Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Huffy Manuals
  4. Fitness Equipment
  5. Pro Image Rim
  6. Owner's manual

Huffy Pro Image Rim Owner's Manual

Pro image rim
Hide thumbs

Advertisement

Quick Links

Download this manual
© COPYRIGHT 2000 by HUFFY SPORTS
P P r r o o I I m m a a g g e e R R i i m m
O O w w n n e e r r s s M M a a n n u u a a l l
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
WARNING!
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO PROPERTY.
Toll-Free Customer Service Number for U.S: 1-888-713-5488,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-333 061
Internet Address: http://www.huffysports.com
TOOLS AND MATERIALS
• Two People
• Step Ladder, 8 ft. (2.4 m)
• Wrenches (One) 3/4", (Two) 9/16" and
(Two) 1/2" or (Two) Adjustable Wrenches
1
REQUIRED
FOR ASSEMBLY:
11/03
P/N 211644

Advertisement

loading
Need help?

Need help?

Do you have a question about the Pro Image Rim and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Huffy Pro Image Rim

Summary of Contents for Huffy Pro Image Rim

  • Page 1 Toll-Free Customer Service Number for U.S: 1-888-713-5488, For Europe: 00 800 555 85234 (Sweden: 009 555 85234), © COPYRIGHT 2000 by HUFFY SPORTS P P r r o o I I m m a a g g e e R R i i m m...

  • Page 2: Safety Instructions

    • If technical assistance is required contact Huffy Sports. • Serious injury could occur if teeth/face come in contact with backboard, net or rim.
  • Page 3 ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to the instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
  • Page 4 Get to know the basic parts of your basketball system... PARTS LIST - See Hardware Identifier Item Qty. P/N 211644 11/03 BACK BRACKET BACK BRACKET Part No. Description 202604 Bolt, Carriage 3/8 x 4.75” Long 203474 Washer, Flat, 1”O.D. 203017 Hex Nut, 3/8”...
  • Page 5 HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #2 (2) Item #12 (2) Item #16 (4) Item #11 (2) HARDWARE IDENTIFIER (NUTS & WASHERS) Item #5 (2) Item #21 (2) Item #3 (2) Item #8 (2) Item #4 (2) Item #20 (2) Item #9 (2) Item #6 (8) Item #17 (4)
  • Page 6 Install two carriage bolts (2) through rim (1), washers (3), and lock washers (9) as shown. Tighten nuts (4) completely. NOTE: Perform this step twice as it is applied to both holes of rim bracket shown Place a special locking nut (20) approximately half-way up on each carriage bolt (2) as shown.

  • Page 7: Bottom View

    First, test fit spacer (10) into back bracket (13) and Carefully rock in a circular motion to ream out any excess paint from holes if necessary. Place rim (1) into back bracket (13) so that the holes are properly aligned. Then, insert spacer (10) through back bracket (13), nylon washers (22) and rim assembly (1).
  • Page 8 Install bolt (11) through top holes on bracket (13) using washers (6) and nut (5) as shown. Tighten completely. Attach rim assembly to backboard and support structure by inserting bolts (16) through bottom holes in back bracket (13). Secure with nuts (17) and washers (6). Tighten nuts (17) completely.
  • Page 9 Position rim assembly (1) 90 degrees to back bracket (13) as shown. Place inner-bracket (14) over both carriage bolts (2) followed by springs (7), washers (8) and special nuts (21). Lower lower rim down. Holes in inner bracket (14) should line up with holes in backboard bracket (13).
  • Page 10 Secure back bracket (13) fully to backboard by inserting bolts (16) through upper holes in back bracket (13), Add washers (6) and nuts (17) to bolts (16). Tighten nuts (17) completely. First, test fit spacer (10) into back bracket (13) and Carefully rock in a circular motion to ream out any excess paint from holes if necessary.
  • Page 11 Then, install bolt (11), washers (6), and nut (5) through spacer (10) and tighten completely. LEVELING AND TENSION ADJUSTING INSTRUCTIONS: Adhere leveling and tension adjusting label (23) to inside of rim cover plate (15). TO LEVEL RIM, TIGHTEN OR LOOSEN THESE NUTS TO ADJUST RIM TENSION , TIGHTEN OR LOOSEN THESE NUTS 202531...

  • Page 12: Outside View

    Apply logo label (19) to cover plate (15). Install cover plate (15) on rim (1) using self tapping screws (12) as shown (note orientation of cover plate). NOTE: Cover plate (15) will fit over back bracket. Secure net (18) to rim (1). P/N 211644 11/03 OUTSIDE VIEW...