Related Manuals for Genexis OCG-218
Summary of Contents for Genexis OCG-218
-
Page 1: User Manual
User Manual Routed Ethernet Gateway OCG-218 / OCG-220 / OCG-2018 / OCG-2020 PRELIMINARY - JAN. 2011 Copyright © Genexis BV. All rights reserved... -
Page 2: Table Of Contents
Routing...............................16 Access Control.............................17 Website Filter............................17 Firewall Settings...........................18 Inbound Filter............................20 Advanced Network..........................21 Tools ..........................22 Administrator Settings..........................22 Time..............................22 System...............................23 Dynamic DNS............................23 System Check............................23 Schedules............................24 Status ..........................25 Device Info............................25 Routing...............................25 Logs..............................25 Statistics.............................25 Internet Sessions..........................26 Firewall Holes............................26 Copyright © Genexis BV. All rights reserved... -
Page 3: Installation Guide
Installation guide Introduction Congratulation on your acquiring of the Genexis Routed Ethernet Gateway. The Routed Ethernet Gateway will enable you to utilize your internet connection at maximum speeds. This document describes how to install and how to configure the Genexis router. -
Page 4: The Side Of The Router
The side of the router is shown below. A short description of the port connections is given in the table below. The presence of the POTS voice ports, and the F-connector for CATV are depending on the configuration of your router, and may not be present. Copyright © Genexis BV. All rights reserved... -
Page 5: Installation
Step 3. Connect a computer to one of the routed LAN port on the Genexis router, using an Ethernet cable with a RJ-45 connector. Your provider can tell you which ports routing is enabled. - Page 6 This step is optional, and is only relevant if the router has a CATV receiver The indicator RTV indicates if the (radio and) television signal is enabled (LED ON). Your radio or television can be connected using a coaxial cable with a male F-connector. Copyright © Genexis BV. All rights reserved...
-
Page 7: Getting Started
"Local Area Connection" and click "Properties" ➢ Select "Internet Protocol (TCP/IP)". Click on "Properties" ➢ Make sure "Obtain an IP address automatically", and "Obtain DNS server address automatically" are selected. Save the settings by clicking "OK" Copyright © Genexis BV. All rights reserved... - Page 8 Make sure "Using DHCP" is selected. Save the settings by clicking "Apply" Step 2. Launch the web browser and check if your connection is working. If your connection is not working, please refer to the troubleshooting section. Copyright © Genexis BV. All rights reserved...
-
Page 9: Configuring The Router (Optional)
Log in as 'Admin' or 'User' which both default to a blank password. It is recommended to change the password after the first log in. Step 3. Configure the router to the desired configuration. Information about the settings can be found in the "Router settings" sections. Copyright © Genexis BV. All rights reserved... -
Page 10: Troubleshooting
Troubleshooting Copyright © Genexis BV. All rights reserved... -
Page 11: Appendix: Router Settings
RIP passwords, for example, to prevent routes from one subnet from being seen by a router on another subnet that has conflicting IP addresses. Enter the password twice for verification. Leave both password fields empty if RIP passwords are not used. Copyright © Genexis BV. All rights reserved... - Page 12 Broadcast only: Local network broadcast only. This setting is useful where there are no WINS servers available, however, it is preferred you try Mixed Mode operation first. This setting has no effect if the 'Learn NetBIOS information from WAN' is activated. Copyright © Genexis BV. All rights reserved...
- Page 13 An entry can be changed by clicking the Edit icon or can be deleted by clicking the Delete icon. When you click the Edit icon, the item is highlighted, and the "Edit DHCP Copyright © Genexis BV. All rights reserved...
-
Page 14: Advanced
Select a filter that controls access as needed for this virtual server. If you do not see the filter you need in the list of filters, go to the Advanced Inbound Filter screen and create → a new filter. Copyright © Genexis BV. All rights reserved... -
Page 15: Special Applications
An entry can be changed by clicking the Edit icon or can be deleted by clicking the Delete icon. When you click the Edit icon, the item is highlighted, and the "Edit Application Rule" section is activated for editing. Copyright © Genexis BV. All rights reserved... -
Page 16: Port Forwarding
Datagrams sent to this route are forwarded onto the given Gateway IP address for further processing. When unchecked, this route represents a local route for which this router has its own IP address with which to communicate. Copyright © Genexis BV. All rights reserved... -
Page 17: Access Control
Add Web Filtering Rule This section is where you add the Web sites to be used for Access Control. Website Enter the URL (address) of the Web Site that you want to allow; for example: URL/Domain Copyright © Genexis BV. All rights reserved... -
Page 18: Firewall Settings
Controls endpoint filtering for packets of the UDP protocol. Filtering TCP Endpoint Controls endpoint filtering for packets of the TCP protocol. Filtering Formerly, the terms "Full Cone", "Restricted Cone", "Port Restricted Cone" and "Symmetric" were used to refer Copyright © Genexis BV. All rights reserved... - Page 19 Note that this feature does not apply to the DMZ host (if one is enabled). The DMZ host always handles these kinds of sessions. Enable Enabling this option (the default setting) enables single VPN connections to a remote host. (But, for multiple VPN connections, the appropriate VPN ALG must be used.) Copyright © Genexis BV. All rights reserved...
-
Page 20: Inbound Filter
At the same time an "Admin" filter might only allows systems from your office network to access the WAN admin pages and an FTP server you Copyright © Genexis BV. All rights reserved... -
Page 21: Advanced Network
Enables the router to automatically generate its LAN-side IP address and communicate with other LAN computers that also implement auto-IP, even when the router's DHCP server function is disabled. Enable LAN Auto This option should normally remain enabled. Copyright © Genexis BV. All rights reserved... -
Page 22: Tools
NTP Server Used Select a Network Time Server for synchronization. You can type in the address of a time server or select one from the list. If you have trouble using one server, select another. Copyright © Genexis BV. All rights reserved... -
Page 23: System
You can use it to test whether a computer is running, and to get an idea of the quality of the connection to that computer, based on the speed of the responses. Copyright © Genexis BV. All rights reserved... -
Page 24: Schedules
This section shows the currently defined Schedule Rules. An entry can be changed by clicking the Edit icon or can be deleted by clicking the Delete icon. When you click the Edit icon, the item is highlighted, and the "Edit Schedule Rule" section is activated for editing. Copyright © Genexis BV. All rights reserved... -
Page 25: Status
The number of packets that were dropped while being received, due to errors, collisions, Dropped or router resource limitations. Collisions The number of packets that were dropped due to Ethernet collisions (two or more devices Copyright © Genexis BV. All rights reserved... -
Page 26: Internet Sessions
Windows Live Messenger Service -- but there are many other types. The router itself can even create holes for its own use. The firewall holes page shows currently open holes. It shows you the types of connections that can be started by Copyright © Genexis BV. All rights reserved... - Page 27 "Virtual server \ SMTP" shows that the hole was created as a virtual server rule for the Simple Mail Transfer Protocol.. Active For holes that are created by scheduled rules, shows whether the rule is currently scheduled. Copyright © Genexis BV. All rights reserved...
Need help?
Do you have a question about the OCG-218 and is the answer not in the manual?
Questions and answers