) 0.0
Prohibition of / /
during operation
External connection input up/down setting parameters
Adjustment range Default setting
- 20.0 (Hz) 5.0
Title Function
0, 1, 2 0
Input from external contacts- UP response time
0: Invalid, 1: Valid 0
Input from external contacts- UP frequency step width
Input from external contacts- DOWN response time
Input from external contacts- DOWN frequency step width
Initial value of UP/DOWN frequency
Adjustment range Default setting
Saving of changed value of UP/DOWN frequency
0- 0- (Hz) (Hz) 0.0
0-30 (Hz) 0-30 (Hz) 0.0
Torque up detailed setting parameter
0- 0- (Hz) (Hz) 0.0
0-30 (Hz) 0-30 (Hz) 0.0
Title Function
0- 0- (Hz) (Hz) 0.0
Exciting current coefficient
0-30 (Hz) 0-30 (Hz) 0.0
Stall prevention control coefficient 1
Stall prevention control coefficient 2
Motor adjustment coefficient
Maximum voltage adjustment coefficient
Adjustment range Default setting
Waveform switching adjustment coefficient
0: Reverse, 1: Slowdown Stop 1
Starting current suppression function
0.5-10 (Hz) 0.5
0- (Hz) 0.0
Others/option settings parameters
0- (Hz) 0.0
0: Invalid, 0.1-600 (s) 0.1
Title Function
0, 1, 2 0
Droop gain
Droop insensitive torque band
Braking mode selection
Release frequency
Adjustment range Default setting
Release time
0: Logic output, 1: Pulse train output 0
Creeping frequency
0-17 (Same as ) 0
Creeping time
500-1600(PPS) 800
Free notes
1
0: Negative inclination, 1: Positive inclination
Parameter for option 1
0-100 (%) 0
Parameter for option 2
Parameter for option 3
Parameter for option 4
Parameter for option 5
Adjustment range Default setting
Step-out detection current level
0-2400 (s) 0
Step-out detection time
0: Invalid, 1: Valid 0
High-speed torque adjustment coefficient
0.01-100.0 0.30
* 1: Default values vary depending on the capacity.
0.01-100.0 0.20
0.00-2.55 0
Adjustment range Default setting
0, 1, 2, 3, 4 3
0, 1, 2 1
0-255 0
0: Invalid, 1-100 (s) 0
0-2 (s) 0.00
0, 1, 2, 3, 4 0
0-100 (%) 0
0.0-500.0 (Hz) 0.0
0-100 (%) 100
0.0-500.0 (Hz) 60.0
0, 1 0
0-5 0
0-5 0
0-10 0
0-10 0
0-10 0
0-10 0
0-10 0
Adjustment range Default setting
0, 1 0
1-20 10
0: Alarm only, 1: Tripping 0
0-100 (%) 0
0-255 (s) 0
0, 1, 2, 3 0
0: Alarm only, 1: Tripping 0
0-250 (%) 150
0-10 (s) 0.5
0-100 (%) 10
0-999.9 610
100-150 (%) *1
0, 1, 2 0
0: , 1-100 (%) 0
Invalid
1, 2, 3, 4, 5, 6 3
Panel settings parameters
Adjustment range Default setting
0: Permitted, 1: Prohibited 0
) 0: Permitted, 1: Prohibited 0
0: Permitted, 1: Prohibited 0
0: Permitted, 1: Prohibited 0
0: Permitted, 1: Prohibited 0
change 0: Permitted, 1: Prohibited 1
Adjustment range Default setting
0.0-10.0 (s) 0.1
0.0- (Hz) 0.1
0.0-10.0 (s) 0.1
0.0- (Hz) 0.1
(Hz) 0.0
0, 1 1
Adjustment range Default setting
100-130 (%) 100
10-250 100
50-150 100
0-200 * 1
90-120 (%) 104
0.1-14.0 (kHz) 0.2
0: Invalid, 1: Valid 0
Adjustment range Default setting
0-100 (%) 0
0-100 (%) 10
0, 1, 2, 3
0
-20.0 (Hz) 3.0
0.00-2.50 (s) 0.05
-20.0 (Hz) 3.0
0.00-2.50 (s) 0.10
0-65535 0
0-65535 0
0-65535 0
0-65535 0
0-65535 0
0-65535 0
10-150 (%/A) 100
0.0: Invalid, 0.1-25.0 (s) 0.0
0.00-650.0 0.00