Related Manuals for Strong SM-RAZOR-ART1-M
Summary of Contents for Strong SM-RAZOR-ART1-M
-
Page 1: Installation Manual
SM-RAZOR-ART1-M SM-RAZOR-ART1-M Strong™ Razor Series Articulating Mount for Medium Displays Strong™ Razor Single Arm Articulating Mount For Medium Flat-Panel TVs Installation Manual INSTRUCTION MANUAL... -
Page 2: Tools Required
SM-RAZOR-ART1-M Installation Manual 1. Warnings • Installation of this product should be done by a qualified professional. • Do not begin installation before reviewing and understanding these instructions. • E nsure the mounting wall used can safely support 4 times the combined weight of the mount and chosen display. • Under no circumstances should this product be mounted to metal studs. • The manufacturer does not accept responsibility for incorrect installation. This wall mount is intended for use only with the maximum weight CAUTION: of 50 lbs./22.67 kg. Use with heavier than the maximum weight indicated may result in instability causing possible injury. - Page 3 SM-RAZOR-ART1-M Installation Manual 4.2. Hardware Bag 1 (A) Phillips Head (B) Phillips Head (C) Phillips Head (D) Phillips Head Machine Screw, Machine Screw, Machine Screw, Machine Screw, M4x10 (4) M4x20 (4) M4x30 (4) M5x10 (4) (E) Phillips Head (F) Phillips Head (G) Small Nylon Spacer, (H) M5 Washer, Machine Screw, Machine Screw, OD12xID5.5x5 (8) M5x12x1 (16) M5x20 (4) M5x30 (4) Bag 2 (I) Phillips Head (J) Phillips Head (K) Phillips Head (L) Phillips Head Machine Screw, Machine Screw, Machine Screw, Machine Screw, M6x10 (4) M6x20 (4) M6x30 (4)
-
Page 4: Installation
SM-RAZOR-ART1-M Installation Manual 5. Installation Step 1. Install the Display Adapter Plate Figure 1. A. C arefully lay the display face-down on a soft surface. B. L ocate the four mounting holes in the back of the display housing. Try to thread screws (A through N) in until the correct thread is found for the holes. - Page 5 SM-RAZOR-ART1-M Installation Manual Step 3. Install the Mounting Bracket on the Wall A. For Mounting on a Stud Wall Important! If the optional Dual Stud Mounting Bracket (SM-RAZOR-ART1-BKT-20) is being used to hang the mount on the wall, refer to the SM-RAZOR-ART1-BKT-20 manual (included with the bracket) to complete Step 3.
- Page 6 SM-RAZOR-ART1-M Installation Manual B. For Mounting on a Concrete Wall Important! If the optional Dual Stud Mounting Bracket SM-RAZOR-ART1-BKT-20 is being used to hang the mount on the wall, refer to the SM-RAZOR-ART1-BKT-20 manual (included with the bracket) to complete Step 3.
- Page 7 SM-RAZOR-ART1-M Installation Manual Step 4. Attach the Arm Assembly to the Wall Plate A. Loosen the two upper clamping screws on the arm assembly. B. Align the arm assembly with the top and bottom rail of the wall plate. C. S lide the arm assembly into position while lowering and pushing it toward the wall. Loosen the upper clamping bolts more if the assembly will not clip onto the rail. D. Tighten the upper and lower clamping bolts using the small 4mm Allen wrench (T1). E. If the SM-RAZOR-ART1-BKT-20 is being used, the wall bracket end covers can now be installed. Figure 8. Figure 9.
- Page 8 SM-RAZOR-ART1-M Installation Manual 6. Adjusting Display Position 6.1. Horizontal Level Adjustments 1. L oosen the two locking nuts (W) at the bottom of the arm assembly end plate using the 8mm socket wrench (T3). (Figure 11) 2. Place a level on top of the display, and rotate the display until it is horizontally level. (Figure 12) 3. T ighten the locking nuts at the bottom of the arm assembly end plate and then loosen them ¼ turn. This will allow for the display to be positioned with minimal effort. 4. After adjustment is complete, tighten the nuts. Figure 11. Figure 12. +/- 4° Horizontal Level Adjustment Nuts (W) 6.2.
- Page 9 SM-RAZOR-ART1-M Installation Manual 6.3. Adjusting Home Position (Fully Retracted) The mount includes a home position latch that Figure 15. secures the arm to the wall mount. This prevents (Y) x1 the display from being pushed away from the wall due to cabling.
-
Page 10: Specifications
SM-RAZOR-ART1-M Installation Manual 7. Specifications Finish Type Powder Coated, Matte Finish Product Weight 13.30 lbs. Maximum Display Load 50 lbs. (22.67 kg) Minimum Mounting Pattern 100 x 100 VESA Maximum Mounting Pattern 200 x 200 VESA Retracted On-Wall Thickness (inches) 1.65” Maximum Extension (inches) 21.25” Pan/Swivel Range 180° Tilt Angle Range -11°, +5° Certifications 8. -
Page 11: Warranty
SM-RAZOR-ART1-M Installation Manual 9. Warranty Lifetime Limited Warranty Strong™ Mounts have a Lifetime Limited Warranty. This warranty includes parts and labor repairs Lifetime on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified or disassembled. Products to be repaired under this warranty must be returned to Snap AV or a designated service center with prior notification and an assigned return authorization number (RA). 10. Contacting Technical Support Phone: (866) 838-5052 Email: Techsupport@snapav.com Pg. 11 www.snapav.com Support: 866.838.5052... - Page 12 © 2013 STRONG™ 130820-1600...