Advertisement
Advertisement
Table of Contents
Related Manuals for Strong SM-ART1-S
Summary of Contents for Strong SM-ART1-S
- Page 1 SM-ART1-S Universal Single-Arm Articulating Mount Installation Manual...
-
Page 2: Specifications
Warnings • Read these instructions before attempting installation. • The wall or mounting surface must be capable of supporting three times the combined weight of the mount and the display. Reinforce the structure, if required. • Use appropriate safety gear and proper tools. •... -
Page 3: Hardware Kit
Hardware kit Bag 1 Wood screw ×2 Concrete anchor ×2 S3 Hex wrench S4 Hex wrench Bag 2 M4×10 Screw ×4 M4×20 Screw ×4 M4×30 Screw ×4 M5×10 Screw ×4 M5×20 Screw ×4 M6×10 Screw ×4 M6×20 Screw ×4 M5 Washer ×16 M8 Washer ×8 Nylon washer ×4 Required tools... -
Page 4: Installation
Installation Install the wall plate (drywall) Warning Secure this mount to a wooden stud that is capable of supporting three times the combined weight of the mount and the display. Locate the wall plate (2) and wood screws (A). Right Left 2. - Page 5 6. Drill a 3/16 in (5 mm) pilot hole at each marked location. Drill to a depth of at least 2 in (51 mm). 3/16" 3/16" 7. Move the wall plate back into position and attach it using the wood screws (A) from the hardware kit.
- Page 6 Install the wall plate (concrete) Warning Secure this mount to concrete that is capable of supporting three times the combined weight of the mount and the display. Locate the wall plate (2) and wood screws (A). 2. Use a stud finder to locate a single stud at the desired mounting location.
- Page 7 Warning If the concrete wall is covered by a layer of plaster or drywall, the concrete anchor must pass completely through the layer to rest flush with the concrete surface. 6. Move the wall plate back into position and attach it using the wood screws (A) from the hardware kit.
- Page 8 • If the back of the display is curved, has a protrusion, or if the mounting holes are recessed, it may be necessary to use the longer screws (F, G, I or K) and the spacers (N). Display Top View 2.
- Page 9 Final assembly To complete the installation, slide the mount with the display attached into the wall plate. The plastic tab at the top of the wall plate clicks to indicate that the mount is secure. 2. To remove the mount from the wall, push in on the plastic tab and carefully slide the mount upwards and out of the wall plate.
- Page 10 4. To use the integrated cable management feature: a. Remove the plastic covers located on the arms of the mount. b. Route the cables through the arms and re-attach the plastic covers. Leave enough slack in the cables so that they are not pulled or pinched when the mount is moved. c.
-
Page 11: Operation And Adjustment
Operation and adjustment To adjust the tilt angle or rotate the screen: a. Firmly grasp the sides of the display and carefully move it into position. a. If the mount is too difficult to move or is too loose to hold in position, adjust the three screws located directly behind the head of the mount using the S4 hex wrench (D). - Page 12 Araknis Networks, BakPak, Binary, Dragonfly, Episode, Luma, Mockupancy, Nearus, NEEO, Optiview, OvrC, Pakedge, Sense, Strong, Strong Evolve, Strong VersaBox, SunBriteDS, SunBriteTV, Triad, Truvision, Visualint, WattBox, Wirepath, and Wirepath ONE are also registered trademarks or trademarks of Snap One, LLC. Other names and brands may be claimed as the property of their respective owners.
Need help?
Do you have a question about the SM-ART1-S and is the answer not in the manual?
Questions and answers