Related Manuals for Zektor Z57BD2C
Summary of Contents for Zektor Z57BD2C
- Page 1 Designed by you. Built by us. ™ Zektor 2CAT™ Z57BD2C HDMI™ 1.3 over CAT5 Extender with Bi-directional IR Pass-through User Manual Assembled in the USA...
-
Page 2: Safety And Notice
Safety and Notice The Zektor 2CAT™ Z57BD2C HDMI™ 1.3c over CAT5e/6 extender with Bi-directional IR Pass-through has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the Z57BD2C should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. - Page 3 HDMI™ sources from the remote site instantly. The Z57BD2C includes two units: Z57BD2C [TX] as the transmitting unit and Z57BD2C [RX ] as the receiving unit. The transmitting unit is used to transfer the audio/video and capture and receive IR signals through two low cost Cat-5/5e/6 cables.
-
Page 4: Specifications & Package Contents
1 Watt [max] Operation temperature 0~40°C [32~104°F] Storage temperature -20~60°C [-4~140°F] Relative humidity 20~90% RH [no condensation] 1x Z57BD2C [TX & RX ] 2x IR blaster Package Contents 2x IR receiver 1x 5V power adapter 1x User Manual ~ 3 ~... -
Page 5: Panel Descriptions
3. HDMI IN: Connect to a HDM™I source with a HDM™I male-male cable here Rear Panel — Transmitting Unit Z57BD2C [TX] 4. A/V SIGNAL: Plug in a Cat-5/5e/6 cable that needs to be linked to the A/V SIGNAL port of the receiving unit Z57BD2C [RX ]. - Page 6 Front Panel — Receiving Unit Z57BD2C [RX ] 6. IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver. 7. IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster 8. HDMI OUT: Connect to a HDMI™ display with a HDMI™ male-male cable here.
-
Page 7: Pin Definition
Pin Definition HDMI™ Pin 1 TMDS Data2+ Pin 8 TMDS Data0 Shield Pin 15 Pin 2 TMDS Data2 Shield Pin 9 TMDS Data0– Pin 16 Pin 3 TMDS Data2– Pin 10 TMDS Clock+ Pin 17 DDC/CEC Ground Pin 4 TMDS Data1+ Pin 11 TMDS Clock Shield Pin 18... -
Page 8: Ir Pass-Through
IR Pass-through IR Blaster IR Receiver IR Sockets IR Blaster: Plug in the IR blaster here to emit all IR command signals received from the IR receiver to control the HDMI source devices. IR Receiver: Plug in the IR receiver here to receive all IR command signals from the IR remote controls of the HDMI source devices. -
Page 9: Hardware Installation
IR sensor of the HDM™I source device(s). 3. Connect your HDMI or DVI display (such as a LCD or plasma HDTV) to the receiving unit Z57BD2C [RX ]. 4. Connect the IR receiver and blaster to the receiving unit Z57BD2C [RX ], and typically make the IR receiver directly point to the user. - Page 10 Notice 1. If the DVI or HDMI™ device requires the EDID information, please use EDID Reader/Writer to retrieve and provide EDID information of the DVI or HDMI™ display. 2. All HDM™I over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz UTP cable and ASTRODESIGN Video Signal Generator VG-859C.
-
Page 11: Limited Warranty
Proof of sale may be required in order to claim warranty. Customers outside Taiwan are responsible for shipping charges to and from Zektor Incorporated . Cables and power adapters are limited to a 30 day warranty and must be free from any markings, scratches, and neatly coiled.