Table of Contents
Advertisement
Quick Links
For Your Records and
Warranty Assistance
For reference, also attach your receipt or a copy
of your receipt to the manual.
__________________________________________
Sea Wind
Model Name
__________________________________________
23347
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
Form# 42843-01
20081023
©2008 Hunter Fan Co.
Model Type 7
Model Type 7
Model Type 7
Owner's Guide and Installation Manual
Advertisement
Table of Contents
Related Manuals for Hunter MODEL TYPE 7 23347
Summary of Contents for Hunter MODEL TYPE 7 23347
- Page 1 __________________________________________ Sea Wind Model Name __________________________________________ 23347 Model No. __________________________________________ Date Purchased __________________________________________ Where Purchased Form# 42843-01 20081023 ©2008 Hunter Fan Co. Model Type 7 Model Type 7 Model Type 7 Owner’s Guide and Installation Manual...
-
Page 2: Table Of Contents
8 • Operating and Cleaning Your Ceiling Fan ......11 9 • Troubleshooting ....12 ©... - Page 3 To install and use the accessories, follow the instructions included with each product. For quiet and optimum performance of your Hunter fan, use only Hunter speed controls. CAUTION: To reduce the risk of personal injury, attach the fan directly...
-
Page 4: Getting Ready
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •... -
Page 5: Installing The Hanger Bracket
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Flat Washer 42843-01 • 10/23/08 • Hunter Fan Company Hanger Bracket Canopy Screw Isolator 3”... -
Page 6: Assembling And Hanging The Fan
Ground Wire Step 3-3 #8-32 x 1” Screw 42843-01 • 10/23/08 • Hunter Fan Company 3-1. Position the square hanger so that the green ground wire attached to the square faces out of the large opening in the metal bracket. -
Page 7: Wiring The Fan
• The white (common) power wire from the ceiling to the white wire from the fan • The black power wire from the ceiling to the black wire from the fan • The black/white wire from the fan to the black/white wire from the ceiling. -
Page 8: Installing The Motor Housing
Rotate the fan housing to situate the screws in the narrow ends of the keyholes. 5-3. Install the two remaining canopy screws into the holes in the fan housing and into the hanger bracket. Securely tighten all screws. -
Page 9: Assembling The Blades
Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. 6-2. Attach each blade to a blade iron using three blade assembly screws. -
Page 10: Installing The Switch Housing
Align the side screw holes in the upper and lower switch housings. Attach the lower switch housing to the upper switch housing with three housing assembly screws. Note: You can customize your Hunter fan with a number of accessory light kits. 42843-01 • 10/23/08 • Hunter Fan Company Steps 7-1 –... -
Page 11: Fan
8 • Operating and Cleaning Your Ceiling Fan 8-1. Turn on electrical power to the fan. 8-2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low and Off. • Pull the chain slowly to change settings. -
Page 12: Troubleshooting
6. Check and tighten the screws in the switch housing mounting plate and in the upper and lower switch housing. Problem: Excessive wobbling. 1. If your fan wobbles when operating, use the enclosed balancing kit and instructions to balance the fan. 2. Tighten all blade and/or blade iron screws.