Related Manuals for Tempest LAMINAR ELECTRIC - LE
Summary of Contents for Tempest LAMINAR ELECTRIC - LE
- Page 1 Operations Manual POWER BLOWERS LAMINAR ELECTRIC - LE Special Operations Variable Speed (SP VS) AMERICAN MADE...
-
Page 2: Introduction
TEMPEST TECHNOLOGY CORPORATION® has earned a reputation as a leader and innovator in the air movement industry and continues in that role today. -
Page 3: About This Manual
CONTACT: If after careful review, any questions arise concerning any portion of this manual, please contact TEMPEST TECHNOLOGY CORPORATION® for assistance: ® TEMPEST TECHNOLOGY CORP. 4708 N. BLYTHE AVENUE FRESNO, CA 93722 Toll Free: 800.346.2143... -
Page 4: Table Of Contents
Table of Contents INTRODUCTION ABOUT THIS MANUAL CONTACT INFORMATION SAFETY GUIDE GENERAL INFORMATION BLOWER IDENTIFICATION SERIAL NUMBER LOCATION WARRANTY POWER BLOWER DATA POWER BLOWER INFORMATION OPERATING PROCEDURES 9-10 PRE OPERATION VISUAL INSPECTION OPERATION SET-UP STARTING, ADJUSTING, STOPPING MAINTENANCE PROCEDURES MAINTENANCE SCHEDULE TROUBLE SHOOTING NOTES 13-16... -
Page 5: Safety Guide
Safety Guide Failure to follow the operating, maintenance and lubrication requirements set forth in this Operation and Maintenance Manual may result in serious personal injury and/or damage to equipment. The following WARNING statements indicate potentially hazardous conditions for operators and equipment. Make certain that anyone who works on or around the blower has read and fully understands the safety precautions listed. -
Page 6: General Information
Blower Identification This plate/information may be located on the left or right side of the Blower. Warranty Warranty information on your unit can be found on the back page of this manual or by contacting TEMPEST TECHNOLOGY CORP.® Page 5... -
Page 7: Power Blower Data
Power Blower Data TYPE: Positive Pressure Ventilation Fan - Laminar Air Flow BLADE: AirFlex Fiberglass Reinforced Polyamide Blades BUSHING: Keyed Shaft and Set or Cap Screws SHROUD: “SP” Design Tapered Aluminum w/ Durable Powder-Coat Finish DRIVE: Direct-Drive Variable Speed Electric Motor (GFCI Compatible) FRAME: Rugged, Lightweight, Square-Steel Tubing with Powder-Coat Finish TILT MECHANISM:... - Page 8 Power Blower Data Continued SPECIAL OPERATIONS VARIABLE SPEED (SP VS) POWER BLOWERS Model Part # Blade Size Dimensions (WxDxH) Weight SP-18-V-2.0 700-452 18” 20.50” x 22.75” x 22.50” 110 lbs. 13,338 Page 7...
-
Page 9: Power Blower Information
Power Blower Information The TEMPEST POWER BLOWER® is a high powered, portable fan used for Positive Pressure Ventilation and Attack (PPV/PPA), ventilation techniques that quickly and efficiently replaces hazardous interior environments. Figure 1.2 PPV and PPA were pioneered in the fire fighting industry where fire fighters use the Figure 1.3 TEMPEST POWER BLOWER®... -
Page 10: Operating Procedures
VISUAL INSPECTION After receiving and unpacking your blower, be sure to carefully inspect it for any damage that might have occurred during shipping. Should you find any damage: PLEASE NOTIFY TEMPEST TECHNOLOGY CORP.® IMMEDIATELY AT 800.346.2143 Operation SET-UP, STARTING AND STOPPING Assuming the previous Pre-Operation instructions have been followed the blower is now ready to run. -
Page 11: Starting, Adjusting, Stopping
The SP VS is available in three settings, which may be changed at anytime. For information on how to adjust the set cord length and size, please contact TEMPEST TECHNOLOGY CORP.® SP VS Controller A) 15’ of 12 AWG B) 200’ of 10 AWG C) 200’... -
Page 12: Maintenance Procedures
Maintenance Procedures Although the Tempest Variable Speed Blowers are designed to eliminate most maintenance issues, it is imperative that the blowers be inspected before startup on each use. Please review the following list before using this product. MAINTENANCE SCHEDULE EVERY USE - INSPECT BLOWER FOR DAMAGE AND FIX IF ANY - TIGHTEN/REPLACE ANY LOOSE OR MISSING PARTS - INSPECT BLADE FOR NICKS/CUTS OR DAMAGE... -
Page 13: Trouble Shooting
Trouble Shooting - SP VS Many factors can contribute to or be the sole cause of problems for electric power blowers. This section will identify some of these problems and provide solutions to correct them. IF THE “ON” AND THE “STOP” LEDS DO NOT LIGHT UP: MAKE SURE BLOWER IS CONNECTED TO POWER SOURCE. -
Page 14: Notes
Notes: Page 13... - Page 15 Notes: Page 14...
- Page 16 Notes: Page 15...
-
Page 17: Notes
Notes: Page 16... -
Page 18: Exploded View
Electric Power Blowers Exploded View - SP VS Page 17... -
Page 19: Parts List
Electric Power Blowers Parts List - SP VS Page 18... -
Page 20: Warranty Information
“Committed to Firefighter Safety” Warranty Information Mission Statement Except as otherwise set forth below, any claim by Customer with reference to the Goods sold shall be deemed waived by the Customer unless submitted in writing to Tempest within the earlier of (i) five Making Hazardous (5) business days following the date Customer discovered, or by reasonable inspection should have Environments Safer...
Need help?
Do you have a question about the LAMINAR ELECTRIC - LE and is the answer not in the manual?
Questions and answers