Table of Contents
Advertisement
Quick Links
REQUIRED TOOLS
AND MATERIALS:
• 2 People
• Tape Measure
• Wood Board
(scrap)
• Sawhorse or
Support Table
• Tape
• Safety Glasses
• #3 Phillips
Screwdriver
• Needle-Nose Pliers
• (2 each) Wrenches
7/16"
1/2"
9/16"
3/4"
AND/OR
• Socket Wrenches and Sockets
(Deep-Well Sockets are
Recommended).
7/16"
1/2"
9/16"
3/4"
• Garden Hose or Sand
• Step Ladder 8ft. (2.4 m)
OPTIONAL TOOLS
AND MATERIALS:
• Large & Small Adjustable
Wrenches
Portable System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
WARNING!
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO
PROPERTY.
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-632 7921
Internet Address: http://www.huffysports.com
1
Write Model Number
From Box Here:
01/06
ID# M732201
Advertisement
Table of Contents
Related Manuals for Huffy M732201
Summary of Contents for Huffy M732201
- Page 1 OR DAMAGE TO PROPERTY. Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339, For Europe: 00 800 555 85234 (Sweden: 009 555 85234), For Australia: 1-800-632 7921 Internet Address: http://www.huffysports.com Write Model Number From Box Here: 01/06 ID# M732201...
-
Page 2: Before You Start
Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. Not all items pictured are included with every model. ID# M732201 01/06 WARNING Read and understand warnings listed below before using this product. -
Page 3: Safety Instructions
• If technical assistance is required, contact Customer Service. • Adult supervision is recommended when adjusting height. Most injuries are caused by misuse and/or not following WILL VOID WARRANTY. rules for safe operation of the system. instructions. Use caution when using this system. 01/06 ID# M732201... - Page 4 IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL TOLL-FREE NUMBER: U.S. 1-800-558-5234; CANADA: 1-800-284-8339; http://www.huffysports.com Be sure to check inside pole sections; hardware and additional parts are packed inside. ID# M732201 01/06 NOTICE TO ASSEMBLERS periodically inspect for loose small parts. IMPORTANT! Remove all contents from boxes.
-
Page 5: Front View
Get to know the basic parts of your basketball system... FRONT VIEW BACK VIEW BACKBOARD BACKBOARD POLE POLE ELEVATOR ADJUSTMENT SUPPORT STRUT SUPPORT STRUT BASE BASE 01/06 ID# M732201... - Page 6 Plug Cap NOTE: Hardware kit is designed for more than one style of basketball system. Not all hardware will be used. ID# M732201 01/06 PARTS LIST - See Hardware Identifier Item Qty. * You many have extra parts with this model.
- Page 7 HARDWARE IDENTIFIER (NUTS & WASHERS) Item #13 (1) Item #9 (1) Item #16 (6*) Item #38 (7) Item #18 (2) Item #39 (1) Item #12 (6) Item #23 (1) Item #37 (1) You may have extra parts with this model. 01/06 ID# M732201...
- Page 8 Item #7 (1) Item #44 (1*) HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS) Item #33 (4) Item #41 (4) Item #45 (1) Item #17 (4) HARDWARE IDENTIFIER (OTHER) Item #40 (1) Item #31 (1) Item #30 (1) Item #32 (1) ID# M732201 01/06...
-
Page 9: Section A: Assemble The Base
Correctly identify each pole section and mark indicated distance from ends with tape as shown. ITEMS REQUIRED FOR THIS SECTION (2) 1/2” and (2) 9/16" Wrenches AND/OR (2) Socket Wrenches and Sockets 1/2” 9/16” Tape TOP POLE 31” MIDDLE POLE 43” BOTTOM POLE 43” 01/06 ID# M732201... - Page 10 IMPORTANT! Align dimple of top pole section (4) into trough of middle pole section (5) as shown. pole middle 5" ID# M732201 01/06 STICKER pole middle 1-1/2" DIMPLE HOLE CAUTION! THE IDENTIFICATION STICKER IS LOCATED 5"...
- Page 11 THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 1-1/2" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. RODS SHOWN ARE FOR VISUAL REPRESENTATION OF ALIGNMENT AND ARE NOT SUPPLIED WITH THE HARDWARE 01/06 ID# M732201...
- Page 12 A deep socket is recommended. IMPORTANT! THE SPACER (17) WILL FIT LOOSELY UNTIL SECURED INTO THE CAVITY OF THE BASE. ID# M732201 01/06 IMPORTANT! The Warning Label should be facing towards the front. WARNING! TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE.
- Page 13 Rotate the non-secured ends of base struts (10) as shown. Secure both base struts (10) to base using bolts (15), washers (12), and nuts (16). NOTE: ORIENTATION OF STRUTS TIGHTEN BOLT (11) IN LOCK NUT (13) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. WARNING! 01/06 ID# M732201...
-
Page 14: Section B: Attach The Backboard
IMPORTANT! DO NOT TIGHTEN COMPLETELY NOTE ORIENTATION. Identify elevator tubes (43). Toward Board ID# M732201 01/06 ITEMS REQUIRED FOR THIS SECTION (2) 1/2”, (2) 9/16” and (2) 3/4” Wrenches (2) Socket Wrenches and Sockets Elevator tube AND/OR 3/4” 1/2” 9/16”... - Page 15 Attach lower elevator tubes (43) to backboard brackets (29) using spacers (17, 23, 41, and 45), bolts (42) ratchet (28), and nuts (38) as shown. TOP VIEW OF RATCHET ASSEMBLY IMPORTANT! TIGHTEN ALL COMPONENTS COMPLETELY (STEP 1-4) 01/06 ID# M732201...
- Page 16 Insert T-bolt (36) through Slam Jam bracket (32) as shown. Secure Slam Jam bracket (32) and backboard bracket (29) assemblies to backboard. Using bolt (15) and nut (16) as shown. ID# M732201 01/06 Stretch spring (40) into position with pliers from clevis pin (34) to board bracket (29).
- Page 17 Attach upper elevator tubes (43) to backboard brackets (29) using spacers (41) bolt (42) and nut (38) as shown. Support pole on sawhorse. Attach upper and lower elevator tubes (43) to upper pole section (4) using bolts (42) and nuts (38) as shown. Attach pole cap (22) as shown. 01/06 ID# M732201...
- Page 18 Attach outer handle tube (47) to upper elevator tubes (43) using bolt (42) spacers (33) and nut (38) as shown. Attach outer handle tube (47) to lower elevator tubes (43) using bolt (42) spacers (33) and nut (38) as shown. ID# M732201 01/06...
- Page 19 Slide inner handle tube (48) into outer handle tube (47) as shown. Secure inner handle tube (48) to outer handle tube (47) using screws (20) as shown. Slide handle (46) onto inner handle tube (48). 01/06 ID# M732201...
- Page 20 B. Install reinforcement bracket (31) onto T-bolt (36) as shown. C. Install spring (30) onto T-bolt (36) as shown. D. Install special nut (39) and washer (37) onto T-bolt (36). E. Tighten special nut (39) until flush with end of T-bolt (36). NOTE: ORIENTATION OF BRACKET ID# M732201 01/06...
- Page 21 MOVING lowest position. SYSTEM 2. While holding pole, rotate basketball system forward until wheels engage with ground. 3. Move basketball system to desired location. 4. Carefully rotate basketball system upright. 5. Check system for stability. 522730 06/05 01/06 ID# M732201...