Advertisement
Quick Links
A Huffy Company
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY
RESULT IN SERIOUS INJURY,
PROPERTY DAMAGE AND WILL VOID WARRANTY.
This unit is intended for display purposes only and
should not be used for play.
To ensure safety, do not attempt to assemble this system without
following the instructions carefully. Check entire box and inside all
packing material for parts. Before beginning assembly, read the
instructions and identify parts in this document. Proper and
complete assembly, use and supervision is essential for proper
operation and to reduce the risk of accident or injury. A high
probability of serious injury exists if this system is not installed,
maintained, and operated properly.
• During assembly, if using a ladder use extreme caution. Two
people are recommended for this operation.
• If technical assistance is required, contact Huffy Sports' Sample
and Display Technician.
• Serious injury could occur if teeth/face come in contact with
backboard, net or rim.
• Display recommended for 3" (7.6 cm) or 3-1/2" (9 cm) Round or 4"
(10 cm) Square poles only.
• All instructions and warnings MUST accompany any display item
that is sold.
Most injuries are caused by misuse and/or not following
Use caution when installing this unit.
IMPORTANT!
To ensure prompt and correct handling of any problems, or to answer any questions, please contact the Sample
and Display Technician at 1-800-558-5234.
Model 89780
instructions.
Internet Address: http://www.huffysports.com
REQUIRED TOOLS AND
• Wrenches: (Two each) 7/16", 1/2", 9/16",
and 3/4" or Pliers
• 3/16" Allen Wrench
• Step Ladder, 8 ft. (2.4 m)
1
Customer Service
N53 W24700 South Corporate Circle
Sussex, WI 53089
U.S.A.
MATERIALS:
P/N 211487C
04/02
Advertisement
Related Manuals for Huffy 89780
Summary of Contents for Huffy 89780
- Page 1 • During assembly, if using a ladder use extreme caution. Two people are recommended for this operation. • If technical assistance is required, contact Huffy Sports’ Sample and Display Technician. • Serious injury could occur if teeth/face come in contact with backboard, net or rim.
-
Page 2: Parts List
P/N 211487C 04/02 PARTS LIST Item Qty. Part No. Description 203257 Zip Tie 207103 Pole Cap for 3.5” Pole Section 203100 Nut, Hex Flange 5/16-18* 204872 Height, Decal 201611 Bolt, Hex Flange, 5/16-18 x 3” 203218 Washer, Flat, 5/16* 200516 Bolt Cover, Vinyl* 200863 POP Header Cards... - Page 3 Move display to location on sales floor and remove 2 X 4 runners under feet. Install pegboard panels onto corresponding side support railings. Secure with zip tie to temporarily hold panel in place. Remove zip ties after assembly is complete. Attach P.O.P. sign (11) with plastic push clips (9) so that it faces aisle as shown.
- Page 4 Install support railings, as shown. Insert particle board as shown and rest on second support railing. IMPORTANT: Top Support Railing Must Be Inserted In The Positions Shown. POP Cards Will Later Be Inserted Into Rail NOTE: Use shorter bolts to assemble.
-
Page 5: Top View
Install enclosed pole mounting hardware and pole for each assembly. 908811 3-1/2” Rnd. Pole X 30” Pole 3-1/2” Rnd. Pole 3-1/2” Rnd. Pole NOTE: Enclosed One Set Of Hardware For (Each) Pole Installation VIEW FRONT WARNING TWO PEOPLE ARE NECESSARY TO MOUNT THE ELEVATOR ASSEMBLY TO THE POLE. -
Page 6: Installation Diagram
Assemble display products per diagram below and procedures on following pages for each model. Then mount to corresponding backboard hardware. 48” Fan Backboard w/Slam Jam Rim HUFFY TUFF LINE-UP 73092 44” Fan Backboard w/Slam Jam Rim P/N 211487C 04/02 81410... - Page 7 A B C Pole Locations Refer To Combo For Goal Assembly Instructions Mount extension arm and rim to backboard and finger tighten. NOTE: For spring loaded rim assembly, refer to instructions included with rim hardware. Secure hardware to extension arm as shown and tighten completely.
- Page 8 Insert header cards (8) into place as shown. P/N 211487C 04/02...