Owner’s Manual Contents Model Identification ......2 recautions to avoid Possible exPosure to excessive ....microwave energy ... 3 mPortant safety instructions Grounding Instructions ...... 5 Installation ......... 6 Display and Features ......7 Using the Oven Control ommercial icrowave (Electronic Models) ......
Model Identification When contacting ACP, provide product information. Product information is located on oven serial plate which is located on the back side of the oven. Record the following information: Warranty service must be performed by an authorized ACP servicer. ACP also recommends contacting an Model Number: _____________________________ authorized ACP servicer if service is required after Manufacturing Number: _______________________...
IMPORTANT SAFETY INSTRUCTIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING When using electrical equipment, basic safety precautions should be followed to reduce the risk of burns, electrical shock, fire, or injury to persons.
Page 4
DO NOT overcook food. Carefully attend oven liquid. Visible bubbling or boiling when the container when paper, plastic, or other combustible is removed from the microwave oven is not always materials are placed inside the oven to facilitate present. THIS COULD RESULT IN VERY HOT cooking.
The plug provided in product specifications (available on www. must be plugged into an outlet that is properly installed acpsolutions.com). When a microwave oven is on a and grounded. circuit with other equipment, an increase in cooking times may be required and fuses can be blown.
This could cause B—Allow at least 2” (5.1 cm) between air discharge on back microwave oven to operate improperly and could of oven and back wall. shorten life of electrical parts.
User Options in this manual. The switching operation of this microwave oven can cause voltage fluctuations on the supply line. The operation of this oven under unfavorable voltage supply conditions can have adverse effects. This device is intended for the connection to a power supply system with a maximum permissible system impedance Zmax of 0.10 Ohms at the interface point of the user’s supply.
Display and Features (some models) Cooking Display DISPLAYS DESCRIPTION READY displays when oven control will accept READY entries. 00:00 Displays cooking time. If stage cooking is programmed, total cooking time is displayed. Display HOLD These settings display the current power level used DEFR Some items in the display can be seen for the microwave.
Using the Oven Control (Electronic Control) Manual Time Entry To cook food using a specific entered time and power level. Interrupting Open oven door and place food in oven. Close door. Operation • READY displays. Fan and light will turn on. Open oven door or press STOP/ Press TIME ENTRY key.
Programming the Oven Control (Electronic Control) The display shows Programming Keys PROGRAM Oven is shipped from the factory for single key programming. To change the oven default to allow double key programming, see User Option When set to single key or section.
User Options (Electronic Control) Changing user options Didn’t like an option? Options such as single or double key programming, beep volume, and maximum cooking time can be changed to suit individual preferences. Factory settings are marked in bold. To change options: To change the oven back to the factory setting, simply select the 1.
Interrupting Operation Open oven door to interrupt operation or turn time entry knob counterclockwise to “0”. To resume microwave oven operation, close oven door. If time was changed to “0”, time will need to be reset. Changing Time and Canceling Mistakes Heating time can be changed at any time while the oven is operating.
Open oven door to interrupt operation or turn time entry knob counterclockwise to “0”. 70% 100% To resume microwave oven operation, close door, select power level pad, and turn knob. Changing Time and Canceling Mistakes Heating time and power level can be changed at any time while the oven is operating.
Interrupting Operation Open oven door to interrupt operation or turn time entry knob counterclockwise to “0”. To resume microwave oven operation, close oven door. If time was changed to “0”, time will need to be reset. Changing Time and Power/Canceling...
PART CARE AND CLEANING RECOMMENDATION Clean microwave oven with mild detergent in warm water using soft sponge or cloth. Wring sponge or cloth to remove excess water before wiping equipment. If desired, boil a cup of water in microwave oven to loosen soil before cleaning.
Before Calling for Service C on rm oven is p lug ged into dedic ated circu it. C on rm oven is o n g round ed a nd p olarized c ircuit. O ven does not opera te. (C ontact e lectric ian to con rm ) C hec k fuse or circuit break er.
Need help?
Do you have a question about the Microwave Oven and is the answer not in the manual?
Questions and answers