Related Manuals for Strong SM-RAZOR-T-M
Summary of Contents for Strong SM-RAZOR-T-M
-
Page 1: Installation Manual
SM-RAZOR-T-M SM-RAZOR-T-L SM-RAZOR-T-XL Strong™ Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTALLATION MANUAL... -
Page 2: Specifications
CAUTION: This wall mount is intended for use only with the maximum weight of 80 lbs. (36.29 kg) for model SM-RAZOR-T-M, 100 lbs. (45.36 kg) for model SM-RAZOR-T-L, and 120 lbs. (54.53 kg) for model SM-RAZOR- T-XL. Use with heavier than the maximum weight indicated may result in instability causing possible injury. -
Page 3: Package Contents
M6 Metal Washer (x8) M8 Metal Washer (x8) L & XL Models Only (U) M5 x 12mm (S) OD13 x ID6 x 12mm (T) OD17 x ID8.5 x 12mm Philips Head Screw (x8) Black Nylon Spacer (x4) Black Nylon Spacer (x4) L & XL Models Only XL Model Only Wall Plate (x1) Extension Brackets (x2) Display Brackets (x2) XL Model Only pg.3 © 2013 Strong... -
Page 4: Installation
SM-RAZOR-T Installation Manual Installation Step 1. Pre-Drill Wall for Mounting Figure 1 XL Model only: If the vertical VESA Figure 1 XL Model Only XL Model Only pattern dimension on the display is greater than 400 mm (Figure 1, Dimension A), attach the extension brackets to the tops of the display brackets using the 8 included screws (U) so the brackets will reach... - Page 5 (Figure 3, Dimension A). B. Mark the wall where you want the top of the display to sit when hung. Subtract Dimension A from the desired mounting height on the wall to find the correct mounting height for the top of the wall plate. Figure 3 Top of TV pg.5 © 2013 Strong...
- Page 6 Step 3. Mount the Wall Bracket Assembly Mounting on a Stud Wall The wall plate is fastened to a stud wall using the included lag screws (A). Be sure to use the correct number of screws to fasten your mount as listed below: Model: Number of Lag Screws: SM-RAZOR-T-M: 4 (Figure 4) SM-RAZOR-T-L: 4 (Figure 4) SM-RAZOR-T-XL: 6 (Figure 5) A. Pre-drill holes into two wood studs using a 3/16” drill bit. Be sure to drill...
- Page 7 • C oncrete must be 2000 psi density minimum. Lighter density concrete may not hold anchors. • M ake sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. pg.7 © 2013 Strong...
- Page 8 SM-RAZOR-T Installation Manual Step 4. Hang Display onto the Wall Plate A. Carefully lift the display and place the bracket hooks over and onto the angled lip in the wall plate (Figure 8). Do not release the display until it is completely connected to the wall plate.
- Page 9 This could cause damage to the display or the mount when trying to disconnect the display brackets from the wall plate. pg.9 © 2013 Strong...
-
Page 10: Display Tilt Adjustment
SM-RAZOR-T Installation Manual Display Tilt Adjustment The SM-RAZOR-T mounts offer up to Figure 12 15° of downward tilt. The mount is flat Max 15° (0°) when pushed to the wall. Once the display is moved out, it tilts to 5° and then can be adjusted from 5-15°. -
Page 11: Lifetime Limited Warranty
SM-RAZOR-T Installation Manual Lifetime Limited Warranty Strong™ Mounts have a Lifetime Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. Lifetime This warranty shall not apply to products which have been abused, modified or disassembled. - Page 12 © 2013 STRONG™ 130410-1510...